Find the centroid first then after you find the second moment of area using the centroid in a tabular form Determine the second moment of the shaded area w.r.t (a) the x-axis (b) the y-axis(dimensions in cm)y636Ans: (a) 648 cm4 (b) 1971 cm4

Answered: Image /qna-images/answer/dcf3d877-5ce6-43ad-9281-0119edd2b06a.jpg

Answered: Determine the second moment of the…

Determine the second moment of the shaded area w.r.t (a) the x-axis (b) the y-axis (dimensions in cm) y 6 3 6 Ans: (a) 648 cm4 (b) 1971 cm4

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The 1.5-in.-diameter shaft shown in Fig. 5-9a is supported by two bearings and is subjected to three...

Q: Problem 1-find the reactions and complete the load diagram. Draw the shear force and bending moment ...

A: ASKED: To determine the support reactions and draw the shear and moment diagram. The support react...

Q: 1. Oil that has a density of 880 kg/m flows under a head of 30 m. The pipe that the oil flows throug...

A: We have to determine the flow in dm3/sec as per the given data in the question and we have to also c...

Q: Compute the nominal compressive strength of a HSS 10 x 8 x 3/16. The length is 3.7m with one end pin...

A: ASKED: To compute the nominal compressive strength of given steel compression member. Given, Steel...

Q: A skateboarder rides down a parabolic half-pipe. The profile of the half- pipe is y = x2/80 m, where...

A: To find the magnitude of acceleration at point A

Q: 5. For the bridge beam shown, determine the shear at point B of the beam due to the wheel loads when...

Q: draw

Q: A boat in rectangular shape has the following dimension: 5m long, 8m wide, and 5m deep.- It is subme...

Q: yrum n=0.025 5 m 12 m

Q: 1) A six-lane highway (3 lanes in each direction) is to be designed to replace an existing highway. ...

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since t...

Q: For the beam loaded as shown in the figure below, determine the following unknown using any geometri...

Q: A 6-h stom had 6 cm of rainfall and the resulting runoff was 3.0 cm. If the g-index remains at the s...

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of understandin...

Q: If no Geotechnical data is available for a building to be constructed in Iba, Zambales, the soil pro...

Q: q2 w1 94 w3 w5 3 m x 5 = 15 m %3D

Q: The big cylinder can with one closed end is submerged under water with air. The cylinder has dimensi...

A: ASKED: To compute the depth upto which the cylinder is submerged. Given, Height of the cylinder (H...

Q: Draw the B.M.D for the following

A: The diagram given in the question is as follows:

Q: MAKE 1 PROBLEM (QUESTION AND SOLUTION) REGARDING TRAVERSE SURVEY IN THE FUNDAMENTALS OF SURVEYING. I...

A: Question: The following interior angles were measured in a closed traverse. The bearing of line AB w...

Q: (Problem 5.156 from the text book) Draw the shear and bending-moment diagrams for the beam and loadi...

Q: A carpentry crew consists of one foreperson, four carpenters, and four laborers. The bare hourly wag...

A: ASKED: To compute the weighted average burdened wage rate for the crew. Given, Class Bare hourl...

Q: The following stress element represents the stress state at point A of the structure in the figure b...

Q: A hydrographic survey was conducted on a reservoir to determine its capacity by contour method. The ...

A: Sounding is a method of determination of RL of a point under the water surface.

Q: 3. The temperature of an iron bar is 36°F. It is placed in an oven, after 1 and 2 minutes, respectiv...

Q: KP s over a component of an aircraft that can be modeled of 8° that is aligned with the flow, the fl...

A: Data given M1 =2P1 =80 KPaT1 =30° c =303° Kflows turning angle θ= 4° from θ-β-M relation tan...

Q: re attached to a circular shaft and transmit the torques shown in the figure. The allowable shear st...

A: TAB=-8000TBC=-8000+19000=11000TCD=-8000+19000-4000=7000Max torque Tmax=11000lb-inτ=16Tπd3d3=1611000π...

Q: Which information sources can be used for recommending improvements in construction methodology of t...

A: Construction Methodology : 1. Construction methodology or project execution methodology is referred ...

Q: Which is not a sources for Highway Funds? Gasoline Tax * Adopt A Highway Program Tolls Traffic Fines...

A: Solution- General Income Tax is not Highway Funds.

Q: Notice in the figure, a free jet falling from a nozzle of triangular cross section. After it has fal...

Q: 2-032 Ф12 2-020 400 mm -175mm- B SECTION 1525 mm ACANTILEVER BEAM ELEVATION B

A: Given Fc 28 MPa Fy 415 mpa Fyt 275 mpa Width 175 mm Depth 400- 60 = 340 mm Effective cover 60mm ...

Q: 3. Draw the internal force diagrams (and include all significant values) for the following system. 3...

Q: 2. For the cantilever beam shown below, calculate the maximum bending tension and compression stress...

A: To Find :- maximum bending tension & compression stresses

Q: K 5 m G 40 kN 40 kN 40 kN 40 kN 40 kN -6 at 5 m 30 m- (Ans: Fcj=28.28kN (C); Fij=160kN(C) ; Fcd=180k...

Q: The rate of evaporation is mainly dependent on the following except for A wind speed B air quality C...

A: The rate of evaporation is directly proportional to the wind speed, more the wind speed more will be...

Q: 1. Find the resultant using (a) the head-to-tail method, and (b) the parallelogram method: A clever ...

A: D1 = 347m D2 = 764m D3 = 465m

Q: From the given figure, determine the following characteristics of the resultant: (a) magnitude of R,...

A: Given Data: The length AC is given as 6 ft. To Determine: (a) The magnitude of R. (b) orientation ...

Q: The diameter of a steel tank is 3.5 meters, and the wall thickness is 6 millimeters. The tank stands...

Q: 1. For the beam shown below, draw shear and moment diagrams. 4000 lb 600 lb/ft A 2' – 0" - 6' – 0" 4...

Q: What concetrated load can be carried by a 250 x 250 mm beam if the length is 2000 mm and the modulus...

Q: AREA OF RANGE CROSS-SECTION. Sounding were taken along a 38-m long range across a lake ( see accompa...

Q: The magnitude and direction of the reactions at support B. EM„A =0 -R, × L+| q(x)·xdx = 0 %3D R, =-q...

Q: If the wind velocity at a height of 2 m above ground is 5.0 kmph, its value at a height of 9 m above...

A: U2 = 5.0 Kmphh2 = 2mh9 = 9mU9 = to find

Q: The discharge in an open trapezoidal channel was measured by slope area method. Depth of water = 2.5...

Q: The true azimuth of a line measured from south is 154°30'. If the magnetic declination within the lo...

Q: 400 gm/lit. solution of commor charged into a stream at a cons lit./sec. At a downstream section

Q: (in psi) if the cross section has the dimensions indicated and the moment of inert stress cannot exc...

A: solution of above problem is below:

Q: Question 5 In the acquisition of specific property for highway projects, the public entity (i.e. NJD...

A: The National Highways Development Project is a project to upgrade, rehabilitate and widen major high...

Q: The Atterberg limits for the soil are LL = 105 and PL =85. What is the PI? %3D

Q: In a highway construction site, excavation with sloping is planned for soils with an unconfined comp...

A: According to Occupational Safety and Health Administration, soil are classified into 4 categories ba...

Q: boloid in meters when its rotatin

Q: 3.6-5 Choose a pipe to be used as a tension member to resist a service dead load of 10 kips and a se...

Q: Two bodies A and B, weighing 400 lbs and 300 lbs, respectively, are cor ft long and of negligible we...

Concept explainers

Moments

There are various practical applications of the concept of moments, like a rotation of the crank due to linear motion of the piston, the moment of inertia and its use in designing beams and columns, bending moment concept, torque, twisting moment, etc.

Question

100%

Find the centroid first then after you find the second moment of area using the centroid in a tabular form

Determine the second moment of the shaded area w.r.t (a) the x-axis (b) the y-axis
(dimensions in cm)
y
6
3
6
Ans: (a) 648 cm4 (b) 1971 cm4

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the section shown, find the centroid of the shaded area with respect to the XY axis. y 14 Diameter 10 10 8. - 10 14 %3D YG%3=
Problem 2: Determine the centroid X-bar with respect to Y-axis 150 mm 15 mm C 150 mn -15 mm 15 mm 100 mm Drob. 9-61
y 100 mm 140 mm 50 mm 140 mm -200 mm x
Determine the distance H from the upper surface of the symmetric double-T beam cross section to the location of the centroid. 350 14 -75 H 215 14 Dimensions in millimeters Answer: H = mm %3D
Given the two orthogonal projections of the object (top view and front view), identify the third corresponding view (side view) O O C O C (a) 4 (b) 2 X (C) 3 (d) 1 (e) 5 ? 1 2 N 4 3 5
Determine the x- and y-coordinates of the centroid of the shaded area. Input values in two (2) decimal places only without the unit. X-bar Y-bar -r= 16 in. a = 8 in. a = 8 in.
Problem 3: Locate the centroid x of the area. y = -b-
Locate the centroid X of the area in Figure 7. (a) 62.11 cm (b) 70 cm (c) 65.20 cm (d) 73.25 cm 60 cm y 30 cm 80 cm Figure 7. A shape in x-y plane X
Determine the x-coordinate of the centroid of the shaded area by integration. 1 12 11 Answer: x= 15 -x
2. Locate the centroid (x, y) of the cross-sectional area. sin 2 in 0.6
4) Calculate the location of the centroid of area (X,Y) and the moment of inertia about the center of area for the shape shown below. X- B
36 - Find the center of gravity M (x,y,z) of the three-dimensional homogeneous ABCD wire in the figure by using the coordinate set. The dimensions of the wire are a= 20 cm, b= 30 cm. Which of the following is the correct coordinate of the homogeneous wire in the y-axis?A) 12.33B) 15.29C) 14.43D) 13.71E) 17.14