Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 9 mm in diameter. Assume a = 600 mm, b = 300 mm, h = 400 mm, P = 875 N, and 0 = 55°. Determine the following: (a) the normal stress in rod (1) (b) the shear stress in pin B (c) the shear stress in pin A D Answers: (a) Orod= (b) Tpin B = (c) Tpin A = (1) a i H i B b MPa MPa MPa

Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 9 mm in diameter. Assume a = 600 mm, b = 300 mm, h = 400 mm, P = 875 N, and 0 = 55°. Determine the following: (a) the normal stress in rod (1) (b) the shear stress in pin B (c) the shear stress in pin A D Answers: (a) Orod= (b) Tpin B = (c) Tpin A = (1) a i H i B b MPa MPa MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Q.I: A shaft composed of segments AB, BC is fixed between the two walls at A and C and loaded as…

Q: Figure In the figure shown, a bar ABC with negligible mass carries a 20 kN load and is supported by…

A: the allowable shear stress of the pin in not given to get the diameter of the pin.please put the…

Q: A uniform cross-section bar is shown in the figure. This bar is set on the wall and subjected to a…

A: For solution refer below images.

Q: The assembly shown in the figure below consists of two sections of galvanized steel pipe connected…

Q: 1. A uniform crane arm (length L) is attached to the rest of the crane by a frictionless axle at its…

Q: he davit shown in the figure is supported by a cable at B and pinned at A and is subjected to a…

A: To Find : The normal stress in the tie rod (1) The shearing stress in the pin at A The shearing…

Q: The solid shaft shown in the figure below is fixed at one end and has a lever at the other. The…

A: Given data, Applied force, F = 840 N Distance, b = 110 mm Shear stress induced at point A on the…

Q: The end plates of a high pressure boiler accumulator are fixed using a number of bolts of M 16 cross…

A: Any action that can change the state of motion is called force. Force is described by its magnitude,…

Q: What is the maximum permitted tension in N in the cable if the vertical deflection at A has a design…

A: calculate the allowable twist: deflection at point A = 15 mm L1 = 200 mm twist = allowed delection/…

Q: Two steel tubes are joined at B by four pins (d p =11mm), as shown in the cross section a–a in the…

A: Given: d p =11mm tAB = 6.5 mm tBC = 7.5 mm In tension σY = 200 MPa σU =340 MPa To determine: the…

Q: The beam is supported by a pin at B and a roller at D. The applied loads shown in the figure have…

A: here, F1=790 lbF2=610 lbw= 140 lb/fta=6 ftb=13.8 ftc= 4.8 ft

Q: Which of the folloving equations correctiy describe the bending moment M and torsion Tin section BC…

Q: Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1)…

Q: Three solid cylindrical rods are welded together to form the compound axial member shown in the…

Q: A prismatic wing box is constructed of two cylindrical tubes (each of thickness welded to top and…

Q: PROBLEMS Figure 1. In the figure shown, a bar ABC with negligible mass carries a 20 kN load and is…

A: Draw FBD

Q: Problem 4. The 16 × 22 × 100-mm rubber blocks (E = 54.76 MPa and v = 0.48) shown in the figure are…

A: Given: Length of the rubber block→L=100 mm Height of the rubber block→H=22 mm Allowable shear…

Q: Q3 A portable conveyor is to be raised and lowered using the double power screw arrangement as shown…

A: Given:Value of the total load, Design stress of the power screw, Lead angle of the screw,…

Q: Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1)…

Q: 0.5 m B P 3P -1.5 m2 m 6P 1.5 m- P 0.5 m A For the figure at left: P = 10 KN ● ● ● Bar BC cross…

A: Given: The load, P = 10 kN, The diameter of each pin, d = 18 mm, The cross-section fo BC, ABC = 25…

Q: A rigid bar, pinned at O, is supported by two identical springs as shown in the figure. Each spring…

A: The maximum allowed load can be determined from the shear stress condition as shown below.

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5…

Q: A rigid body ABCKDE is in equilibrium under the e?ect of a set of loads as shown in the Figure. The…

A: Given data, Maximum intensity of distributed load, w = 15 kN/m Applied concentrated force, F1 = 30…

Q: A solid steel bar of diameter d, = 45s.0 mm is enclosed by a steel tube of outer diameter d, = 52.5…

Q: This is a multi-part question. Once an answer is submitted, L- P

A: Given-Information:- Length, L = 4 m Angle size 100×100×12 mmP =3000 N a =1.75 m =1750 mmW =1000 N/m…

Q: Which of the following general equations can be used to find the vertical deflection of A in the y…

Q: The rigid element ABCD is supported by a pin at C and two rods at A and D as shown in the figure. A…

A: Draw the free-body diagram of ABCD. Apply moment equilibrium about point C.…

Q: C Rod 45° 7' Steel Plate A 12' P.

A: FBD of the given system is mentioned above Volume of steel plate= 12×7×1= 84 inch3= 0.0486111 ft3…

Q: An idealized model of a thin-walled convertible car body cross-section is shown in figure Q16. The…

Q: A 3 m long steel angle shown in the figure has a section thickness of 12.7 mm and a cross sectional…

Q: A pickup truck tailgate supports a crate (Wc = 420 lb), as shown in the figure. The tailgate weighs…

A: The given information in the problem is shown in the following attached image:

Q: The rigid element ABCD is supported by a pin at C and two rods at A and D as shown in the fig B.[L₁…

A: P=64kN To find axial force and stress in rod 1 and rod 2. Displacement at point A and D

Q: Consider a two-component rod fixed at the left end. The first component (on the left, positioned…

Q: The rigid bar AB as shown in Figure Q1(a) is supported by a steel road AC having a diameter of 22 mm…

A: Diameter of steel rod = 22 mm Cross section area of aluminium block = 2000 mm2 Diameter of pin = 20…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6 mm, and it is
supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 9 mm in diameter.
Assume a = 600 mm, b = 300 mm, h = 400 mm, P = 875 N, and 0 = 55°. Determine the following:
(a) the normal stress in rod (1)
(b) the shear stress in pin B
(c) the shear stress in pin A
D
Answers:
(a) Orod=
(b) Tpin B =
(c) Tpin A =
(1)
a
i
H
i
B
b
MPa
MPa
MPa

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the average shear stress in MPa of the pins Band C on the frame shown in the figure. Note that thesepins are subjected to double shear and have a diameterof 0.5 inch.
A solid steel bar of diameter di = 1.4 in. is enclosed by a steel tube of outer diameter d3 = 2.25 in. and inner diameter d2 = 1.9 in. (see the figure). Both bar and tube are held rigidly by a support at end A and joined securely to a rigid plate at end B. The composite bar, which has length L = 26 in., is twisted by a torque T = 5,100 lb-in. acting on the end plate. Tube A Bar End plate (a) Determine the maximum shear stresses T1 and T2 in the bar and tube, respectively. Round your answers to the nearest whole number. T1 = psi T2 = psi (b) Determine the angle of rotation (in degrees) of the end plate, assuming that the shear modulus of the steel is G = 11.5 × 10° psi. Round your answer to three decimal places. (c) Determine the torsional stiffness kT of the composite bar. Round your answer to the nearest whole. [Hint: Use equations below to find the torques in the bar and tube.] T = T GIp, + G2IP, kT = k-in.
please solve step by step and correctly
The pin-ended wrought-iron pipe shown in the figure below has outer diameter D, inside diameter d, and length L; it supports an eccentric load P based on a safety factor of n. Find the largest allowable eccentricity e. Given: D = 190 mm, d = 170 mm, L = 3.5 m, P = 430 kN, n = 1.4, E = 190 GPa, 0yp = 210 MPa.
Rigid bar ABC shown in the figure is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 5 mm, and it is supported by double-shear pin connections at B and D. The pin at bracket A is a single-shear connection. All pins are 6 mm in diameter. Assume a = 600 mm, b = 250 mm, h = 425 mm, P = 900 N, and 0 = 55°. Determine the the shear stress in pin B. Express your answer in MPa rounded to the nearest hundredths. Answer: Blank 1 D ... (1) B a Blank 1 Add your answer
Neat solution
A split-ring clamp-type shaft collar is shown in the figure. The collar is 50 mm OD by 25 mm ID by 12 mm wide.The screw is designated as M 6 × 1. The relation between the screw tightening torque T, the nominal screw diameterd, and the tension in the screw F i is approximately T = 0.2 F id. The shaft is sized to obtain a close running fit. Findthe axial holding force Fx of the collar as a function of the coefficient of friction and the screw torque.Suppose the collar of Problem 5–80 is tightened by using a screw torque of 20 N ∙ m. The collar material is AISI 1035steel heat-treated to a minimum tensile yield strength of 450 MPa.(a) Estimate the tension in the screw.(b) By relating the tangential stress to the hoop tension, find the internal pressure of the shaft on the ring.(c) Find the tangential and radial stresses in the ring at the inner surface.(d) Determine the maximum shear stress and the von Mises stress.(e) What are the factors of safety based on the maximum-shear-stress and…
Uniform AB brass rod has a rectangular vertical cross section, fixed with support and pin as shown in the figure. Both ends of the rod are free in the vertical direction but rotation in the horizontal direction is prevented. a) Find the b / d ratios at the safe boundaries for the horizontal and vertical axes?b) What would be the safety factor if P = 1.8 kN, L = 7m, d = 60mm and E = 150GPa?
Calculate the average shear stress in MPa of the pins Band C on the frame shown in the figure. Note that thesepins are subjected to double shear and have a diameterof 0.5 inch.