QUESTION 3 Figure Q3 shows a steel beam structure, which is pinned, roller and fixed supported at A, C and D respectively. The beam is subjected to the concentrated load at B and uniform load at D. The relative plastic moments of resistance for all spans are shown in the figure. a) Draw the mode of failure mechanism for the beam structure. (CO2, C3, PO2, WP1) Marks b) Determine the maximum plastic moment for the beam structure. (CO3, C4, PO2, WP1) 10KN 15KN/m A 2Mp C 3Mp 4m 4m 3m 3m Figure Q3

QUESTION 3 Figure Q3 shows a steel beam structure, which is pinned, roller and fixed supported at A, C and D respectively. The beam is subjected to the concentrated load at B and uniform load at D. The relative plastic moments of resistance for all spans are shown in the figure. a) Draw the mode of failure mechanism for the beam structure. (CO2, C3, PO2, WP1) Marks b) Determine the maximum plastic moment for the beam structure. (CO3, C4, PO2, WP1) 10KN 15KN/m A 2Mp C 3Mp 4m 4m 3m 3m Figure Q3

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 175 MPa in rod AB and 150 MPa in rod BC, determine the smallest allowable values of d1 and d2. 300 mm 250 mm A B C -d₁ 40 kN -d₂. 30 kN
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
HW:B Find the max Value of e) that canbe aPPIied on the Catilever beam Shown in figure , knowing that the max Gombined stresses will not exceed(22.67 Ma)in tension and (17.33 Ma) in wmPression? Ans/ Prnx = 25 W 450mm 150mm N.A Son S0mm fig. (B)
Q.2) A rigid bar ACD is supported by two circular steel (E= 30x10° psi) rods AB & DE and a pin support at C. Bar ACD was horizontal prior to the application of load P. The tensile strain measured in rod AB after the application of the load is ɛ1= 0.003. Determine the rotation 0 of the bar ACD and the normal strain in rod DE. Also calculate the value of load P for these deformations. The diameters of rod AB and DE are 1.5 in. and 2 in, respectively. P - 4 ft 4 ft- 6 ft A Rigid (2) 6 ft 8 ft (1) E В
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
Determine the normal strain EAB in wire AB.
A thin polymer plate PQR is deformed so that corner Q is displaced downward by a distance L = 1.45 mm to new position Q' as shown. Determine the shear strain at Q' associated with the two edges (PQ and QR). 120 mm 480 mm. P R 240 mm -2692 μrad -3352 μrad O-4917 prad -3610 μrad O-2921 urad Q 'Q' X
5) Match the beam bending stress profile for design to the correct cross section shown below: "但"g (1) (2) (3) (A) (B) P (C)
HW:B Find the max Value of e) that canbe aPPIied on the Catilever beam Shown in figure , knowing that the max Gombined stresses will not exceed(22.67 Ma)in tension and (17.33 Ma) in wmPression? Ans/ Prnx= 25 W 450mm 150mm N.A 1 2 S0mm fig. (B)
Q1 A truss system is shown in Figure Q1. It is loaded at joints D and E as shown. The truss members are to be manufactured from Aluminium Alloy cylindrical bar with a tensile yield stress of 300 MPa, a compressive yield stress of 200 MPa, and Young's Modulus of 70 GPa. 1.5m 1.5m A B 4001 10 KN 3m Fig. Q1 E 水 20 KN 1.5m D ➜ (a) Show that the truss system can be described as statically determinate. (b) Draw a Free Body Diagram of the truss and determine the reactions at the supports. (c) Use the METHOD OF JOINTS to determine the load in each member of the truss, indicating whether they are tensile or compressive.
The member shown has a rectangular cross section, determine the state of stress that loading produces at point C. 1.5m 1c T 250mm 2.5m 125mm 1.5m 50mm 4m + 2m 50kN/m
1 - Determine the maximum shearing stress in the beam for the loading shown in the figure. The same beam cross-section was used in HW 5. 2 KN 0.5m- 1KN - 0.5m 107 30 30 T dimensions in mm lok beam cross-section