Design a wide-flange (W) column 20 ft. on length to support an axial load of 410 Kips in the interior of a building. The column base is rigidly fixed to the footing and the top of the column is rigidly framed to very stiff girders. Assume that bracing is provided to prevent sidesway in the weak deflection plane of the column, but the sidesway in the strong plane is not prevented. Select an economical W shape to satisfy the AISCS. Use A36 Steel. 14.31 In. |-- 10.13 in. I X- X 0.855 in. -0.510 in.

Design a wide-flange (W) column 20 ft. on length to support an axial load of 410 Kips in the interior of a building. The column base is rigidly fixed to the footing and the top of the column is rigidly framed to very stiff girders. Assume that bracing is provided to prevent sidesway in the weak deflection plane of the column, but the sidesway in the strong plane is not prevented. Select an economical W shape to satisfy the AISCS. Use A36 Steel. 14.31 In. |-- 10.13 in. I X- X 0.855 in. -0.510 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Design a wide flange W column 8 m in height to support an axial dead load of 1000 kN and a live load of 1200kN in the interior of a building. The column base is rigidly fixed to the footing and the top of the column isrigidly framed to very stiff girders. Assume that bracing is provided to prevent side sway in the weak axis/planeof the column (you don’t have to consider slenderness in this direction), but side sway is not prevented aroundits strong axis. Select an economical W shape.
Determine the reduced nominal moment capacity (φ Mn) of a 10-inch wide by 16-inch deep reinforced concrete beam. Take f'c as 5500 psi and the steel as Grade 60 bars. The tensionreinforcement consists of four #9 bars and the compression reinforcement is two #7 bars at the top of thebeam. Interior construction and #4 stirrups. Also solve for the reduction factor (φ).Please clearly state the depth to the neutral axis that you iterated for (i.e. ‘c’). Show the work for theiteration of ‘c’. As part of this iteration, you can stop iterating if your resultant tension and compressionforces are within 5% of each other.As part of solving for the reduced nominal moment capacity, solve for the reduction factor (φ)You DO NOT need to check the minimum reinforcement amounts per ACI (assume OK).DRAW the cross section and elevation view of this beam to scale.DRAW the strain distribution through the cross-section of the beam and label all dimensions.DRAW the stress distribution (simplified Whitney…
Draw the S.F. and B.M. diagrams for the overhanging beam carrying uniformly distributed load of 30kN/m over the entire length and a point load of (Your roll no.kN) as shown in figure. Locate the point of contraflexure.
A horizontal beam AB is freely supported at A and B, 8metres apart and carries uniformly distributed load of 15KN/m run (including its own weight). A clockwise moment of 160KN-M is applied at a point C, 3metres from left hand support A.using Macaulay method, calcite the beam at C if El=40×10^3KN-m^3
A 16-ft span beam is fixed at one end and simply supportedat the other end. A single concentrated load of 9600 lb is placed at the centerof the span. Find the vertical reactions and construct the complete shear andmoment diagrams.
A fixed beam of span 4m subjected to point load of 50 KN at 2m from lefthand support. Determine fixed end moment( FEM ).Also mention its nature.
A steel framework is used to support the 4" reinforced concrete slab that carries a uniform live loading of 1.9kPa. Sketch the loading that acts along members BE and FED. b = 3 m and a = 2.5 m.
The boom DF of the crane and the column DE have a uniform weight of 40 lb/ ft. A load of 300 lb is applied at hoist attached to F. Determine the resultant internal loadings in the crane on cross-sections through points A, B, and C.
Determine the maximum factored axial compression loadfor a W 10 × 49 column with an unbraced height of 15 ft. Assume K = 1.0.
Design a circular spiral column to support an axial dead load of 500 K and a live load of 230K. Use fc’=4ksi and fy=60 ksi and a steel ratio of about 4%. Also design the necessary spirals.
The steel framework is used to support the 5-in. reinforced stone concrete slab that carries a uniform liveloading of 450 lb/ft^2. Determine the loading that acts along members BE and FED. Set b = 12 ft, a = 8.5 ft. Known that Reinforced stone concrete has minimal density for desing loads 150 lb/ft^3
the concentrated load once at the beginning of the beam and once at the end and once at the middle distance between the two support Use influence line..