Ql-mm ,length 40 mm. The final diameter 18 mm and length 45 mm.Draw the force-extension diagram and determine the following :a) Ultimate tensile strength,c) Modulus of elasticity, d) Percent elongation and e) Percent reduction in area.The following data collected from tensile test of a metal bar diameter 20b) The fracture strength,Force - kN7590 | 10512013112511025504.7Extension-mm0.02 0.040.060.20 - 0.601.603.004.0Fracture

Given-Data:- Diameter(D)=20 mm Length(L)=40 mm Final Diameter(D)=18 mm Final Length (L)=45mm…

Ql- i mm ,length 40 mm. The final diameter 18 mm and length 45 mm. Draw the force-extension diagram and determine the following : a) Ultimate tensile strength, c) Modulus of elasticity, The following data collected from tensile test of a metal bar diameter 20 b) The fracture strength, d) Percent elongation and e) Percent reduction in area. Force - kN 25 50 120 131 125 110 75 90 105 4.7 Extension-mm 0.02 0.04 0.06 0.20 |- 0.60 | 1.60 3.00 4.0 Fracture

Ql- i mm ,length 40 mm. The final diameter 18 mm and length 45 mm. Draw the force-extension diagram and determine the following : a) Ultimate tensile strength, c) Modulus of elasticity, The following data collected from tensile test of a metal bar diameter 20 b) The fracture strength, d) Percent elongation and e) Percent reduction in area. Force - kN 25 50 120 131 125 110 75 90 105 4.7 Extension-mm 0.02 0.04 0.06 0.20 |- 0.60 | 1.60 3.00 4.0 Fracture

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Based upon the information in the table below, which material is the stiffest? Elastic Strain at Fracture Fracture Yield Strength (MPa) Tensile Modulus Strength (MPa) 120 550 340 Fractures before yielding 850 Strength (MPa) 105 500 265 650 720 Material 100 415 310 0.40 0.15 0.23 (GPa) 150 310 210 350 210 700 0.14 OE OB A. OD
Q2c) Listed in the table below is the tensile stress-strain data for different grades of steels. Utilizing the data given answer the three queries given below. Tensile Strain at Fracture Strength Strength Fracture Strength Modulus Material Yield Elastic (MPa) (MPa) (MPa) (GPa) А 410 1440 0.63 265 410 200 220 0.40 105 250 C 815 950 0.25 500 610 800 650 0.14 720 210 E Fractures before yielding 650 550 1) Which will experience the greatest percent reduction in area? Why? 2) Which is the strongest? Why? 3) Which is the stiffest? Why? B.
The following engineering tensile properties are given for the 1080 steel:-Yield strength (MPa): 585-Tensile strength (MPa): 965-Elongation to fracture for specimen of 5cm gage length (%): 12A 5cm long circular rod of 1080 steel specimen with a diameter of 1.28cm isloaded to failure in tension. a) What was the maximum load needed to break the specimen?(20 points)b) If necking initiated at 80% of the total elongation, prior to this point thespecimen deformation is uniform, compute the true stress at the point ofnecking initiation.
ASAP
A bronze alloy specimen having a diameter of 12.8 mm and a gage length of 50 mm was tested to fracture. Stress and strain data obtained during the test are shown in Figure. Determine: 400 - Upper scale a. the modulus of elasticity. 320 b. the proportional limit. Lower scale c. the ultimate strength. 240 d. the yield strength (0.20% offset). 160 e. the modulus of resilience. f. the true fracture stress if the 80 final diameter of the specimen at the location of 0.100 0.005 0.300 0.015 0.200 0.400 the fracture was 10.5 mm. 0.010 0.020 g. The Poisson's ratio. Strain (mm/mm) Stress (MPa)
A tensile test specimen of 1045 hot-rolled steel having a diameter of 0.505 in. and a gage length of 2.00 in. was tested to fracture. Stress and strain data obtained during the test are shown. Determine the ultimate strength. Stress (ksi) 60 50- 40- 30- 20 10- 0 0 0 Upper scale O 66 ksi 28 ksi O 72 ksi O 53 ksi O 62 ksi Lower scale. 0.025 0.050 0.075 0.100 0.125 0.150 0.175 0.002 0.004 0.006 0.008 0.010 0.012 0.014 Strain (in./in.)
The table below shows the deformation data that resulted from applying a pure tensile load to a brass alloy rod with an initial length of 30 mm and a diameter of 10 mm. This rod was subjected to necking and beyond necking deformation. The data at fracture is shown in the last row. Applied Load (N) Length (mm) Diameter (mm) 75,100 33.8 68, 250 34.9 50,200 35.7 6.7 Solve for the TRUE STRESS/ES and TRUE STRAINS. 8.3 7.8
Stress Strain Diagram The Data shown in the table have been obtained from a tensile test conducted on a high-strength steel. The test specimen had a diameter of 0.505 inch and a gage length of 2.00 inch. Using software. plot the Stress-Strain Diagram for this steel and determine its: A= TTdT(050s A %3D 1. Proportional Limit, 2. Modulus of Elasticity, 3. Yield Strength (SY) at 0.2% Offset, 4. Ultimate Strength (Su), 5. Percent Elongation in 2.00 inch, 6. Percent Reduction in Area, 7. Present the results (for Steps 1-6) in a highly organized table. e Altac ie sheet (as problelle 4 A = 0.2.002 BEOINNING of the effort Elongation (in) Elongation (In) Load Load #: #3 (Ib) (Ib) 1 0.0170 15 12,300 0.0004 1,500 16 12,200 0.0200 0.0010 3. 3,100 17 12,000 0.0275 0.0016 4,700 18 13,000 0.0335 5. 6,300 0.0022 19 15,000 0.0400 0.0026 6. 8,000 20 16,200 0.055 0.0032 9,500 21 17,500 0.0680 0.0035 8. 11,000 22 18,800 0.1080 0.0041 11,800 23 19,600 0.1515 0.0051 24 20,100 0.2010 10 12,300 0.0071 25…
A tensile test for a copper specimen has been performed and the following data are obtained. - Percentage of Elongation = 66 % - Percentage of Reduction in Area = 38 % - Final length after fracture = 34.6 mm - Final Diameter after fracture = 4.43 mm & - Ultimate stress = 364 MPa Determine the Initial length, Initial diameter and Maximum load. i) Initial Length (in mm) = ii) Final Area (in mm2) = iii) Initial Area (in mm2) = iv) Initial Diameter (in mm) = v) Ultimate Load (in N) =
A tensile test specimen of stainless steel alloy having a diameter of 0.495 in. and a gage length of 2.00 in. was tested to fracture. Stress and strain data obtained during the test are shown. Determine the true fracture stress if the final diameter of the specimen at the location of the fracture was 0.350 in. Stress (ksi) 120 Upper scale Lower scale H 0.0 0.020 0.040 0.060 0.080 0.100 0.120 0.0 0.002 0.004 0.006 0.008 0.010 0.012 Strain (in./in.) 90 60 30 0- 300 ksi O 126 ksi EA O 237 ksi O 202 ksi O 261 ksi
The following data was obtained as a result of tensile testing of a standard 0.505 inch diameter test specimen of magnesium. After fracture, the gage length is 2.245 inch and the diameter is 0.466 inch. a). Calculate the engineering stress and strain values to fill in the blank boxes and plot the data. Load(lb) Gage Length (in) Stress (kpsi) Strain 0 2 1000 2.00154 2000 2.00308 3000 2.00462 4000 2.00615 5000 2.00769 5500 2.014 6000 2.05 6200 (max) 2.13 6000 (fracture) 2.255 b). Calculate the modulus of elasticity c). If another identical sample of the same material is pulled only to 6000 pounds and is unloaded from there, determine the gage length of the sample after unloading.
A tensile test for a copper specimen has been performed and the following data are obtained. - Percentage of Elongation = 66 % - Percentage of Reduction in Area = 38 % - Final length after fracture = 34.6 mm - Final Diameter after fracture = 4.43 mm & - Ultimate stress = 364 MPa Determine the Initial length, Initial diameter and Maximum load. ii) Final Area (in mm2) = iii) Initial Area (in mm2) =