Use the provided data wherever you need.(transmitted power 0.050 MW, speed 500 rpm, Modulus of Elasticity 220GPa, Modulus of Rigidity 70 GPa, Ultimate stress 620 MPa, Compressionstress = 240 MPa, Yield stress 440 MPa, Shear stress = 120 MPa, F.S. = 4,Bending moment = 0.5 KN m, diameter of rivet = 10 mm, pitch = 50 mm)).Q1. Design the key that is used to connect a shaft with a hub as shown in figure. 1.If the diameter of the shaft is 60 mm. Check the whole system.Figure 1

Answered: Image /qna-images/answer/e7565a4a-2d19-4f76-8280-f2024b8d398a.jpg

nsmitted power = 0.050 MW, speed 500 rpm, Modulus of Ela . , Modulus of Rigidity = 70 GPa, Ultimate stress = 620 MPa, s 240 MPa, Yield stress 440 MPa, Shear stress = 120 MI ding moment = 0.5 KN m, diameter of rivet = 10 mm, pitch = 50 %3! %3D Design the key that is used to connect a shaft with a hub as shown e diameter of the shaft is 60 mm. Check the whole system.

nsmitted power = 0.050 MW, speed 500 rpm, Modulus of Ela . , Modulus of Rigidity = 70 GPa, Ultimate stress = 620 MPa, s 240 MPa, Yield stress 440 MPa, Shear stress = 120 MI ding moment = 0.5 KN m, diameter of rivet = 10 mm, pitch = 50 %3! %3D Design the key that is used to connect a shaft with a hub as shown e diameter of the shaft is 60 mm. Check the whole system.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q4 Figure Q4 shows an aeroplane approaching a runaway for landing. The aeroplane consists of front and rear landing gear set which have different stiffness values. The front landing gear set has stiffness coefficient value, kı = 600 kN/m while the rear landing gear set has stiffness coefficient value, k2 = 700 kN/m. The distance of each landing gear to the center of gravity is l; = 9 m and I2= 2.5 m respectively. The mass of the aeroplane is given as m = 10,000 kg while the radius of gyration, rG= 2 m. By neglecting the damping coefficient of the landing gear: (a) Illustrate the problem as mass-spring system. (b) Construct the equation of motion, complete with all values in the matrix form.
A flanged bolt coupling consists of six 2-in. steel bolts evenly spaced around a bolt circle 12 in. in diameter, and four 3/4-in. aluminum bolts on a concentric bolt circle 8 in. in diameter. What torque can be applied without exceeding 6000 psi in the steel or 9000 psi in the aluminum? Assume Gst = 12 × 106 psi and Gal = 4 x 106 psi.
Problem 1: (P9, P10, M5, M7, D5) Obtain a preliminary design of the shaft by performing the following tasks. Note that forces T1=2880 N and T2-432 N. The maximum bending moment is at x =230 mm (point B), and it equals M= 698.3 N•m completely reversed, where the torque is constant at 612 N.m at the same point. The shaft material is AISI 1020 CD steel. Take the stress concentration conditions at B to be Shoulder fillet-sharp, with notch radius r=0.6 mm (Table 7-1). 230 mm 280 mm 30-mm dia. 300 mm 250-mm dia. 400-mm dia. 270 N X. 1800 N
Design a hallow shaft (Diameter and length) that develops 80 kN of power while rotating at a speed of 4000 rpm. The design constrains are as under: The angle of twist not to exceed 0.200 Shear stress is not to exceed 480 MN/m? The outer diameter is to be twice the inner diameter. The shaft length is to be three times the outer diameter. Modulus of rigidity = 79 GN/m?.
-100 Taper 1 in 100 /What is kind of shaft coupling illustrated in Figure (1), Draw tow views including one that show in figure where dimension of saddle key are (w=16, T-10mm) Figure (1)
A mini motorcycle is driven by a combustion engine with mechanical transmission. The 12Hp motor spins at a speed of 1150 rpm. The motorcycle runs at a linear speed of 45 km/h on 12-inch wheels. Preliminary center to center distance is 13”. This type of motorcycle requires two strands (conical double sleeve assembly) and is subjected to hard shocks. Can I get a detailed explanation for Choice of chain and sprocket. (Standard part number, see catalog) https://pdf.directindustry.com/pdf/martin-sprocket-gear/general-catalog/9091-246439.html
6.21-6.38 For the beam shown, derive the expressions for V and M, and draw the shear force and bending moment diagrams. Neglect the weight of the beam.
A steel shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of 50 MPa or twisting through more than 10 in a length of 26 diameters. Compute the proper diameter if G = 83 GPa. [Note: Attach your solution] %3D
A coupling GY8 is fixed on a shaft by a type C flat key, as shown in the figure. And the dimensions are also shown in the figure. The torque working on the shaft is 900N-m. [op]=100MPa. Please choose the dimension of the key and check its strength. op 27 = ×10³ kld 1. Note: Standard dimension series of flat key Diameter of shaft d >44-50 Width of key bx Height of key h 14x9 Length of key >75-85 >85-95 22x14 25×14 >50-58 >58-65 >65-75 16x10 18x11 20×12 6, 8, ..., 80, 90, 100, 125, 140, 160, 180, 200... Shaft 140 Coupling 70
The sbaft shown overhangs a bearing on the right and has the following dimensions: a - 5 in., b - 4 in., and - 10 in. The material is AISI C1040. annealed. This shaft is subjected to a torque T 10,000 in-lb., forces F - 10,000 lb. and F, 20,000 lb. Using a atatio-design approach, determine the diameter D for N 2.5, with eomputa- %3D Answer: a) Dia. = _inches %3D %3D %3D tions from the maximum shear stress theory. Note: Use Sy = 48,000 psi F2 N M
Design a square key for a 3 in diameter shaft to withstand a torque of 30000lb-in. The design stresses in shear and bearing can be safely taken as 11 ksi and 22 ksi, respectively. Find the length (inches) From Table AT 19, b=t=3/4 in
(8) An axle (non-rotating) is to be machined from AISI 1144, OQT 1,000°F, to the proportions keyway в shown, with a fillet radius r = 0.2D; F varies 1.SD from 400 lb. to 1,200 lb.; the supports are to the left of B, not shown. Let N = 2 (Soderberg Line). 6" (a) At the fillet, compute D and the 30 maximum tensile stress. (b) Compute D at section B. (c) Specify suitable dimensions. Keeping the given proportions, would a smaller diameter be permissible if the fillet were shot-peened?