Question-2 Consider the following circuit (assuming the ideal diode model): iD 21/ +1 DiciLV ic↓ (a) Given that: vs = 100 cos(2n50t) V, R = 10k , C = 200μF R PI-1c]: a) Calculate the maximum current through the load, IL b) Calculate the voltage ripple value, Vr c) Calculate the conduction angle, wit 10 10

Question-2 Consider the following circuit (assuming the ideal diode model): iD 21/ +1 DiciLV ic↓ (a) Given that: vs = 100 cos(2n50t) V, R = 10k , C = 200μF R PI-1c]: a) Calculate the maximum current through the load, IL b) Calculate the voltage ripple value, Vr c) Calculate the conduction angle, wit 10 10

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is CEMF?
4670V = VsR = 200kΩ C = 0.1μF Consider the circuit and parameters illustrated above. If a derating factor of 12% is sugested then calculate, 12) the maximum reverse voltage rating of the diodes; 13) the string efficiency of this arrangement; 14) the maximum difference in leakage current of the diodes; 15) the maximum difference in stored charge of the diodes.
The diode current in a p-n junction is modeled exponentially (given below.) When the p-n junction is polarized with 0.7V and 0.75V, the currents flowing through the diode are again measured on the basis of 1.36 mA and 7.20 mA. Accordingly, what is the ideality factor? (Note: Take the thermal voltage as mV)
In the given system; Va, Vb, Vc effective value is 220V, Ly=300 mH and Ry=22 Ohms.It was observed that the yuk current is continuous when the tristorier is triggered for alpha=65 degrees; and D1the average value of the diode current was calculated as ID1 avg = 1.703A.Accordingly, calculate the average value of the current flowing through T3. IT3_ avg=?
(a) Calculate the current at t = 0+ in the circuit shown. (b) Calculate IF, IR, and the storage time expected when the diode is switched off if τT = 8 ns.
Calculate diode forward current IF, diode voltage VF, and voltage drop across series resistor for three diode models (ideal, practical and complex).Assume diode forward resistance (dynamic resistance) r’d = 25Ω. Reverse leakage current IR = 75 nanoA with series resistance of RL = 100kΩ in reverse bias. Draw equivalent circuit diagrams of each model separately and plot corresponding I/V characteristics for each model.
Find the value of dc and ac resistance of a Germanium junction diode if the temperature is 25 degree Celcius, Reverse Saturation Current is 20 microAmperes and applied voltage of 0.1V. a.) rDC= 75.6 ohms, rAC=11.2 ohms b.) rDC= 120.7 ohms, rAC= 28.4 ohms c.) rDC= 95.1 ohms, rAC=12.3 ohms d.) rDC= 109.2 ohms, rAC=26.3 ohms
DiodesFill in the blanks with the words belowcheck valve, conductance, convert, crystalline, impurities, infinite, galena, p–n junction, rectifying,resistance, selenium, semiconductor, switching circuits, tailored, temperature, threshold, two-terminal,unidirectionalA diode is a 1 ………………… electronic component that conducts current primarily in one direction(asymmetric 2 ………………..); it has low (ideally zero) 3 ……………… in one direction, and high (ideally4 ………………..) resistance in the other. A 5 ………….. diode, the most common type today, is a 6……….. piece of semiconductor material with a 7 ………………. connected to two electrical terminals. Avacuum tube diode has two electrodes, a plate (anode) and a heated cathode. Semiconductor diodes were thefirst semiconductor electronic devices. The discovery of crystals' 8 ……………… abilities was made byGerman physicist Ferdinand Braun in 1874. The first semiconductor diodes, developed around 1906, weremade of mineral crystals such as 9 ……………….. . Today,…
Q: A single-phase, full-wave diode bridge is used to supply power to aresistive load of value R = 75 Ω. If the supply voltage is sinusoidal,Vs = 400 sin ωt, Calculate: 1) the average and rms values of the load current. (IL rms), (Idc) 2)the ripple factor (RF)for the load current wave operation.
Apply each of diode approximations given the following parameters D`:rB= 2 ohms, rR= 220 kilohms: Si, rB = 5 ohms, rR= 560 kilo ohms Determine the current flowing through D1, D2 AND R2, R3, THE VOLTAGE ACROSS R3 SOLVE IN THREE DIODE APRROXIMATIONS
1. Briefly discuss the difference between Piecewise-linear model, Simplified model, and Ideal device. 2. Discuss briefly how to test junction diode. 3. Study the diode specification sheets of a 1N4001 and 1N5401 diodes provided by the manufacturer and compare their difference. Give typical application of each.
Calculate diode forward current IF, diode voltage VF, and voltage drop across series resistor for three diode models (ideal, practical and complex). Assume diode forward resistance (dynamic resistance) r’d = 25Ω. Reverse leakage current IR = 75A with series resistance of RL = 100kΩ in reverse bias. Draw equivalent circuit diagrams of each model separately and plot corresponding I/V characteristics for each model.