Find the resultant force and the angles the resultant force makes with all three axes. Assume values of x and y, based on other dimensions. 16 m 18 m 600 N 400 N 24 m 2 800 N A B

Q: Model the arm ABC as a single rigid body. Its mass is 320 kg, and the moment of inertia about its…

A: The mass of the rigid body is M=320 kg. The moment of inertia about the center of mass of I=390…

Q: In the project, the theoretical methods will be used to construct the property tables for ammonia…

A: To construct the property tables for ammonia using the Van der Waals equation of state, several…

Q: A 6 m- 4 kN 30°, -2m B 30°

A: Note:- As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: Determine the components of reaction at the ball-and-socket joint A and the tension in the…

A: please refer handwritten solution

Q: 1) Use the method of PINS to determine the true magnitude and direction of the forces in all the…

A: please refer handwritten solution

Q: An airplane is flying at an altitude of 20,000 m at an equivalent airspeed of 350 m/s. Find the…

A:

Q: a contractor want to invest his money in on of project A or B if you know that the interest rate is…

A: The Net Present Worth (NPW) method, also known as Net Present Value (NPV) method, represents the…

Q: In a certain industrial process, oil of density p flows through the inclined pipe in the figure…

A: Here, the given pipe flow is steady , U tube manometer is connected between section (1) and (2) .The…

Q: Each of the 4-lb spheres is rigidly attached to the crossbar frame as shown in (Figure 1). The frame…

A: The final speed of the spheres. Given: The mass of the spheres is m=432.2 slug. the length of the…

Q: Angle of twist at E, Øit Torque at F is 107 Nm, G-210 GPa and J-79531 88 mm Power at F= 2000 MW…

A: Given Data :- Power at F = 2000 MW                G =210 GPa  = 210×103 MPa  Torque at F = 107 Nm…

Q: Newton 's law of cooling describes the temperature T of a body cooling down to the surrounding…

A: Temperature of the body is T Surrounding temperature is To The equation given is: →dTdt=-kT-To Where…

Q: 2. [Relative Motion Analysis using Rotating Axes] At the instant shown the truck is moving toward…

A: The speed of the truck is vtruck=1.5i⇀ m/s. The acceleration of the truck is atruck =0.5i⇀ m/s2 The…

Q: Draw the free-body diagram of each object and determine the components of the support reactions.

A: Since you have posted multiple questions, we will provide the solutiononly to the first question as…

Q: how do you find the composition based on the tempratures from the phase diagram, like the temp are…

A: In the cooling curve, the changes take place at around 160 and 130 degree temperature. because in…

Q: Determine all the member forces of the loaded simple truss, shown on the figure, assuming a=2 m,…

A: Apply force equilibrium in x-direction. ∑Fx=0Ax+Fcos60°=0Ax=-23cos60°=-1.732 N Apply moment…

Q: A mercury manometer installed across an orifice meter (diameter = 1.2 cm) in a horizontal pipe…

A: Given: d = 1.2 cm = 0.012 mD = 2.35 cm = 0.0235 mh = 12 cm = 0.12 m Taking the density of mercury as…

Q: Ross and Rachel are fighting if they were on a break. Ross is trying to get his stuff weighing 150.…

A:

Q: 1. A circular cam is rotating clockwise about O with a constant c. Determine the velocity and…

A: Given data To determine the acceleration of the follower as function of θ

Q: Calculate the drag and lift force on the airfoil by numerically evaluating the integrals dYu dx Fx =…

A: The central difference for the numerical derivatives are dYudx=Yui+1…

Q: Consider a piston-cylinder device which initially contains 1.4 kg of saturated liquid water at…

A: Given:Initial state of water, m=1.4 kg, T1=220oC, Saturated liquidFinal state volume, V2=4×V1Quality…

Q: 3) Find the factors of safety, based upon the maximum shear stress (MSS) theory and the…

A:

Q: n aero engine has a tub diameter of 0.36 and tip diameter of 0.70. What is the height of the blades

A: To find the radius of the blades, we need to first calculate the common diameter of the blades. we…

Q: The figure shows a schematic for a hydraulic jack. Lever AC is hinged at A. The upper valve at D is…

A:

Q: 4. A diesel engine with the following specifications, 12 cylinders, 0.75 m x 0.95 m, four stroke…

A: Given:Number of cylinders, x=12Bore, D=0.75 mStroke, L=0.95 mSpecific fuel consumption, SFC=0.75…

Q: PROBLEM 3 For the mechanism, shown on the figure 1-2 m/s, q=7 m/s². AB-04 m. Determine: a) linear…

A: Given Velocity, v = 2 m/s   Acceleration, a1 = 7 m/s2 Find   Linear velocity and acceleration of the…

Q: QUESTION 2 The shaft carries four masses A, B C and D respectively. Magnitude of masses A and D…

A: To Find- The magnitude and position of the masses B and C relative to the masses A in order to…

Q: A steam turbine receives steam from a boiler at 8 MPa and 480oC. After some time, a third of the…

A:

Q: Please only answer question 4 Parts C and D

A: A thermodynamic cycle called the vapor refrigeration cycle is employed in refrigeration systems to…

Q: A dam with triangular cross section holds back a body of water. The dam has height h. The dam is…

A: The specific gravity of the triangular section is s.g=1.3

Q: A steam turbine receives steam from a boiler at 8 MPa and 4800C. After some time, a third of the…

A: Boiler exit condition @ P[1] = 8000[kPa], T[1] = 480[C] First extraction @ P[2] = 6500[kPa] First…

Q: Locate the centroid of the shaded area. Set b = 0.30 a. y b x=a(1-²²) a x

A:

Q: i still dont think i am getting the full working how you get to 0.32, am going to need to see the…

A: Given Data

Q: One Question more for the solution above :  Calculate the location of the normal shock inside the…

A: Given data Exit Area ratio. AeAt=2.1931 where At is the area of the throat Ae is the exit area of…

Q: Show explicitly that the wave function, y(x, t) = A cos(kx - wt) satisfies the wave equation,…

A: yx,t=Acoskx-ωt Write the partial derivative of y with respect to x.…

Q: P1 10 Boiler 12. P13 8200 PIV 14 16 Closed Closed FWHI FWHII 8 T13 350 13 PIII High-P Turbine Open…

A: Find

Q: 30kNLIm, 60kN/m 3m 2m 10kN 4 Im Hinge B 2m C 2m D 4m 5kN/m E

A:

Q: The light bracket ABC is freely hinged at A and is constrained by the fixed pin in the smooth slot…

A:

Q: PROBLEM 1 a. Determine the equations for slope and deflection of the beam by direct integration…

A:

Q: Two smooth disks A and B each have a mass of 0.5 kg. Both disks are moving with the velocities shown…

A:

Q: An amount of gas inside an insulated vessel contained 45000J of internal energy. The gas expands…

A:

Q: A curved gate in the shape of the circular arc was used to hold oil and water in the container…

A: Specific gravity of the oil=0.86  So the density of the oil→ρo=0.86×1000=860 Kg/m3 Equivalent height…

Q: The 5-m wide sluice gate “ab” shown, tangent to the vertical wall at “a”, holds back water. The…

A: Width of the gate→w=5 m Radius of the cylindrical part→R=4 m Angle made by the the gate the center…

Q: So, what is the magnitud and direction from E to D. ?

A: FBE=0 FAE=288.675 lb (Compressive)

Q: Taking the recent World Energy Council and United Nations resource-base figures for the total amount…

A: Total amount of fossil energy in the ground worldwide=356000 quads usage grows=3% per year Primary…

Q: 9-15. Determine the vertical displacement of joint A. Assume the members are pin connected at their…

A:

Q: A centrifugal pump having an overall efficiency of 75%, delivers 1850 liters of water per minute to…

A: Given:Overall efficiency of the pump, η=75 %Water flow rate, Q=1850 L/min=1850×10-360m3/sHeight of…

Q: The sign has a mass of 100 kg with a center of mass at G. Determine the components of the reaction…

A: Write the point vectors for each point. A=0, 0, -0.5B=0, 2, 0C=1, 0, 2D=-2, 0, 1 Write the vectors…

Q: For a short time, the 400-kg roller-coaster car with passengers is travelling along the spiral track…

A: mass of the car, m =400 kg   the radius of the track, r=10 m   θ=0.2t   z=-0.3t   To find components…

Q: A tent peg made from a circular steel rod is embedded in the ground as shown in the figure below.…

A: Given data: Overall length of the peg =150 mm=0.150 m embedded length of the peg L=117 mm=0.117 m…

Q: Locate the centroid of the figures shown. Calculate the moment of inertia along X and Y. All…

A:

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.