Name SURNAME: Student ID: QUESTION 9 The AE cable carrying the concentrated loads is attached to the rod EN, which has two ends of the hinges. The rod EN stands vertically with the cable EG. a= 2 m, b = 8 m, c = 4 m, d = 6 m, P = 20 kN. a) Find the reaction forces at the pins A and G, the force on the rod EN. Draw all the required free body diagrams. b) Find the vertical distances of YAB and yAD- Draw all the required free body diagrams. SOLUTION B a P P E P b-b-*c*c*

Name SURNAME: Student ID: QUESTION 9 The AE cable carrying the concentrated loads is attached to the rod EN, which has two ends of the hinges. The rod EN stands vertically with the cable EG. a= 2 m, b = 8 m, c = 4 m, d = 6 m, P = 20 kN. a) Find the reaction forces at the pins A and G, the force on the rod EN. Draw all the required free body diagrams. b) Find the vertical distances of YAB and yAD- Draw all the required free body diagrams. SOLUTION B a P P E P b-b-cc*

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

STATICS OF RIGID BODIES Determine a. The component of the force F acting along the cable AC b. The angle the force F makes with cable AC.
Determine the tension, T, in the cable support which is attached at point B, and also the Cartesian components of the reaction-force vector, A, which acts at the pin support, point A. (A FBD is required for this problem.) -0.1 m 0.5 m 0.75 m 0.75 m- 600 N
The rigid beam is supported by a pin support at A and steel wires BD and CE (E-200GPA). The steel wires are 1cm in diameter. If the load P is 5kN and the weight of the beam is neglected, solve the tension at wire BD. E 4 m 3 m 2 m 2 m O 1.95kN O 1.64kN O 0.91kN O 1.29KN o o oO
Classify the structure shown as statically determinate or statically indeterminate. If statically indeterminate, state the number of degrees of indeterminacy. There are pins at A, E, and F and rollers at B, C, and D. 80 k 50 k 40 k JE |F 20 ft'20 ft - 40 ft----30 ft+-40 ft→+-30 ft ---| 10 ft 10 ft
The bracket ABC can be supported in the eight different ways shown.All connections consist of smooth pins, rollers, or short links. In each case, determine whether (a) the plate is completely, partially,or improperly constrained, (b) the reactions are statically determinate or indeterminate, (c) the equilibrium of the plate is maintained in the position shown. Also, wherever possible, compute the reactions assuming that the magnitude of the force P is 100 lb.
HW.: determine the forces in all cables C D B 30° 45° A 200 N 500 N
MULTIPLE CHOICES AND SHOW YOUR COMPLETE SOLUTION: 2. Draw the influence line diagram of the given bridge truss system below for its member BC and HI if the loaded chord is member Cl? a. The maximum positive or negative ordinate for the ILD of member BC.2 o -1.2 UNITS o 1.2 UNITS o -1.04 UNITS o 1.04 UNITS b. The maximum positive or negative ordinate for the ILD of member Hl. ? o -1.2 UNITS o 1.2 UNITS o 1.04 UNITS o 1.05 UNITS c. If the bridge truss system is carrying a uniform deadload of 10 kn/m and a moving live load of 13 kn/m with two concentrated loads of 75 kn and 50 kn that is 2m apart. Determine the equivalent bar force for member BC and indicate whether it is in compression or tension. o -558 KN, C o 558 KN, T o 585 KN, T o -585 KN, C G K L 2m 4m A H 6 @ 5m= 30m
Cable AC exerts on beam AB a force P directed along line AC. Knowing that P must have a 350-lb vertical component, determine the magnitude of the force P * 550 A В 320 Ib 510 Ib 610 lb 430 lb None of the above
The two bars AC and CD are homogeneous and weigh 200 N/m. Joints A, C, and D are ball-and- sockets, and a cable is connected between B and E. Determine all forces that act on bar AC. 2 m 3 m E B 3 m D 4 m m
3. 240 N 240 N B The bracket BCD is hinged at C and attached to a control cable at B. For the loading shown, determine (a) the tension in the cable, (b) the reaction at C. a = 0,18 m OD -0.4 m- -0.4 m- 0.24 m
Situation 2. The rope CE exerts a 500-N force T on the hinged door. (a) Express T in terms of components; (b) determine the magnitude of the component of T´ perpendicular to the door. E (0.2, 0.4, –0.1) m y D T C (0, 0.2, 0) m A (0.5, 0, 0) m В (0.35, 0, 0.2) m
HW.: determine the forces in all cables B 30° 45° 200 N 500 N