Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 22 ksi, and the normal stress in steel rod (3) must be limited to 13 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 7 kips, Q 4 kips, R = 17 kips and S = 20 kips. =

Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 22 ksi, and the normal stress in steel rod (3) must be limited to 13 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 7 kips, Q 4 kips, R = 17 kips and S = 20 kips. =

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hollow tube ABCDE constructed of monel-metal is subjected to five torques acting in the directions shown. The tube has an outside diameter d2= 1.0in. The allowable shear stress is 14,950psi and the allowable rate of twist is 2.45degree/ft. Determine the maximum permissible inside diameter d1 of the tube in inches. Use G= 9500ksi.
The bell-crank mechanism is in equilibrium for an applied load of F1 = 19 kN applied at A. Assume a = 280mm, b = 170mm, c = 80mm, and θ = 45°. Pin B is in a double-shear connection and has a diameter of 30 mm. The bell crank has a thickness of 29 mm. Determine the bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest tenths.
Three round bars welded together are axially loaded as shown. Find the normal stress in each bar if P=15 kN
Design a rigid flange coupling to transmit a torque of 257N-m between two coaxial shafts. The shaft is made of alloy steel, flanges out of cast iron and bolts out of steel. Four bolts are used to couple the flanges. The shafts are keyed to the flange hub. The permissible stresses are given below: Shear stress on shaft =100MPa Bearing or crushing stress on shaft =250MPa Shear stress on keys =100MPa Bearing stress on keys = 250MPa Shearing stress on cast iron = 200Mpa Shear stress on bolts =100MPa
Two identical steel [E = 200 GPa] pipes, each with a cross-sectional area of 2800 mm2, are attached to unyielding supports at the top and bottom, as shown. At flange B, a concentrated downward load of P = 240 kN is applied. Determine the normal stress in the upper pipe (1).
A circular shaft A-B-C is hollow and is acted upon by a load P1=7565 N at the topmost part. A secondary load is P2 and is uniformly distributed around the cap plate at B. The diameters and thicknesses of the upper and lower parts of the shafts are dAB=31.75mm, tAB=12.7 mm, dBC=57.15 mm, and tBC=9.525 mm, respectively (a) Evaluate the normal stress LaTeX: \sigma_{AB} in the upper part of the shaft (b) The designer desired that the lower portion of the circular shaft to have the same compressive stress as the upper portion, what should be the magnitude of the load P2 (c) If P1 should remain at 7565N and P2 is now set at 10057 N, What new thickness of BC will result in the same compressive stress in both parts?
The rigid block has a weight of 80 kips and is to be supported by posts A and B. These are made of A-36 steel, and the post-C. which is made of C 83400 red brass. If all the posts have the same original length before they are loaded, determine the average normal stress developed in each post when post C is heated so that its temperature is increased by 20∘F. Each post has a cross-sectional area of 8 in2.
The plate shown is fastened to the fixed member by seven 12-mm diameter rivets. Compute the polar moment of inertia, J. Determine the value of the loads P so that the maximum shearing stress in any rivet does not exceed 75 MPa. If P = 8000 N, what is the minimum shearing stress developed in the rivet.
Load P is applied to joint D and the temperature increases by 50 °F. There are two steel (E = 29*10^6 psi; a = 6.5*10^-6/°F) AD and DC and a bronze (E = 16*10^6 psi; a = 9*10^-6/°F) BD with a length of 50 inches. Each bar is a 0.75 inch diameter. Find the deformation of every rod, the displacement at D, and the stress in each rod.
The assembly consists of two posts AD and CF made of A-36 Steel (E= 200GPa) and having a cross-sectional area of 1000m^2 and a 2014-T6 aluminum (E=73.1GPa) post BE having a cross-sectional area of 1,500m^2. If a central load of 400KN is applied to the rigid cap, determine the normal stress in each post. There is a small gap of 0.10mm between the post BE and the rigid member ABC.
The bell-crank mechanism is in equilibrium for an applied load of F1 = 11 kN applied at A. Assume a = 250mm, b = 100mm, c = 90mm, and θ = 40°. Pin B is in a double-shear connection and has a diameter of 29 mm. The bell crank has a thickness of 31 mm. Determine the shear stress in pin B and bearing stress in the bell crank at B. Express your answer in MPa rounded to the nearest hundredths.
Determine the adequacy of a 600 mm diameter (internal) steel pipe of length 2500 m with a thickness of 20 mm if it is capable of carrying a maximum stress of 125 MPa. The pipe is connected to a reservoir whose water surface elevation is at elevation 200 m. and discharge freely into air. A valve at the lower end of the pipe (elev. 0 m) is to be closed quickly. Cwfor Hazen-William’s Equation is 120 for the pipe and take bulk modulus of the water equal to 2.07X106 KPa while modulus of elasticity for steel is 200,000 MPa.