Q7: What is the compression in the tibia of lengthh = 30 cm of a person of mass m =standing erect? The bone is regarded as a hollow circular tube with internal radius r, = 1.2 cmand external radius r, = 1.75 cm, and Young's modulus along the axis is Y = 2 × 1010N/m².If the maximum tensile strength of tibia is 1.4 × 10®N/m², What is the compression in the tibiaat the point of fracture?80 kg%3DFibula1.Tibia

Data given h= L = 30 cm = 0.3m m = 80 kg r1 = 1.2 cm = 0.012 m r2 = 1.75 cm = 0.0175 m E = 2×…

Q7: What is the compression in the tibia of length h standing erect? The bone is regarded as a hollow circular tube with internal radius r = 1.2 cm and external radius r2 = 1.75 cm, and Young's modulus along the axis is Y = 2 x 1010N/m². If the maximum tensile strength of tibia is 1.4 x 10°N/m2, What is the compression in the tibia at the point of fracture? 30 cm of a person of mass m = 80 kg %3D

Q7: What is the compression in the tibia of length h standing erect? The bone is regarded as a hollow circular tube with internal radius r = 1.2 cm and external radius r2 = 1.75 cm, and Young's modulus along the axis is Y = 2 x 1010N/m². If the maximum tensile strength of tibia is 1.4 x 10°N/m2, What is the compression in the tibia at the point of fracture? 30 cm of a person of mass m = 80 kg %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2/ In the nucleus pulposus of an intervertebral disc, the compressive load is 1.5 times the externally applied load. In the annulus fibrosus, the compressive force is 0.5 times the external load. What are the compressive loads on the nucleus pulposus and annulus fibrosus of the L5-S1 intervertebral disc of a 90 kg man holding a 50 kg weight bar across his shoulders, given that 63% of body weight is distributed below the disc?
9.2 (A). Determine the change in volume of a thin cylinder of original volume 65.5 x 10-'m' and length 1.3 m if its wall thickness is 6 mm and the internal pressure 14 bar (1.4 MN/m?). For the cylinder material E- 210GN/m2; v= 0.3. [17.5 x 10-m')
solve the following for forces and displacement at each of the nodes. where F is 500lb. M is 70 ft.lb; W is 8000 Ib/ft W lb/ft 15 ft 10 ft E= 30 x 10 psi A=5 in.? 1= 200 in. 45° F
Find the force pneed to fill the gap. Young's modulus as 300 GPa C 1,5 cm² 2 cm2 P. A 1 cm 1/2 p 0.5 m 0.5 m 1 m 0.5 mm (a) 13.84KN. (b) 14.21KN.
Determine the axial force (kN) in each member of the assembly shown below. Member Cross-Sectional Area Modulus of Elasticity AB 1,400 mm2 200 GPa BC 1,800 mm2 200 GPa DB 1,400 mm2 200 GPa BY 18KN A 400mm 400mm 400mm 55.00° 55.00°
A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loding if three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in z direction. If v=0.30 and E=29x10^6 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading. DetermineNormal strain in x, y & z direction.Elongation in x, y & z direction.
An elevator weighs 1000 lbs and is supported by a 5/16 inch diameter cable, 1500 ft long. When the elevator carries a passenger load of 1000 lbs, the cable elongates 6/7 inches more. What is the modulus elasticity of the cable? A 4.56 x108 Ib/in? B 5.48 x108 Ib/in? 5.48 x106 Ib/in? D 4.56 x106 Ib/in²
A normal-weight concrete masonry unit is 40cm by 20cm by 15cm thk. A wall made up of this material, fully grouted and plastered, is supported by a beam. The wall dimension is (H x L) 3m by 5m. The plaster thickness on both wall faces is 15mm. The density of the unit is 21.2 kN/m³, while the density of the grout is 22 kN/m³. Determine the conservative superimposed dead load on the beam in kN/m. Use two decimal places.
A copper wire has a radius of 3.5 mm. When forces of a certain equal magnitude but opposite directions are applied to the ends of the wire, the wire stretches by 5.0×10^-3 of its original length. Young's modulus for copper is 11×10^10 Pa What is the magnitude of the force on either end?
CDEFGH is plate with a circular hole in it and has a unit weight p = 2 kN/m². If the initial length of the spring is 1m, find the stretched length of the spring attached at C to the given system. The stiffness of the spring id k-50 kN/m. p H 0 2 m Lütfen birini seçin: D A. 1.6019 m B. 1.8258 m C. 2.0480 m D. 2.2694 m E. 1.3727 m F. None of the above X 2 m 2 m G 2 m F E 3m 1m
A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as follows: 48 kips tension in the x direction, 60 kips compression in the y direction, and 54 kips tension in the z direction. If the Poisson’ Ration is 0.30 and the modulus of elasticity is 29xksi, determine the deformations at each direction. Also, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.
A rectangular steel block is 3 inches long in the x direction, 2 inches long in the y direction, and 4 inches long in the z direction. The block is subjected to a triaxial loading of three uniformly distributed forces as floows; 48 kips tension in the x directio, 60 kips compression in the y direction, and 54 kips tension in the z direction. If v = 0.30 and E = 29 x 106 psi, determine the single uniformly distributed load in the x direction that would produce the same deformation in the y direction as the original loading.