Using method of joints. Thank you ProblemBoth of the boom DF of the jib crane and the column DE have a uniform weight of 50 lb/ft. The hoist and load weigh 30O Ib. Compute the following:1. At point A:A. internal normal force in the craneB. shear force in the craneC. bending moment in the crane2. At point B:A. internal normal force in the craneB. shear force in the craneC. bending moment in the crane3. At point C:A. internal normal force in the craneB. shear force in the craneC. bending moment in the crane4. 10 points for complete solution illustrations.•Bft--8 ft5 ft300 Ib7 ft

To find internal force at point A,B,C

Answered: oblem th of the boom DF of the jib…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

STRUCTURAL THEORY Show complete solution for better understanding Situation 1: From the truss shown, each member has a cross-sectional area of A = 400 mm 2, E = 200 GPa. Use the method of Virtual Work F b.-37.5 C.-30 d. 30 -2m- 1. Determine the stress on member AE a. 37.5 E c. 2 d.3 n B 45 KN 2 m 2. How many zero-force member are there? a. 0 b. 1 3. Determine the vertical deflection of joint E a. 1.42 b. 3.38 c. 2.95 d. 1.24 1.5 m
PROBLEM 1. A simple beam loaded as shown. Determine the following: (1) reactions @ support; & (2) Maximum Shear & Moment. Draw V & M diagram. P1-110 KΝ P2=229 KN B 1 m 3 m 2 m
1. The truck is moving along a 20 m span of beam. The front axle is 30 kN, the middle is 75 kN and the rear is 45 kN. The middle load is space 4m from the front and 8 m from the rear. a. Determine the moment under each axle. b. Calculate the maximum moment produced by the load. c. Calculate the maximum shear. 45 KN 75 KN 30 KN 8 m A 3 - 20 m 2 4 m B
A girder supports four concentrated loads of 800lb as shown in the figure. Assume the support at A is pin and B is a roller. Answer the following: A.) Compute the internal shear force, normal force and moment at a point 20ft from point A. Assign this point as point C.B.) Determine the shear and moment in the girder as a function of x, where 12ft < x < 24 ft.C.) Compute the maximum shear moment in the girder. (Draw the shear and moment diagram)
Thumbs-Up will be given. Write the complette solutions legibly. Answer in 3 decimal places Structural Theory a. Determine the vertical reaction R₂ in KN. b. Determine the shear at midspan between vertical supports in KN c. Determine the maximum factored load moment in the beam in KN.m
NEED IN 1HOUR PLS THANKS From the figure, compute for the horizontal and vertical component forces of the hinge at B acting upon member AC as shown.
Determine the horizontal and vertical reactions at supports A and D, and the tension in the rod/rope AD. Note: • Support A and E are hinge. • Support B is pin. • Support C and D are roller. • Member AD is a tension rod/rope. Required: • Horizontal and vertical reaction at A • Vertical reaction at D • Tension at rod/rope AD akym 4KN. Am 6m
Find the largest load P, that can be carried safely by the system below. Pin A is double shear. Given: Tall of pin A = 100 MPa %3D Sall on the rod BC = 20 MPa diameter of pin A, Øpin A = 10 mm diameter of the rod, Ørod = 20 mm C P -1 m -1 m -1 m 1 m B 0.75 m
The boom DF of the jib crane and the column DE have a uniform weight of 50 lb/ft. If the hoist and load weigh 300 lb, determine the internal normal force, shear force, and bending moment in the crane at points A, B, and C.
2 ft -2 ft 2 ft A 90 65 200 lb 100 lb 2. A beam AB is loaded as shown. The beam is pin-connected to the wall at A. At Ba 10-inch diameter pulley is attached through frictionless bearing to the beam. A rope passes around the pulley and is connected to C and D vertically above the extremities of the horizontal diameter of the pulley. Determine the pin reaction at A and the tension in the rope. Hint: Pin connection has vertical and hozirontal reactions.
7.3 The jib crane supports a load of F = 710 lb from the trolley which rides on the top of the jib. Determine the internal normal force, shear force, and moment in the jib at point C when the trolley is at the position shown. The crane members are pinned together at B, E and F and supported by a short link BH. Determine the internal normal force at point C. Determine the shear force at point C.
Find the force in member AB E 4m a. 4kN Tension b. 2kN tension 60⁰ c. 2kN compression d. 4kN Compression 2kN 60⁰ 2kN B 8m 30⁰ 2kN A

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS