Consider a square plate at rest in the horizontal plane with mass m, sides of length 2L, and center of mass at point G (located at the center of the square). Two forces are applied to the plate: FA is applied at corner A with some angle relative to the edge of the plate, and FB is applied at point B parallel with the edge of the plate, as shown. The resulting motion is a pure acceleration (translation) to the right of magnitude a. The plate does not rotate. Determine the magnitude of the force applied at B, ||FB||. (Hint: Use Euler's 2nd Law about an arbitrary point (in this case about point A).

Consider a square plate at rest in the horizontal plane with mass m, sides of length 2L, and center of mass at point G (located at the center of the square). Two forces are applied to the plate: FA is applied at corner A with some angle relative to the edge of the plate, and FB is applied at point B parallel with the edge of the plate, as shown. The resulting motion is a pure acceleration (translation) to the right of magnitude a. The plate does not rotate. Determine the magnitude of the force applied at B, ||FB||. (Hint: Use Euler's 2nd Law about an arbitrary point (in this case about point A).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A uniform rod of mass M = 2.3 kg and length L = 0.2 m, lying on a frictionless horizontal plane, is free to pivot about a vertical axis through one end, as shown. The moment of inertia of the rod about this axis is given by 1/3 ML2. If a force F = 7 N, q = 47° acts as shown, what is the resulting angular acceleration (in rad/s2) about the pivot point?
A weight with mass mw=150 g is tied to a piece of thread wrapped around a spool, which is suspended in such a way that it can rotate freely. When the weight is released, it accelerates toward the floor as the thread unwinds. Assume that the spool can be treated as a uniform solid cylinder of radius R=4.00 cm and mass Ms=200 g. Find the magnitude ?a of the acceleration of the weight as it descends. Assume the thread has negligible mass and does not slip or stretch as it unwinds. Use ?=9.81 m/s2. Find the tension T in the thread.
Two propellers of lengths and masses l, L and m, M rotate in the same direction, as shown in the figure. if the left propeller starts from rest, w1=0 and the right propeller starts with an angular velocity that the right propeller ends up with after both propellers have collided.
the cylinder with a mass m1=2kg and radius r=0,1m is placed at a plate with mass m2=4kg. We are applying force F at this plate. Find an acceleration of the plate, when the friction coefficient μ=0,2
Mason is is trying to keep a door open using a door stopper. That door is solid, and it has a mass of 18.3kg. The door closer is connected 26.2cm away from the hinge, and pulls with a force of 123N. The door stopper provides a static friction force of 13.2N, and a kinetic friction force off 11.8N. Find the angular acceleration (as a vector) of the door.
Blocks A and B shown in the figure have masses of 5 kg and 10 kg respectively.If the pulley is treated as a 3 kg solid disk with a 15 cm radius, determine the acceleration of the block A. Disregard the rope mass and any slip on the pulley.Consider that the moment of inertia of the pulley is given by Ip = (1/2)mr² in which m is the mass of the pulley and r is of radius the pulley.
A cylinder of mass M and radius R is rotated in a uniform V groovewith constant angular speed ω. The coefficient of friction betweenthe cylinder and each surface is μ. What torque must be applied tothe cylinder to keep it rotating?
Find: friction force between the spool and the ground. and the UNIT of measurement of the acceleration of the mass center of the spool
1) Three small spheres are rigidly mounted to a horizontal shaft with rotates with angularvelocity omega as shown. Neglect sphere radii, ignore gravity. Spheres have masses m1, m2andm3 as shown.a. What is the angular momentum HO about O the center of the coordinates shown?b. At this instant, what is Ax , the x component of the bearing force at A to offset the dynamicimbalance? Note that you are NOT asked to find any other forces (Ay, Ox, or Oy) in interestof time.
1. Using Lagrangian Mechanics, find the acceleration of the double Atwood machine assuming the pulley is massless
Four masses m1, m2, m3 and m4 are 10 kg, 20 kg, 30 kg and 40 kg respectively. The corresponding radii of rotation are 0.1 m, 0.15 m, 0.3 m and 0.35 m respectively and the angles between successive masses are 40°, 60° and 120°. Find the position and magnitude of the balance mass required, if its radius of rotation is 0.5 m.
a=22mist 16w/ Figure Q) “The mass of ahuckey puck 0.80Kg slides on horizontal, frictionless surface of an ice rink. If two hockey sticks srike the puck simulaneously, exerting the acceleration of the puck shown n figure 2. Determine both the magnitude and the direction of the puck’s forces?