Q.2. Air flows through a constant-area duct is connected to a reservoir at a temperature of 500°C and a pressure of 500 kPa by a converging nozzle, as shown in Figure. Heat is lost at the rate of 250 kJ /kg. Determine the exit pressure and Mach number and the mass flow rate fora back pressure of 0 kPa. q=250 kJ/kg Pr 500 kPa T,= 500°C Ph = 0 kPa D= 0.02m

Q.2. Air flows through a constant-area duct is connected to a reservoir at a temperature of 500°C and a pressure of 500 kPa by a converging nozzle, as shown in Figure. Heat is lost at the rate of 250 kJ /kg. Determine the exit pressure and Mach number and the mass flow rate fora back pressure of 0 kPa. q=250 kJ/kg Pr 500 kPa T,= 500°C Ph = 0 kPa D= 0.02m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An open tube is attached to a tank as shown. A). If Liquid X (Oil SG=0.55) rises to a height of 800 mm in the tube, what is the pressure Pa (in kPa) of the air above water? Neglect capillary effects in the tube. B). If Liquid X (Alcohol SG=0.79) rises to a height of 800 mm in the tube, what is the pressure Pb (in kPa) of the air above water? Neglect capillary effects in the tube.
(3) An open jet of water at 20 °C exits a nozzle into sea-level air and strikes a stagnation tube, as shown in the sketch. If the pressure at the centerline of section (1) is 11Okpa (abs), and losses are neglected, estimate: (a) the mass flow in kg/s, and (b) the height H of the fluid in the stagnation tube. (Atmospheric pressure =101.3 kpa) 4 cm Water 12 cm (1)- Sea-level air
5. Airat standard conditions enters the compressor shown below through a 2.4-in diameter pipe at 10 cfs. It leaves the tank through a 1.2-in diameter pipe at a velocity of 700 fps and has an increased density. Determine the average time rate of change of air density within the tank. 2.4 in 10 cfs 1.2 in 700 fps 0.00350 slugs/ft Tank Volume = 50 ft 0.00238 slugs/ft
Assuming oil has a unit weight of 60.53 lb/ft^3 and mercury with a SG = 13.55. Which statement is true? 4 in. Oil 3 in. 12 in. Water Mercury- The pressure in pipe A is greater than in pipe B. The pressure in pipe B is greater than in pipe A. The pressure in both pipes A and B are equal. O There is no pressure in both pipes.
An incompressible fluid flows through a horizontal pipe which tapers from a diameter of 2 cm to a diameter of l cm. The water enters the horizontal pipe at a velocity of 1 m/s. (Density is 1000 kg/m³) Compute: a) The velocity (m/s) at the exit of the pipe b) The mass flowrate (kg/s) at the exit of the pipe c) The pressure difference between section 1 and section 2: (P1-P2) D1=2 cm D2= 1 cm
Flow rate of a fluid (density = 1000 kg/m³) in a small diameter tube is 800 mm³/s. The length and the diameter of the tube are 2m and 0.5 mm, respectively. The pressure drop in 2m length is equal to 2.0 MPa. The viscosity of the fluid is
Air in a room at T0 = 290 K and P0 = 90 kPa is to be drawn by a vacuum pump through a 3-cm-diameter, 2-m-long adiabatic tube equipped with a converging nozzle at the inlet. The flow in the nozzle section can be approximated as isentropic. The static pressure is measured to be 87 kPa at the tube inlet and 55 kPa at the tube exit. Determine the mass flow rate of air through the duct, the air velocity at the duct exit, and the average friction factor for the duct.
Problem 7-72 What is the Air at 1500 kPa absolute flows in a 25-mm-diameter tube. maximum laminar flow rate. Use density of air = 14.04 kg/m³ and μ = 0.0000217 Pa-s. Ans: 0.061 L/s
Flow rate of a fluid (density = 1000kg/ m³) in a small diameter tube is 800 m³/ s. The length and the diameter of the tube are 2m and 0.5mm respectively. The pressure drop in 2m length is equal to 2.0 MPa. The viscosity of the fluid is
Glycerin (sg = 1.26) t 40°C flows in the portion of the duct outside the square tubes as shown in the figure. Calculate the Reynolds number for the flow rate of 0.10 m3/s and dynamic viscosity is 0.30 Pa-s.
A pressure gage at elevation of 12m at the side of the tank containing liquid reads 100 kPa. Another gage at elevation 7 m reads 140 kPa. Compute the density of the liquid. L00 kPa - El. 12 Sm 140 kPa - El. 7
a) When oil (p=850 kg/m³) flows through a 5 cm diameter horizontal pipe of 12 m length at a velocity of 1.2 m/s a pressure difference of 5000 N/m² is recorded. i) Assuming laminar flow calculate the viscosity of the liquid. ii) Check that the assumption of laminar flow is valid b) Air (p=1.287 kg/m³) flows into a jet engine of diameter 1.2 m as shown in Figure Q4b at a velocity of 90 m/s. Upon landing, the engine exhaust exits through the reverse thrust mechanism with a speed of 275 m/s symmetrically in the directions indicated. Assume that the inlet and outlet pressures are atmospheric and that the mass flow rate of fuel is negligible compared to the air flow rate through the engine. i) Determine the x and y velocity components of the exhaust leaving the engine ii) Evaluate the horizontal and vertical forces experienced by the engine C3=275 m/s (3) C1=90 m/s 1.2 m diameter (1) 30 degree (2) C2=275 m/s Figure Q4b