power and average power absorbed by the passive linear network when the sinusoidal sources are given as v(t) = - 10 sin (30r) V and i(t) = 3 sin (30r + 100°) A. O Circuit in Figure Q4(a) is referred. By applying trigonometric identity, solve for the instantaneous 5 UTM 8 UTM 5 UTM 5 UTM UTM &UTM 8 UTM 8 UTM 5 UTM UTM & UTM/ Sinusoidal it) UTM &UTM s UTM source TM & UTM Passive linear 5 UTM 5 UTM S UT

power and average power absorbed by the passive linear network when the sinusoidal sources are given as v(t) = - 10 sin (30r) V and i(t) = 3 sin (30r + 100°) A. O Circuit in Figure Q4(a) is referred. By applying trigonometric identity, solve for the instantaneous 5 UTM 8 UTM 5 UTM 5 UTM UTM &UTM 8 UTM 8 UTM 5 UTM UTM & UTM/ Sinusoidal it) UTM &UTM s UTM source TM & UTM Passive linear 5 UTM 5 UTM S UT

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.27P: An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8...

See similar textbooks

Similar questions

An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
Q4/ Find the voltage average and the voltage waveform for the output of the circuit shown below. Vi=120v (rms) 2.1kr. V. to
A series RC circuit with R=4k ohms and C= 0.40 mF is connected to an AC voltage source e(t)= 100 sin200t. Determine the following: a). The overall power factor ( indicate big leading or lagging) b). The voltage drop across the resistor and the capacitor
Shown in the figure below is an "RL" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 9.84 Volts and is running at a frequency of f = 8.585e+04 Hz. The resistor has a resistance of R = 2170 and the inductor has an inductance of L = 3.54e-03 Henries. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Determine the numerical value of Ztot = 2890.5 Determine the numerical value of $z= = 41 Determine the current through the circuit: • I(PEAK) = 4.81E-3 • I(RMS) = 3.404E-3 Determine the voltage across the resistor: • VR(PEAK) = 7.387 • VR(RMS) = 5.22 ✔✔ Amps ✔Amps Write the FORMULA for the phase of the total impedance of the circuit z... = | tan-1 2701 R x Volts X Volts Determine the voltage across the inductor: • VL(PEAK) = 9.184 • VL(RMS) = 6.49 ✔ Volts Volts L R²+ WL- ✔ degrees 2 If a second circuit were connected in parallel with the inductor, this circuit would be considered as: O a low-pass filter O a capacitive switcher…
Q4/ Find the voltage average and the voltage waveform for the output of the circuit shown below. V=120v (rms) 2.1ke. V. ww
Q5)-a)For this figure shown below the phase relationship between the sinusoidal waveform Of this set. -10sin(wt+80) V=15sin (wt+40) Q5)-b) for this circuit find the max energy if XL=100 Vm-300v,L=0.3H V= Vm Sinwt
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
7 Find the average and effective values of voltage for sinusoidal waveform shown in Figure. Vm = 100 V 2x x14 9714 [Ans: 27.17 V, 47. 67 V]
Problem Design a circuit to limit a 20 V rms sinusoidal voltage to a maximum positive amplitude of 10 V and a maximum negative amplitude of -5 V using a single 14 V dc voltage source.
PHASE RELATIONSHIP SINUSOIDAL( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).
A DC-DC Chopper Circuit with an RL Load has an output current waveform shown below with a duty cycle of 50% and 1ms period. If it has a resistance of 1ohm and an inductance of 10mH, find the source voltage. 5A 2A ton toff output _current