Some questions require you to use the last three digits of your matric card number as input values. For instance : "013" would be your input values where "0" will be labelled as X, "6" as Y and "1" as Z respectively. When entering angles, use the following format : Example#1 : 136° 40' 50" type as 136,40,50 Example#2 : 34° 05' 09" type as 34,05,09 A bearing BA is (350+X)° (40+Y)' (20+Z)" bearing BC is (242+X)° (28+Y)' (24+Z)" C

Some questions require you to use the last three digits of your matric card number as input values. For instance : "013" would be your input values where "0" will be labelled as X, "6" as Y and "1" as Z respectively. When entering angles, use the following format : Example#1 : 136° 40' 50" type as 136,40,50 Example#2 : 34° 05' 09" type as 34,05,09 A bearing BA is (350+X)° (40+Y)' (20+Z)" bearing BC is (242+X)° (28+Y)' (24+Z)" C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Some questions require you to use the last three digits of your matric card number as input values. For instance : Matric Card No. : A20EA0061 "061" would be your input values where "0" will be labelled as X, "6" as Y and "1" as Z respectively. When entering angles, use the following format : Example#1: 136° 40' 50" type as 136,40,50 Example#2: 34° 05' 09" type as 34,05,09 Q4. Observing angles in both faces will eliminate the effects due to the non-perpendicularity of the trunnion axis, thus eliminating what type of errors in the angle observations? (single word answer and use lower case only). Your answer Figure 1 bearing BA is (350+x)° (40+Y)' (20+z)" bearing BC is (242+x)° (28+Y)' (24+z)" в
Determine the coordinates of the centroid of the shaded area. y |15 E 25 30 15 40 50 I 30 90 Dimensions in millimeters Answers: I = i mm y = i mm
Determine the coordinates of the centroid of the shaded area. Answers: De y= 60 30 80 215 Dimensions in millimeters mm 60 50 mm -1X
As an engineer in a construction company, you must design a steel compression member with an effective length of 5 m loaded eccentrically at e = 200 mm, as shown in Figure 2. Due to financial constraints, you need to choose one of the wide-flange shapes according to the properties of rolled-steel shapes as listed in Appendix 1. Use E = 200 GPa and oy = 250 MPa. 200 mm Figure 2 In your design proposal, clearly state the following: i) Evaluate the wide flange steel column that you are selected according to the American Institute of Steel Corporation (AISC) column design standard. Determine the largest load that it can safely support using the allowable stress method.
For the following figure, when * drawing the projection pointer in the direction of the arrow, it will be one of the :following O D О с O A О в A B C D
PROBLEM 4: Determine the centroidal coordinates ( x-bar and y-bar) of the cross-sectional area shown in millimeters. Note: DRAW OR ILLUSTRATE THE SUB-AREAS AND INDICATE THE CENTROID OF EACH SUB-AREA BEFORE ANY NUMERICAL SOLUTIONS.
What type of meridian does the figure represent? W- S Meridian O True Meridian Assumed Meridian Magnetic Meridian Grid Meridian -E
solve the centroid location with the reference lines (just like on the provided picture) provided; find the topmost, leftmost and bottom-most, rightmost for each figure.
Q.1) For the area below, find the coordinates of the centroid. y 300 mm 400 mm 300 mm 300 mm
Note: Replace all zero digits of your ID number by number "2" Problem #5: Use X = Last 3 digits of ID number 5 3 Y = Last 2 digits of ID number 20+C (degrees) A = 4th digit of ID number B = 5th digit of ID number %3D В C = 6th digit of ID number %3D e.g., ID # = 12-3456-789 80+A (Ib) X = 789 Y = 89 In order to maintain equilibrium, A = 4 13. Determine the tension in cable AB. (Ib) B = 5 14. Determine the tension in cable AC. (Ib) C = 6 15. Determine the tension in cable AD. (Ib)
AZIMUTH = 217 please answer the blank tables below and show computation. include also the plot.
What is the area of the below figure if you know x-27.2? (use trapezoidal rule) الجواب 29 27 25 27 25 22