The disk D, which has weight W = 15 lb, starts from rest on an incline when the constant moment M is applied to it. The disk is attached at its center to a wall by a spring of constant k = 7 ft/lb. The spring is unstretched when the disk is at its starting position. The disk rolls down the incline without slipping. Take R = 5 ft, 0 = 25° and g = 32.2 ft/s². Use for the moment of inertia of the disk about G, Ic= /mR²

The disk D, which has weight W = 15 lb, starts from rest on an incline when the constant moment M is applied to it. The disk is attached at its center to a wall by a spring of constant k = 7 ft/lb. The spring is unstretched when the disk is at its starting position. The disk rolls down the incline without slipping. Take R = 5 ft, 0 = 25° and g = 32.2 ft/s². Use for the moment of inertia of the disk about G, Ic= /mR²

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The double pulley shown in the figure is formed by two wheels that are coupled to each other. The complete pulley (formed by the two wheels) has a mass of 15 kg and a turning radius of 110mm. Block A has a mass of 40 kg. If a force of 2 kN is applied to the tied rope of the inner pulley wheel, determine the speed of block A after 3 seconds. At the beginning, the whole system was at rest. Disregard the mass of the string and consider that the moment of inertia (kg.m²) of the complete pulley is given by IP = mko²where m is the mass of the pulley and Ko is the radiusspinning
The spring constants are k1 = 140N / m, k2 = 240N / m and the unstretched lengths of the springs are 0.3 m. If the 6 kg ring is released from rest from point A, calculate its velocity when it reaches point B. According to the given datum line, the total potential energy (Ve) at point A is A = 1116.86 J and the total elastic potential energy (Ve) at point B is B = 370.8 J. Neglect the dimensions of the bracelet. (L1 = 0.90 m, L2 = 1.80 m, h1 = 1.20 m and h2 = 2.40 m)
Find the minimum force P for impending motion of the refrigerator shown, and determine whether it will slip or tip, given:W = 180 lbs, L1 = 4.5 ft, L2 = 3.7 ft, L3 = 2.3 ft, L4 = 1.5 ft, μS = 0.5
The 5 kg cylinder is released from rest in the postion shown in the figure below. Determine the maximum compression xmax of the spring. The stiffness of the spring is 1800 N/m.
Dynamic Lecture: The 2 kg BC ring can only move left and right on the frictionless rigid arm. Ring BC is connected to springs with spring constants k = 300 N / m and k ′ = 200 N / m at points AB and CD. The unstretched length of both springs is 600 mm. Since it is known that the springs are not tensioned and starts from rest, find the velocity of the ring BC at the moment when the external force F is applied 200 mm.
3 - In the figure, the 200-lb crate is being pulled up the slope by the motor M. If the velocity of the point P is 2s³ ft/s (where s is the displacement of the crate), and the coefficient of kinetic friction between the crate and the slope is u = 0.2, what will the towing force applied by M be when the box has moved 10 ft up the slope?
Rod OA rotates counterclockwise at a constant angular rate θ˙ = 4 rad/s. The double collar B is pin-connected together such that one collar slides over the rotating rod and the other collar slides over the circular rod described by the equation r=(1.6cosθ)m. Both collars have a mass of 0.55 kg . Motion is in the horizontal plane. Determine the magnitude of the force which the circular rod exerts on one of the collars at the instant θ = 45∘ Determine the magnitude of the force that OA exerts on the other collar at the instant θ = 45∘
A 1125 kg car and a 2250 kg pickup truck approach a curve on a highway that has a radius of 225 m. (a) At what angle should the highway engineer bank this curve so that vehicles traveling at 65.0 mi>h can safely round it regardless of the condition of their tires? Should the heavy truck go slower than the lighter car? (b) As the car and truck round the curve at 65.0 mi>h, find the normal force on each one due to the highway surface.
(The complete question is in the picture) Consider a 2.0 [kg] box that is attached to two identical springs that are in their relaxed state when the block is centered on the frictionless horizontal floor. The box is pressed to the left and then was released from rest as shown in the figure. If work done by the left spring is Wby spring = 25 [J], what is the speed of the boxas it passes the center x = 0? A. 8.2 [m/s]B. 7.1 [m/s]C. 3.5 [m/s]D. zero
The 4,450kg truck is traveling at 30.50m/s when the brakes on all its wheels are applied, causing it to skid for a distance of 22m before coming to rest. Calculate the constant horizontal force developed in the coupling C, as well as the frictional force developed between the tires of the truck and the road during this time. The combined mass of the boat and trailer is 2,250kg
The collar of mass m is released from rest while in position A and subsequently travels with negligible friction along the vertical-plane circular guide. Determine the magnitude of the normal force exerted by the guide on the collar (a) just before the collar passes point B, (b) just after the collar passes point B (i.e., the collar is now on the curved portion of the guide), (c) as the collar passes point C, and (d) just before the collar passes point D. Use the values m = 0.5 kg, R = 1.0 m, and k = 290 N/m. The unstretched length of the spring is 0.70R.
In the figure, the hanging object has a mass of m1 = 0.420 kg; the sliding block has a mass of m2 = 0.850 kg, and the pulley is a hollow cylinder with a mass M = 0.350 kg, a interior radius R1 = 0.0200 m and an exterior radius R2 = 0.0300 m. Assume that the mass of the rays is negligible. The coefficient of kinetic friction between the block and the surface horizontal is µk = 0.250. The pulley rotates without friction on its axis. The lightweight cable does not stretch and does not slip on pulley. The block has a velocity of vi = 0.820 m / s towards the pulley when you pass a landmark on the table. (a) Use energetic methods to predict its velocity after it has passed a second point, which is at 0.700 m. (b) Find the angular speed of the pulley at the same moment.