Question #4 v(t) Ra Rb Ve(t) In the above circuit, the initial conditions are all zero and the op-amp is ideal. A. Determine the transfer function, H(s) = v() in one of the following forms: i) H(s) = kwhere k, b and c are constants; ii) H(s)k- where k, b and c are constants; iii) H(s) k ba ba where k, b and c are constants; B. iv) H(s) k ,where k, b and c are constants. Determine the type of filter implemented by the circuit C. If the circuit is a low-pass or high-pass filter, do Parts i and ii. If the circuit is a band- pass or band-reject filter, do Parts iii. i) Determine the order of the filter. ii) Find the values for the relevant components that will yield a gain of 8 under the requirement that ALL resistors must have a resistance greater than or equal to 1kn iii) Find the values for the relevant components that will yield a bandwidth of 8 = 12500 rad/s and a gain of 8 at the resonance frequency under the requirement that ALL resistors must have a resistance greater than or equal to 1kn. Solution #4 A. H(s) k ba where k = -B b = c B. с C = CARD Bandpass Filter R₂ = 1 kn, R₁ 16 kn, C=10nF

Question #4 v(t) Ra Rb Ve(t) In the above circuit, the initial conditions are all zero and the op-amp is ideal. A. Determine the transfer function, H(s) = v() in one of the following forms: i) H(s) = kwhere k, b and c are constants; ii) H(s)k- where k, b and c are constants; iii) H(s) k ba ba where k, b and c are constants; B. iv) H(s) k ,where k, b and c are constants. Determine the type of filter implemented by the circuit C. If the circuit is a low-pass or high-pass filter, do Parts i and ii. If the circuit is a band- pass or band-reject filter, do Parts iii. i) Determine the order of the filter. ii) Find the values for the relevant components that will yield a gain of 8 under the requirement that ALL resistors must have a resistance greater than or equal to 1kn iii) Find the values for the relevant components that will yield a bandwidth of 8 = 12500 rad/s and a gain of 8 at the resonance frequency under the requirement that ALL resistors must have a resistance greater than or equal to 1kn. Solution #4 A. H(s) k ba where k = -B b = c B. с C = CARD Bandpass Filter R₂ = 1 kn, R₁ 16 kn, C=10nF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

For the circuit above, R= 4MΩ and C = 0.75μF. Vi(t)= −t^2V for 0s≤t≤5s. What is the value of Vo at time t=5s, if Vo(0) = 0? You can assume the operational amplifier behaves as an ideal op amp with power supplies of +15 and -15. Give your answer in volts.
You are given the following circuit. Assume that V1 = 6.2 V, V2 = 5.6 V, V3 = 7.1 V, V4 = 4.9 V, V5 = 7.6 V, R1 = 18 kΩ, R2 = 33 kΩ, R3 = 74 kΩ, R4 = 50 kΩ, and R5 = 29 kΩ. What is the voltage vn at the inverting terminal of the op-amp?( need only handwritten solution .otherwise downvote.)
The op amp circuit shown is ideal. The values for the circuit are as follows:+VCC = 12.0V, -VCC = -10.0V, Ra = 9.00Ω, Rb = 30.0Ω, Rc = 42.0Ω, Rd = 4.00Ω, Re = 32.0Ω. Write a KCL equation at node n. Solve for the output voltage vout as a function of the inputs va and vb. If input va=2.00V and output vout =10.0V, then solve for input vb. If inputs va=8.00V and vb=5.00V, then solve for the power absorbed by Rb. If input va=4.00V, then solve for the range of input vb such that the amplifier does not saturate.
Use the Thevenin and/or Norton theorems to determine the output voltage, V0,and the gain, G, of the op amp circuit. Please show all work and explain the steps a bit:)
Sketch the root locus of the system whose open loop transfer function is G(s)=k/s(s+4)(s+6). Find the value of k so that damping ratio of closed loop system is 0.6.
The op amp circuit of the figure shown below will remove the DC portion of the input voltage, v1(t), while amplifying the AC portion. Let v1(t) = 9 + 10-3 sin 600t V, RF= 36 kΩ, and Vbatt = 12 V. Find RS(in kΩ) such that no DC voltage appears at the output. (Enter your answer as a number without the units.)
Electrical Engineering For a unit feedback system having the following gain functions: G(s) Ks - 4.21) s² (2 s +5.7) 2 (1) Draw the root trajectory. (2) Find the value of the gain K in which all three roots are real and have intermediate roots. (3) When it becomes as in (2), find the value of its root. -thanks you very much for the help ~~
Design a combinational circuit with three inputs (E,L,Y) and three outputs (F,R,A). If the input is less than 5, then the output is 2 greater than the input. Otherwise, the output is 3 less than the input. if E=0 L=0 and Y=0, then if E=0 L=0 and Y=1, then if E=0 L=1 and Y=0, then if E=0 L=1 and Y=1, then…
Is it possible to get a gain less than unity using a non-inverting amplifier configuration? If yes, sketch a circuit.''please solve it in computer font, not on paper''
Explain the following systems (figure and transfer function): a) open loop systemsb) closed-loop systems
4.37 Find the range of Rf for which the op amp in the circuit of Fig. P4.37 does not saturate
The loop gain GH of a closed loop system is given by the following expression K/s(s+2)(s+4), The value of K for which the system just become unstable is ?