Q3) A 5 cm diameter steel pipe is covered with a 1cm layer of insulating material having k 0,22 W/m -C followed by a 3 cm thick layer of another insulating material having k-0.06 W/m C The entire assembly is exposed to a convection surrounding condition of h-60 W/m² C and Too -15 °C. The outside surface temperature of the steel pipe is 400'C. Calculate the heat lost by the pipe-insulation assembly for a pipe length of 20 m. Express in Watts.

Q3) A 5 cm diameter steel pipe is covered with a 1cm layer of insulating material having k 0,22 W/m -C followed by a 3 cm thick layer of another insulating material having k-0.06 W/m C The entire assembly is exposed to a convection surrounding condition of h-60 W/m² C and Too -15 °C. The outside surface temperature of the steel pipe is 400'C. Calculate the heat lost by the pipe-insulation assembly for a pipe length of 20 m. Express in Watts.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.43P: 2.43 A turbine blade 6.3 cm long, with cross-sectional area and perimeter , is made of stainless...

See similar textbooks

Similar questions

3.17 A 1.4-kg aluminum household iron has a 500-W heating element. The surface area is . The ambient temperature is 21°C, and the surface heat transfer coefficient is . How long after the iron is plugged in does its temperature reach 104°C?
1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
An electronic device that internally generates 600 mW of heat has a maximum permissible operating temperature of 70C. It is to be cooled in 25C air by attaching aluminum fins with a total surface area of 12cm2. The convection heat transfer coefficient between the fins and the air is 20W/m2K. Estimate the operating temperature when the fins are attached in such a way that (a) there is a contact resistance of approximately 50 K/W between the surface of the device and the fin array and (b) there is no contact resistance (in this case, the construction of the device is more expensive). Comment on the design options.
2.9 In a large chemical factory, hot gases at 2273 K are cooled by a liquid at 373 K with gas-side and liquid-side convection heat transfer coefficients of 50 and , respectively. The wall that separates the gas and liquid streams is composed of a 2-cm thick oxide layer on the gas side and a 4-cm thick slab of stainless steel on the liquid side. There is a contact resistance between the oxide layer and the steel of . Determine the rate of heat loss from hot gases through the composite wall to the liquid.
The interior wall of a large, commercial walk-in type meat freezer is covered under normal operating conditions with a 2-cm thick layer of ice. One day, a power outage cuts electricity to the refrigeration system of the freezer. Estimate the time required to melt this layer of ice if it has a mass density of 700kg/m3 and a latent heat of fusion of 334 kJ/kg. Consider the air temperature inside the freezer to be 20C with a heat transfer coefficient of 2W/m2K for convection from the freezer surface to air, and clearly state the assumptions made in your calculations.
One end of a 0.3-m-long steel rod is connected to a wall at 204C. The other end is connected to a wall that is maintained at 93C. Air is blown across the rod so that a heat transfer coefficient of 17W/m2 K is maintained over the entire surface. If the diameter of the rod is 5 cm and the temperature of the air is 38C, what is the net rate of heat loss to the air?
A cooling system is to be designed for a food storage warehouse for keeping perishable foods cool prior to transportation to grocery stores. The warehouse has an effective surface area of 1860 m2 exposed to an ambient air temperature of 32C. The warehouse wall insulation (k=0.17W/(mK)) is 7.5 cm thick. Determine the rate at which heat must be removed (W) from the warehouse to maintain the food at 4C.
1.49 A small oven with a surface area of is located in a room in which the walls and the air are at a temperature of . The exterior surface of the oven is at , and the next heat transfer by radiation between the oven’s surface and the surroundings is 586 W. If the average convection heat transfer coefficient between the oven and the surrounding air is 11 calculate (a) the net heat transfer between the oven and the surroundings in W, (b) the thermal resistance at the surface for radiation and convection, respectively, in K/W, and (c) the combined heat transfer coefficient in .
2.43 A turbine blade 6.3 cm long, with cross-sectional area and perimeter , is made of stainless steel . The temperature of the root, , is . The blade is exposed to a hot gas at , and the heat transfer coefficient is K. Determine the temperature of the blade tip and the rate of heat flow at the root of the blade. Assume that the tip is insulated.
2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
1.67 In beauty salons and in homes, a ubiquitous device is the hairdryer. The front end of a typical hairdryer is idealized as a thin-walled cylindrical duct with a 6-cm diameter with a fan at the inlet that blows air over an electric heating coil as schematically shown in the figure. The design of this appliance requires two power settings, with which the air blown over the electric heating coil is heated from the ambient temperature of to an outlet temperature of and with exit air velocities of 1.0 m/s and 1.5 m/s. Estimate the electric power required for the heating coil to meet these conditions, assuming that heat loss from the outside of the dryer duct is neglected.
1.52 A flat roof of a house absorbs a solar radiation flux of . The backside of the roof is well insulated, while the outside loses heat by radiation and convection to ambient air at . If the emittance of the roof is 0.80 and the convection heat transfer coefficient between the roof and the air is K, calculate (a) the equilibrium surface temperature of the roof and (b) the ratio of convection to radiation heat loss. Can one or the other of these be neglected? Explain your answer.