Design a two way slab using the Coefficient Method considering an interior panel (Case 2). The slab will carry retail storage from a commercial warehouse for service live load. The dimensions of the interior panel are 4.50 m x 5.50 m. Use 2015 NSCP Strength Design with f'c = 28 MPa and Fy = 276 MPa. Unit weight of concrete is 23.56 KN/cu m. Include simple structural details as part of your output at the end of your computations.

Design a two way slab using the Coefficient Method considering an interior panel (Case 2). The slab will carry retail storage from a commercial warehouse for service live load. The dimensions of the interior panel are 4.50 m x 5.50 m. Use 2015 NSCP Strength Design with f'c = 28 MPa and Fy = 276 MPa. Unit weight of concrete is 23.56 KN/cu m. Include simple structural details as part of your output at the end of your computations.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular concrete beam has a width of 300mm and an effective depth of 450 mm to centroid of the tension bars. The beam is reinforced with six-32 mm ᴓ tension bars placed in two layers with the outer layer having a depth of 478 mm, and two 28 mm ᴓ compression bars with centroid 65 mm from the extreme tension fiber. Use the 2010 NSCP, fc’ = 34.5 MPa and fy = 345 MPa. Assume the concrete displaced by the compression steel cannot be neglected and that compression steel yields. Determine the following: The balanced steel ratio if the beam is singly reinforced. The maximum steel ratio for a singly-reinforced section in tension control. The maximum steel area in mm2 for a doubly reinforced section in tension control.
Design the one-way slab to support a load of 12 kN/m² with a superimposed dead-to-live load ratio of 1:2. Assume concrete weighs 24 kN/m³. f'c = 28MPa and fy 420 MPa. Use p = Pmax. Let the length of the slab be 6 meters.
1- For the floor system shown in Figure below, support service live load 4KN / (m ^ 2) and service dead load 5KN / (m ^ 2) Answer the flowing. Classify the floor system into one way or two-way solid slab. 2- What is the minimun slab thickness that should be used to control deflection and shear requirement ? 3- By using Ø 12 mm rebar, what is the required positive and nagative reinforcement? 4- Sketch the detail of reinforcement. Use : fy = 400Mpa , f c ^ prime =30 Mpa 6.00 m 6.00 m6.00 m 3.00 m 0.30 m АB 3.00 m 3.00 m
A simply supported slab has a length of 3.5 m. It is topped with 25 mm thick grout (unit weight = 12 KN/cum) and 10 mm tiles (unit weight = 15 KN/cum). The main rebars is 10 mm spaced at 90 mm on centers. Use fy= 276 Mpa, fc’= 21 Mpa and unit weight of concrete is 23.5 KN/cum. Determine the uniform live load capacity of the slab.
Show complete solution and figures. Design a two way slab using the Coefficient Method considering an interior panel (Case 2). The slab will carry 2.40 KPa of service live load. The dimensions of the interior panel are 4.00 m x 5.00 m. Use 2015 NSCP Strength Design with f'c = 20.70 MPa and Fy = 276 MPa. Unit weight of concrete is 23.56 KN/cu m.
A 300 mm thick footing slab supports a 300 mm thick concrete wall carrying uniform service dead load of 145 kN/m and service live load of 215 kN/m. The base of the wall footing slab is 1.0 m from the ground surface. Design parameters are as follows: γsoil = 16 kN/m3, γconc = 24 kN/m3, qa = 200 kPa, f’c = 28 MPa and fy = 420 MPa. calculate the spacing of 12-mm-diameter rebars for flexure.
Design a 1 way slab to carry a live load of 4.8 KPa on a simple span of 4.50 m. Use f'c = 20.70 MPa, fy = 275 MPa and unit weight of concrete 23.56 KN/cu m. Use 2015 NSCP specifications Draw/sketch your final output with proper labeling of reinforcements/temperature bars
The 400mm x 400 mm square concrete column is reinforced by 6 - 25mm diameter steel bars. If the working stresses for steel and concrete are 345 MPa and 28 MPa, respectively, determine the largest axial force P that can be safely applied to the column. Use Est=200 GPa and Econcrete=25 GPa.
a 300 mm thick footing slab supports a 300 mm thick concrete wall carrying uniform service dead load of 214.31 kN/m and service live load of 145.94 kN/m. the base of the wall footing slab is 1.2 m from the ground surface. design parameters are as follows: ysoil = 16 kN/m^3, yconci = 24 kN/m^3. qa = 215.46 kPa. f'c = 27 MPa and fy = 420 MPa. 1. calculate the required center to center spacing of 16 mm bars for flexure if the maximum factored moment in the slab is 75 kN.m a. 150 mm b. 180 mm c. 210 mm d. NOTA 52. calculate the ultimate beam shear stress on the footing slab if the footing slab is 2.1 m wide. a. 1.25 MPa b. 0.74 MPa c. 0.87 MPa d. 0.96 MPa
A hollow, circular, steel column (E = 30,000 ksi) is subjected to a compressive load P. The column has length L = 8.0 ft and outside diameter d = 7.5 in. The load P = 85 k. If the allowable compressive stress is 7000 psi and the allowable shortening of the column is 0.02 in., what is the minimum required wall thickness t min?
A prestressed beam 300mmx600mm is subjected to a prestressing force after losses of 1000kN acting 150mm above the bottom of the beam by straight tendons. Normal concrete having unit weight of 23.5 kN/m^3 is used. If the modulus of rupture is 3MPa, compute the superimposed load that will produce cracking of the beam.
Principles of Reinforced and Prestressed Concrete PROBLEM A simply supported rectangular beam of length ? has a width of ? and an effective depth of ?. Compression steel bars are placed at a distance ?′ from the extreme concrete compressive fiber. The beam supports service dead loads of ?? and ??, respectively. Use ??′ = 28 ??? and ?? = 420 ???. For the reinforcements, use 4 25 ?? tension steel bars and 4 12 ?? compression steel bars. Given: b = 197.5 mm d=317.5mm d’=77.5mm L= 2.7 m Wd = 13.75 kN/m Wd = 17.75 kN/m