Statics of Rigid Bodies DETERMINE THE FORCE (Ib) FOR MEMBERACGIVEN THE DATA BELOW:F1586 lbF2 = 1,213 Ib**Note: for compression, include a negativesign ( - ) and for tension, type your answer asis. Input your answer in two (2) decimal placesonly without the unit.F1B30°60°60°АX1X2F2F2 DETERMINE THE FORCE (Ib) INMEMBER BD OF THE ROOF TRUSSSHOWN GIVEN THE DATA BELOW:F1 = 54 lbF2136 lb28 degreea =34 degree**Note: for compression, include a negativesign (- ) and for tension, type your answer asis. Input your answer in two (2) decimal placesonly without the unit.F1a|CАF2

F1=586 lbF2=1213 lbAngle between AB and AC is 30° As two questions have been posted, solution will…

Answered: DETERMINE THE FORCE (Ib) FOR MEMBER AC

Engineering

Civil Engineering

DETERMINE THE FORCE (Ib) FOR MEMBER AC

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Using the data given, determine the theoretical maximum density of the asphalt mix. SG bitumen, 1.02…

Q: CBR sample is prepared at the optimum moisture content and soaked in water for 3 days. True False

Q: trapezoidal dam wherein the upstream side is vertically straight and has a width at the top of 4 m,…

Q: The volume of one bag of cement is (a) 0.0214 cu.m (b) 0.0347 cu.m (c) 0.0434 cu.m (d) 0.0609 cu.m

A: 1 bag of cement contain 50 kg and has a volume around 1.226 cubic feet or 0.034722 cubic meter…

Q: 1. A camera was equipped with a 152mm (6”) focal-length lens is used to take a vertical photograph…

A: Given focal-length of lens, f = 152 mm Flying height, H = 2780 m Height of terrain above mean sea…

Q: The annual average precipitation is mm The annual average evaporation is mm Runoff coefficient @ sub…

Q: A steel bar AD has a cross-sectional area of 260 mm² and is loaded by forces P, = 12 kN, P, = 8 kN,…

Q: 100 kN 200 mm A, В 150 mm D 150 mm E F 75 mm-

Q: Determine the internal normal force, shear force, and bending moment acting at point C in the beam.

Q: 3. Determine the magnitude of the internal normal force, shear force, and the bending moment at…

Q: nown, and the Assume that us effects, the essure is

A: solution of above problem is below:

Q: Calculate the slope at C using ONE of these methods: double integration method, area-moment and…

Q: A viscous liquid (p = 1.2x10kg/m³, µ = 0.0048 Pa.s) flows at a rate of 10ml/s through a horizontal,…

Q: Illustrate the Influence Line and calculate the maximum positive live shear at point C in kN…

Q: Drum mix plant provide lower production rate of asphalt mix than the batch plant. True O False

A: Drum mix plant is a continuous flow plant in which the mix is happening contnously and have huge…

Q: Which of the following statements are True about the binder course layer? O The layer is cambered O…

A: Among the given statements, Second statement is true. Since the binder course is laid to transfer…

Q: Illustrate the Influence Line and calculate the maximum positive live shear at point C in kN…

Q: The venturi meter is being used to measure the flow of fuel oil (sp gr = 0.858). The %3D…

Q: During asphalt mix production the bitumen content is acceptable within the range of -0.2 and +0.2 of…

A: Following is required answer :

Q: Is also known as ice pellets. a. b. graupel b. c. freezing rain c. d. hail d. a. sleet

Q: A CAST IRON COLUMN OF CIRCULAR SECTION HAS A PROJECTING BRACKET CARRYING A LOAD OF 200 KN AT A…

A: The outside diameter of iron column, Do=300mmThe inside diameter of iron column, Di=250mmThe load…

Q: 1. The figure shows a looping water pipe system. The pressure drop stood at 200030> mmHg from point…

A: step 1-

Q: 18 21 32 F mm mm mm E A В D G F

Q: It is safe to assume that the one-year rainfall totals fit a normal, log-normal and log-Pearson…

A: Yes , one year rainfall fits to normal ,log normal , log Pearson distribution We can assume…

Q: Problem A sample of a dry coarse grained material of 500 grams was shaken through a nest of sieves…

A: Size of sieve for which 60% of sand passes, D60=2mmSize of sieve for which 300% of sand passes,…

Q: 1. For the beam shown in the figure below, draw the influence lines for Ra, Rc, Re, Vd and Md and…

Q: A trapezoidal load is acting in the middle portion AB of the double side overhanging beam as shown…

A: ∑MA=0-14 sin60°×1 + 20×4×2 + 12×20×4×13×4 - VB×4 + 10 = 0VB=52.80 kN ↑∑V=0VA+VB=14 sin60° + 20×4 +…

Q: ffee is draiming frod a conical filter Into a eyli o ffee pot at the rate of l0 m3/B46. How is the…

Q: Determine the corresponding compression force C in the cylinder BD.

Q: A CAST IRON COLUMN OF CIRCULAR SECTION HAS A PROJECTING BRACKET CARRYING A LOAD OF 200 KN AT A…

Q: a. What are cofferdams and what are they used for?

A: Cofferdams are water retaining structure.

Q: Two fixed frictionless inclined planes making an angle 30° and 60° with the horizontal are shown in…

Q: An average wastewater flow of 20 000 m³/ day is to be treated by a clarifier with surface overflow…

A: Sedimentation involves one or more basins, called “clarifiers.” Clarifiers are relatively large open…

Q: Using the following data, determine the total voids in the asphalt mix. * :2.355 Bulk specific…

Q: A rectangle has a base of 6 in. and a height of 12 in. Using the approximate method, determine the…

Q: For the beam shown, determine the support reactions. EI is constant.

Q: 500ft vertical curve has PVI elevation 240.31ft. the initial and final grades are 2.1% and -3.3%…

A: solution Given g1=2.1% ;g2=-3.3%so total change N =g1-g2=2.1-3.3=5.4%Length L =500ftelevation of…

Q: Explain the factors that affect local buckling

A: There are various factors that affect local buckling.

Q: A pressure gauge fitted on the side of a tank filled with liquid reads 50 kPa and 100 kPa at heights…

A: given- Pressure at height of 10 m=50 kPaPressure at height of 5 m=100 kPag=10 m/s2

Q: Determine the reaction at B using the moment-area theorem and draw the bending moment diagram. Mo B…

A: Need to determine the Reaction at B and Bending Moment Diagram

Q: Which of the following stability value for Marshall design is not comply with the standard? 750 kg…

A: Correct answer is 1000 kg Expansion :- The marshall stability value is defined as maximum load…

Q: 1. The 1.2.kg slider is released from rest in position A and slides without friction along the…

A: Given, Spring constant k=24 kN/mm=1.2 kg hA-hB=4.5 mg=10m/sec2

Q: The venturi meter is being used to measure the flow of fuel oil (sp gr = 0.858). The differential…

A: Find Headh=zSwSoil-1h=1610.854-1=2.73536inso,

Q: Rank the components circled below according to overstrength factors (Q.) to render the structure…

A: Over strength factor is defined as the ratio of maximum base shear in actual behavior to first…

Q: G Q1/ Water flow through an orifice meter at an empirical equation Re = 0.35RE0 and a rate of…

Q: A liquid limit test conducted on a soil sample in the cup device gave the following results: 10 19 |…

Q: Each of the four vertical links has an 8 X 36-mm uniform rectan- gular cross section, and each of…

Q: 214. The rigid bars AB and CD shown in the figure are supported by pins at A and C and the 2 rods.…

Q: The table below are the observation of a three-wire leveling from BM1 to BM2. If the elevation of BM…

Q: Water flows through a 4-in diameter pipe at a velocity of 10 ft/s. Find the volume flow rate in cfs.…

A: step 1-

Question

Statics of Rigid Bodies

DETERMINE THE FORCE (Ib) FOR MEMBER
AC
GIVEN THE DATA BELOW:
F1
586 lb
F2 = 1,213 Ib
**Note: for compression, include a negative
sign ( - ) and for tension, type your answer as
is. Input your answer in two (2) decimal places
only without the unit.
F1
B
30°
60°60°
А
X1
X2
F2
F2

DETERMINE THE FORCE (Ib) IN
MEMBER BD OF THE ROOF TRUSS
SHOWN GIVEN THE DATA BELOW:
F1 = 54 lb
F2
136 lb
28 degree
a =
34 degree
**Note: for compression, include a negative
sign (- ) and for tension, type your answer as
is. Input your answer in two (2) decimal places
only without the unit.
F1
a
|C
А
F2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Given

VIEW

Step 2 Determination of member force

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Two aluminum (Ea=77 GPa) rods AB and CD, and a steel (Es=202 GPa) rod EF support a 82.7 kN load P. Each of the rods has a 400 mm2 cross- sectional area. Neglecting the deformation of rod BED, determine the change in length (in mm correctly up to two decimal places) of rod AB. A C P 500 mm В E 400 mm F
Assume that the truss is simply supported at joints M and E. Determine the stress at member FC if Pu = 18.375 Kips, the area is 23 in?. Answer your problem with the given unit ksi. Pu Pu Pu Pu Pu Pu Pu * (a: 10' - J I H * (a 10' - RI K F Rv 8@10'=80
Q2: Find the permissible distance (X) for the beam shown in figure. If the stresses in tension is 40 MPa and in compresion is 80 MPa. 4kN 4KN. 220 16KN N. A 大 6m 'RB INA: 4 = 20* (o mm
Determine the maximum tensile and compressive bending stresses developed in the beam shown. The cross-section has the given properties. NA 1-35 x 10mm a. RA = b. RE= c. fb(c) = d. fb(T) = 80 mm 200 mm A 1.5m kN KN 5kN m MPa MPa B 1.5m SkN/m 2m 5KN n 2m 4
On the study roof truss shown in the figure, determine the force in element F G and ineach of the elements located to the right of F G. Also, indicate in your answer if the elements are intension or in compression.
Determine the forces in members BC and CG. The forces are positive if in tension, negative if in compression. A 18 kips Answers: BC= CG= i B 10' G i 14' 10' C 10' D F 50% E kips kips
Consider the truss shown in (Figure 1). Suppose that F = 30 kN Figure A 3m 3m < 1 of 1 ▼ Determine the force in the member CD of the truss and state whether it is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case tension. FCD- Value Submit Part B HA Part C Request Answer Determine the force in the member CB of the truss and state whether it is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. FCB- Value Submit Request Answer HÀ Submit Part D FDA- Value HA Determine the force in the member DA of the truss and state whether it is in tension or compression. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive…
Sispose that P = 30 kip, P=20 kip, and = 10 kip Figure ++. 400 San 184-399 30 Part A Determine the force in member GF of the bridge truss Express your answer in kilopounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension For Submit Part B Avec Fre Request Anst O? Determine the force in member PC of the bridge truss Express your answer in kilopounds to three significant figures. Enter negative value in the case of compression and positive value in the case of tension VAZO IT vec kip ? kip
ASSUME THAT THE TRUSS IS SIMPLY SUPPORTED AT JOINTS M AND E. Determine the stress at member CD if Pu = 18.375 Kips, the area is 23 in?. Answer your problem with the given unit ksi. Pu Pu Pu Pu Pu Pu Pu * (a. 10' - R it J I H G F H (n 10' - KI K Ru 8@10'=80'
The steel framework shown below is used to support a 4-inch thick reinforced concrete slab and carries a uniform Live Load of 400 lb/ft2. The Density of Reinforced Concrete=150 lb/ft³. Sketch the loading that acts along members BE and FED. C A -b- B F 02 PROB_001-002 Carte Cake E a Given: a=6 ft, b=12 ft, 0 D a
A steel beam is subjected to a uniform load with length of 8m. Assume that the beam is simply supported. Use Fy= 248 Mpa. Properties of W-shape beam d=229 mm bf=210 mm rf=23.7 mm Tu-14.50 mm kdes=33. 80mm ry=53.80 mm Ix=113 x 10^6 mm^4 Iy-36.9 x 10^6 mm^4 Sx-990 x 10^3 mm^3 Zx 1150 x 10^3 mm^3 J-2100 x 10^3 mm^4 Cu-387 x 10^9 mm^6 What is the nominal shear strength capacity of the section (in kN)?
DETERMINE FORCE (N) OF MEMBER EG in the truss shown. F1 = 214 N %D F2 = 876 N %3D F3 = 435 N a = 38 degree X = 15 m. **Note: for compression, include a negative sign (- ) and for tension, type your answer as is. Input your answer in two (2) decimal places only without the unit. В H A C E G F1 F2 F3