From the given truss shown: F= (0.25)(Birth month)(birthdate) Newton Example: if your birthday is December 28 you F= (0.25)(12)(28)= 84 N (a) What is your birthday (Month and Day) (b) What is the value of your F? (c) Calculate the reaction at the support. (d) Using the METHOD OF JOINTS, determine all the forces carried by each member of the truss, state whether the members is under tension or compression. Make a summary table of the forces and orientation carried by each member. 3 m 6 m

From the given truss shown: F= (0.25)(Birth month)(birthdate) Newton Example: if your birthday is December 28 you F= (0.25)(12)(28)= 84 N (a) What is your birthday (Month and Day) (b) What is the value of your F? (c) Calculate the reaction at the support. (d) Using the METHOD OF JOINTS, determine all the forces carried by each member of the truss, state whether the members is under tension or compression. Make a summary table of the forces and orientation carried by each member. 3 m 6 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the truss shown in the following figure, the temperature of member BC is raised by 140 °C, and member BD is raised by 160 °C. EA=300000 N for all members and a=1/75000 1/°C. Use the stiffness method to do the following: A b) Ay II C Part 1. Calculate the displacements at the joints: a) A₂ = c) B₂ = d) By = e) C₁ = 3112 mm mm mm mm mm -5m- Part 2. Calculate the force in each member: a) NAB= N b) NAC = N c) NBD = N d) NBC = N e) NCD = N f) NAD = N B D 5m
For the truss shown in the following figure, the temperature of member BC is raised by 110 °C, and member BD is raised by 70 °C. EA=300000 N for all members and a=1/75000 1/°C. Use the stiffness method to do the following: b) Ay = c) B₂ A | C ΤΙΣ Part 1. Calculate the displacements at the joints: a) Az = d) By = e) C₂ mm mm mm mm mm Part 2. Calculate the force in each member: a) NAB = b) NAC = c) NBD = d) NBC = e) Ncp = f) NAD = 5 m N N N N N N B D 5 m
4. The structure in the figure is composed of two rigid bars (AB and CD) and two vertical rods made of aluminum and steel. All connections are pin joints. Determine the maximum force P that can be applied to the structure if the deformation of the Aluminum rod is limited to 6 mm. Neglect the weights of the members. Aluminum 2 m A = 300 mm E= 70 GPa Steel A = 500 mm? 2 m E= 200 GPa 3 m 3 m
D 140 mm in the trusses analyies experiment we got the strain Reading as, B Loaden) 5train AB strain AC 5train BC (EM) (EM) (EM) O 469 1117 1116 50 465 1115 1126 100 463 1110 1131 150 458 1095 1139 200 453 1085 250 450 1080 calcute the force in each member; F= πTd²x ExE 4 d = 5.985mm E = 210 GN/m² B W с 1148 t 155
The cantilever beam is supported by a fixed support at A, and subjected to the force F-470 lb and the couple M = 3210 ft-lb. Draw the shear force and bending moment diagrams (in your homework documentation) and determine the equations for V(x) and M(x). Take z = 0 at point A. 2013 Michael Swanbom F₁ (CC) a b BY NC SA a Support Reactions The force reaction at A is The couple moment reaction at A is Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value 4 ft 3.2 ft Shear Force and Bending Moment Equations In section AB: V(x)= In section BC: V(x)= B lb (take up as positive). lb and 'M(x)= M lb and 'M(x)= b- C ft-lb (take counterclockwise as positive). ft-lb. ft-lb.
In the figure, the ac element is rigid and is held with the bars AB, CD and EF, each of which has a cross-section of 145 mm ^ 2, without a blank and without tension. The AB bar can be changed with a screw mechanism over 0.75. The step of the screw in a full turn is 1.5 mm. If the screw is rotated 1.5 steps in the direction of shortening the length of the EF rod, what is the value of the force that will occur on the EF rod? Take the elastise modulus 210 GPa for all bars
At a temperature of 53°F, a 0.1 in. gap exists between the ends of the two bars shown. Bar (1) is an aluminum alloy [a= 12.7 x 10-6/°F] and bar (2) is stainless steel [a= 10.4 x 10-6/°F]. The supports at A and C are rigid. Determine the lowest temperature at which the two bars contact each other. Assume L₁ = 40 in., L₂ = 57 in. (1) B A L₁ Answer: Final temperature = i bo L2 °F.
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 519 mm2; link CE is made of steel (E = 200 GPa) and has a cross-sectional area of 619 mm?. For the 41 kN force shown, determine the deflection of B (mm) *deflection should have a negative sign if compression and positive if tension. Also, your final answer should have two decimal places 04 m 0.3 m E 0.4 m 0.2 m
A two member truss ABC is shown in the figure. The force (in kN) transmitted in member AB is - A 11 0.5 m 17 1pc C 1 m B 10 kN
The following truss system is Pin Supported at Joint C and Roller Supported at Joint E. Joint B is subjected to a Point Load of 1000 Newton. Joint A is subjected to a Point Load of 1500 Newton. Show the values of F at the beginning of the solution as well as the calculation steps and answer in the unit Newton. Using the Method of Joint, determine the forces in each member of the trusses shown in the following figure. 1500N 1000 N 12m 12m A 8 m 5 m 61 D 12m 6 m Identify the force acting in each member of the trusses shown.
The following truss system is Pin Supported at Joint C and Roller Supported at Joint E. Joint B is subjected to a Point Load of 1000 Newton. Joint A is subjected to a Point Load of 1500 Newton. Show the values of F at the beginning of the solution as well as the calculation steps and answer in the unit Newton. Using the Method of Joint, determine the forces in each member of the trusses shown in the following figure. 1500N 1000 N 12m 12m A 8 m 6 m D 12m 6 m Check the stability of the truss system. Elaborate what “Statically Determinate Truss" implies.
a 200-kg mass M is attached to a pin at C as shown Determine the forces acting in the members AC and BC