Calculate the maximum, unfactored tensile dead load the angle bar can sustain based on gross yielding by LRFD if Fy = 248 MPa and that service tensile live load is 135 KN. Use resistance factor = 0.9. Write your final answer to the nearest whole number in kN. Angle bar, 150x90x8 mm, 20-mm-dia. bolts 40 | 40|40| O O O O 57 63 _D 50.

Calculate the maximum, unfactored tensile dead load the angle bar can sustain based on gross yielding by LRFD if Fy = 248 MPa and that service tensile live load is 135 KN. Use resistance factor = 0.9. Write your final answer to the nearest whole number in kN. Angle bar, 150x90x8 mm, 20-mm-dia. bolts 40 | 40|40| O O O O 57 63 _D 50.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.6.3P

See similar textbooks

Similar questions

I need a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala For the beam loaded as shown, find the maximum tensile and compressive bending stresses and maximum shearing stress.. IN.A=4*10mm* 80mm 100mm 60mm 60mm 1.5KN 2kN/m 1mal A |-----|- | Im ++ Im->> 3m 3kN/m
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. Use a501 plate and a502 gr2 rivet a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
H.W A Solid Steel bar of dlameter 6omm and length 350 mm is Placed inside an aluminum cylinder öf Inside diameter Femm and out side d lameter Ilomm, a comPressive load of looo lais applied on the assembly, find the stresses in the bar and the cylinder ? take Est = 200GPa and EAl = F0GPan %3D Cover Plate 0.25mm d- do 35omm A lum. cylinder Steel bar
sted ingid 250MM B k steel bar bolt AUR rigid bar 12 mm thick 8 mm Brass 350mm Jointd 16 mene thick 350mm JointB 250 mm Xg = 20x10% Eg = 90 G Pa -6 A, = 12x10/0 Es = 200 G Pa thickness> 16 mm 8 mm bolt %3D 12 mmi thick shear strength f bolf bearing streng th of holt= 100 la 50 MPa %3D Assume no failure will take place in steel or brass. Temperature chauge brass steel on Temperature change on Determine thai can be applied to system - the max
Prob 01: An 18” depth beam is bolted to a 24” depth girder is connected similar to that in figure shown below. Thediameter of the rivet is 20mm and the angles are each 100mm x 100mm x 12mm thick. For each bolt, assume thatthe allowable bearing stress is 220 MPa. Determine the allowable load P in KN on the connection. *show all theload P in kN for bearing stressBeam web thickness = 5mmGirder web thickness =
Please write the complete solutions and Legibly. Rate will be given! Do not just copy asnwers in CHEGG! Thank you :) A singly reinforced rectangular beam 270 mm x 430 is reinforced with 4-16-mm-dia. rebars with yield strength 420 MPa. If bar centroid is located 70 mm from the bottom edge of the beam and f'c = 21 MPa, calculate the design moment strength in kN-m. Write your answer with 2 decimal places only.
ZAO O "l zain IQ YA docs.google.com/forms 10/.. find the shear stress in bolts 2 3 1. 5 4 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 110 MPa. 127 MPa. 509 MPa no one 0/10 find the tensile stress in upper plate in section 1-1 (2 (5 (3 1 4) + ...
8. H / The beam shown below has across seclion of channel Shape with width 360mm.and haghs h= loomm, the web thickness ist= 14mm.Deler- Mine ihe Max imum tensile aud Compressive stressin the beam due to unifom Load? 360Mm 3.6KN/M 14m tiom Please Sir 5T CASIC f-991ES PL DATURAL u CALC (-)
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
PROBLEM 7. Determine the largest load P that can be applied the plate and bolts. The bolt has a diameter of 12 mm and an allowable shear stress of 80 MPa. Each plate has an allowable tensile stress of 60 MPa, an allowable bearing stress of 70 MPa, and an allowable shear stress of 30 MPa. Answer: P = 25 kips (controls) P/2 P/2 30 mm- 15 mm P 30 mm
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in