Consider the column section below. It has eight #9 bars. The material properties are as follows: fr=4,000 psi, f, = 60 ksi, and E. = 29,000 ksi. The cross-sectional area of a #9 bar is 1.0 in.².8- #9O2.5" 44Axis ofbending20"20"15"► 2.5"PMThe column is subjected to a factored axial load P = 480 kips. Determine the maximum M₁that can be resisted by the section.

Consider the column section below. It has eight #9 bars. The material properties are as follows: f =4,000 psi, f, = 60 ksi, and E. = 29,000 ksi. The cross-sectional area of a #9 bar is 1.0 in.². 8- #9 оооо 2.5" 44 15" 20" Axis of bending 20" 2.5" P M The column is subjected to a factored axial load P₁ = 480 kips. Determine the maximum MẪ that can be resisted by the section.

Consider the column section below. It has eight #9 bars. The material properties are as follows: f =4,000 psi, f, = 60 ksi, and E. = 29,000 ksi. The cross-sectional area of a #9 bar is 1.0 in.². 8- #9 оооо 2.5" 44 15" 20" Axis of bending 20" 2.5" P M The column is subjected to a factored axial load P₁ = 480 kips. Determine the maximum MẪ that can be resisted by the section.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

To lower ends of the three bars in the figure two are the same level before the rigid homogeneous W=176kN block is attached. Each still bar has a length of 1.00 m, an area 500mm² and E=200 GPa. For the bronze bar the length is 1.6m, the area is 900mm² and E= 83 GPa. What is the stress developed in the bronze bar? What is the stress developed into steel bar? What is the elongation of each bar?
The rectangular piece of wood, 76 mm by 174 mm, is used as a compression block. The grain of the wood makes a 30.3º angle with the horizontal, as shown in the figure. Determine the shearing stress (in MPa) on the plane of the grain if the allowable compression stress on the plane of the grain is 20.2 MPa. Round off the final answer to four decimal places.
Solve the following problems completely and neatly. Use 3 decimal places in all your computations except for strain and rho(5 decimal places). Input your answer in the text box provided in each number. Calculate the depth of compression block of the section in PART B in mm.0
A 5.0m simple beam supports the given floor loads Wu and a concentrated load Pu due to the wall transverse to the given beam. Answer the following questions given the sections of the beam. Calculate the effective depth of the section in PART A in mm.0 Use 3 decimal places in all your computations except for strain and rho(5 decimal places).
Given Y = 9.79 kN/m^3 Find: P @ bottom of tank (kpa) Force (tensile) on each bolt (kN) Stress on each bolt (MPa)
Calculate the required amount of reinforcement (in in2) considering the ultimate moment below. Use english units. Note: Use the following equations for minimum reinforcement in English units. Pmin for flexure = (3*sqrt (f'c))/fy greater than or equal to 200/fy f'c = 3000 psi fy = 40 ksi Mult = 200 ft-k
the values are A = 3 , B = 4, C = 1, D = 0 please answer the forces
The following rigid structure ABCD is supported by a hinge at B and two bars at C and D. The applied load is 100 kN. The data is shown in the table. Determine: The stress in each bar. Answ: 27.01 MPa, 328.01 MPa The vertical displacement at the point where the load is applied. Answ: 0.9403 mm. The rotation at point B. Answ: 0.001069 rad. The horizontal displacement 400 mm below point B. Answ: 0.42741 mm.
pls help! Write the complete solutions and legibly. Answer in 2 decimal places. UPVOTE WILL BE GIVEN! MECHANICS OF DEFORMABLE BODIES Let Q = 0 and T = 6 (Example: 4QT mm2 = 406 mm2). Just substitute the number in letter. Thank you! A rigid beam is being supported by three suspender bars made of bronze and loaded as shown in the figure. The cross-sectional area of each bar is 4QT mm2. Determine the average axial stress in each bar.
The frame shown in the figure is supported by a hinge at E and roller at D. Compute the horizontal and vertical component of the hinge force at C. as it acts upon BD *use 3 decimal place in rounding off all throughout the solution.
What will be max. height that the water tank that will become full if the max. tangential stress is SNx10^2 psi? Show your solution in a short size coupon bond and convert it in pdf format. SN: 94
Need answer ASAP. Please be detailed and clear with your solution. II. Shown is a parabolic segment submerged vertically in water. W.S. 3 m 60 cm 3 m vertex 1) Determine the magnitude of the total force on one face of the area, in kN. * 2) Determine the location of the total force from the W.S. *