solve show full solutions for given answers Figure P18.14 shows a 1000-kg mass being lowered by a cable at a uniformrate of 4 m/s from a drum of 550-mm diameter weighing 2.5 kN and havinga 250-mm radius of gyration.(a) What is the kinetic energy in the system?(b) The uniform rate of descent is maintained by a brake on the drumwhich applies a torque of 2698 N m. What additional brake torque isrequired to bring the system to rest in 0.60 s?4m/s1000 kg(d)FIGURE P18.14Ans.Part a.) 9685 JPart b.) 2219 Nm

Answered: Figure P18.14 shows a 1000-kg mass…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A min cage of mass 4t is to be raised with an acceleration of 1.5m/s2 by a cable passing over a hoist drum of 1.5m diameter. What is the power required when the load has reached a velocity of 6m/s, neglecting the inertia of the drum and weight of the cable, but allowing for bearing friction torque of 3kN at the drum? What is the power required at a uniform velocity of 6m/s
A Mine cage of mass 4t is to be raised with an acceleration of 1.5 m/s by a rope passing over a hoist drum of 1.5 m diameter. What is the power required when the load has reached a velocity of 6 m/s, neglecting the inertia of of the drum and the weight of the rope, but allowing for a bearing friction torque of 3kN m at the drum. What is the power required at a uniform velocity of 6 m/s
A uniform cylindrical turntable of radius 1.9 m and mass 30.0kg rotates counterclockwise in a horizontal plane with an initial angular speed of 4pi rad/s. The fixed turntable bearing is frictionless. A lump of clay of mass 2.25kg and negligible size is dropped onto the turntable from a small distance above it and immediately sticks to the turntable at a point 1.80m to the east of the axis. A. Find the final angular speed of the clay and turntable. B. Is the mechanical energy of the turntable-clay system constant in this process? C. Is the momentum of the system constant in this process? Explain your answer.
The system shown below is made up of two pulleys attached to the same shaft, with radii ri and re of 0.29 mm and 0.43 mm, respectively. The total mass of the pulley system is 14 kg and its turning radius is 0.26 mm from its center. The mass of block A is 9 kg and the mass of block B is 2 kg. If the coefficient of kinetic friction between block B and the floor is 0.2, find the angular acceleration of the pulley.
A flywheel is a mechanical device used to store rotational kinetic energy for later use. Consider a flywheel in the form of a uniform solid cylinder rotating around its axis, with moment of inertia I = 1/2 mr2. 1) Consider a scenario in which the flywheel described in part (a) (r1 = 0.55 m, mass m1 = 16 kg, v = 45 m/s at the rim) is spinning freely at its maximum speed, when a second flywheel of radius r2 = 2.8 m and mass m2 = 11 kg is coaxially dropped from rest onto it and sticks to it, so that they then rotate together as a single body. Calculate the energy, in joules, that is now stored in the wheel. 2) Return now to the flywheel of part (a), with mass m1, radius r1, and speed v at its rim. Imagine the flywheel delivers one third of its stored kinetic energy to car, initially at rest, leaving it with a speed vcar. Enter an expression for the mass of the car, in terms of the quantities defined here.
A box of mass m = 0.7 kg is attached to a rope which is wrapped around a physical pulley with a radius of R = 10.2 cm and a rotational inertia of I = 0.075 kg·m2. When the box is released it starts to fall down with a constant acceleration and, at the same time, the pulley starts to spin up, see the picture below. Assuming that the pulley is frictionless, what is the magnitude of the box's acceleration and what is the tension in the rope? The acceleration of the box, a ? The tension in the rope, T? If the box starts from rest and traveled downwards a distance of h = 28 cm, what is the speed of the box and what is the angular velocity of the pulley? The speed of the box, v =? The angular velocity of the pulley, ω? -------------------------------------------------------------- A Merry Go Round carousel has a radius of R = 2.4 m and a rotational inertia of I = 695 kg·m2. A 75‑kg student is on the carousel at the midpoint between the carousel's center and the rim (at R/2 distance from…
A box of mass 25.0 kg is connected to another box of mass 15.0 kg by an inextensible string of negligible mass. The string is passed over a frictionless pulley of mass 8.0 kg and radius 30.0 cm. The pulley is a solid disk that is free to rotate about the horizontal axis passing through its centre. Initially, the 25.0 kg mass is 5.00 m above the floor, and the masses are at rest. If the masses are released, what is the time it takes for the 25.0 kg mass to hit the floor?
A flywheel of mass 125kg and radius of gyration 150mm is accelerated from rest to a speed of 1180rpm whilst making 500 revolutions. The motion is resisted by a friction torque of 2.5Nm. Determine the work done and the maximum power developed by the driving motor.
The crude-oil pumping rig shown is driven at 20 rpm. The inside diameter of the well pipe is 2 in., and the diameter of the pump rod is 0.75 in. The length of the pump rod and the length of the column of oil lifted during the stroke are essentially the same, and equal to 6000 ft. During the downward stroke, a valve at the lower end of the pump rod opens to let a quantity of oil into the well pipe, and he column of oil is then lifted to obtain a discharge into the connecting pipeline. Thus, the amount of oil pumped in a given time depends upon the stroke of the lower end of the pump rod. Knowing that the upper end of the rod at D is essentially sinusoidal with a stroke of 45 in. and the specific weight of crude oil is 56.2 lb/ft3 determine (a) the output of the well in ft3. /min if the shaft is rigid, (b ) the output of the well in ft3 /min if the stiffness of the rod is 2210 N/m, the equivalent mass of the oil and shaft is 290 kg, and damping is negligible.
In case of a single cylinder double acting steam engine, 180 kW power is being developed at a mean speed of 120 r.p.m. The coefficient of fluctuation of energy is 0.12. The fluctuation of speed is ± 2% of mean speed. The flywheel rim has mean diameter of 2 metre. The hub and spokes of the flywheel provide 8% of the rotational inertia of the flywheel. If the density of the flywheel material is 7200 kg/m3, determine the mass and cross-sectional area of the flywheel rim.
A wheel of mass m, radius r and radius of gyration k is rolling along a horizontal road with hub velocity v in the +ve x direction. Brakes are applied to the wheel, providing a torque of -M, slowing the vehicle to rest. Assuming that the wheel rolls without slipping and the hub position starts at x=0, where m = 10 kg, r = 0.85 m, k = 0.595 m, v = 5m/s, M = 21 Nm, g = 9.81 m/s^2 a) Find the constant acceleration, (ax) of the wheel hub b) Find the minimum static coefficient of friction (mu) between the road and the wheel c) Find the stopping distance (smax) and time (tmax)
A. A motorcycle and rider have a combined mass of 350kg. The wheels each have a mass of 20kg, diameter of 500mm and radius of gyration of 200mm. The rider accelerates uniformly from 5m/s to 25m/s over a distance of 100m, whilst climbing a hill of slope 1 in 20. The average resistance to motion, including drag, is 105 N. 1. Determine the total work done as the motorcycle ascends the incline. 2. Calculate the amount of power developed during the climb. B. At another point in its journey, the motorcycle and rider travel at 80 km/h around a left-hand bend of radius 30m. Calculate: 1. The angular velocity of each of the wheels. 2. The moment of inertia of each wheel. 3. The magnitude and effect of the gyroscopic torque produced on the bike.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS