The entrance canopy of a building, 2.50m x 6m in dimension, is to be design as a slab. It will carry the following loads: a uniform live load of 2000 Pa, a uniform dead load of 5000 Pa (excluding the slab weight) and a concentrated dead load of 5000 N. per meter of the slab, applied at the extreme end of the support. Design the canopy if one of its longer sides is fixed to the wall and serves as its support. Use the following design properties fo21 MPa, fy-345 MPa, 16-mm-diameter main bars, 10-mm-diameter temperature bars and 20 mm clear cover. Note: Round off your decided dimensions to the next whole number ending in 6 or 6. (00 not increase the size by more than 10mm) Positive Moments: 1. End Spans af discontinuous end is unrestrained b. If discontinuous end is integral with the support- 2. Interior Spans Negative moments: 1. Negative moments at exterior face of first interior support: a. Two spans - b. More than two spans- 2. Negative moment at other faces of interior supports 3. Negative moments at face of all supports for a. Slabs with spans less than 3m - WL'/11 WL/14 -WL'/16 WL'/11 WL'/10 WL/11 WL³/12

The entrance canopy of a building, 2.50m x 6m in dimension, is to be design as a slab. It will carry the following loads: a uniform live load of 2000 Pa, a uniform dead load of 5000 Pa (excluding the slab weight) and a concentrated dead load of 5000 N. per meter of the slab, applied at the extreme end of the support. Design the canopy if one of its longer sides is fixed to the wall and serves as its support. Use the following design properties fo21 MPa, fy-345 MPa, 16-mm-diameter main bars, 10-mm-diameter temperature bars and 20 mm clear cover. Note: Round off your decided dimensions to the next whole number ending in 6 or 6. (00 not increase the size by more than 10mm) Positive Moments: 1. End Spans af discontinuous end is unrestrained b. If discontinuous end is integral with the support- 2. Interior Spans Negative moments: 1. Negative moments at exterior face of first interior support: a. Two spans - b. More than two spans- 2. Negative moment at other faces of interior supports 3. Negative moments at face of all supports for a. Slabs with spans less than 3m - WL'/11 WL/14 -WL'/16 WL'/11 WL'/10 WL/11 WL³/12

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A mechanical support framing system is shown below. The framing consists of steel floor grating over steel beams and entirely supported by four tension hangers that are connected to floor framing above it. It supports light machinery with an operating weight of 4000 lbs, centrally located. (a) Determine the impact factor I from the Live Load Impact Factor, (b) Calculate the total live load acting on one hanger due to the machinery and uniform live load of 40 psf around the machine. (c) Calculate the total dead load acting on one hanger. The floor framing dead load is 25 psf. Ignore the weight of the hangers. Lateral bracing is located on all four edges of the mechanical floor framing for stability and transfer of lateral loads.
Two distributed loads act on the beam AB. If the resultant of this loads is a 2400 N-mcounterclockwise couple (a) Determine the load intensity, w at B and the distance “a” (b) what are thereactions at A and B ?
3/ Pre test :- 1-Determine the resultant of the distributed loads shown in figure and indicate its location from point (A) . 140KN/m 70KN/m 7cm
2. The cross-sectional area of each member of the truss is 1200 mm?. Calculate the stresses in members EF, AF, and BF.
An exterior beam of a floor system having an effective depth of 600mm has a web thickness of 300 mm. The beam has a spacing of 2.4 m on centers. Thickness of the slab is 100 mm. a. Determine the effective with of the flange of the end beam or L-beam having a span of 6 m,b. Determine the effective with of the flange of the T-beam.
4/81 Determine the components of all forces acting on each member of the loaded frame. 5 kN dror 1.5 m 1.5 m В 3 m 3 m 6 m C0meldo sbownin the Cal A Problem 4/81 pailgue 1
4. In addition to the design snow load computed in practice problem 3, the roof of the building in Figure 3 is subjected to a dead load of 16 psf (including the weight of a truss, roof board, and asphalt shingle) on the horizontal plane. Determine the uniform load acting on the interior truss, if the trusses are 6ft-0in on center. roof boards Wood shingles
Problem Number 5 h = 8 m LA 13. Calculate the force at member Gl O a. 13.13kN C O b. 13.13kN T O c. 15.15kN C d. 15.15kN T 1 kN 1 kN J B 1 kN F D E 5 kN 5 kN 5 kN 1 kN 1 kN K -6 panels @ 5 m = 30 m- H
1-3. The floor of a classroom is made of 125-mm thick lightweight plain concrete. If the floor is a slab having a length of8 m and width of 6 m, determine the resultant force caused by the dead load and the live load.
H.W. 3: Double (T) roofing 1200 mm 100 600 10 m I 100 Given: fa-24 N/mm? S = 38 N/mm? Ap = 1000 mm? I=1200 N/mm? Time - dependant losses; L=15% Ye 25 kN/m S.D.L. +S.L.L. = 2 kN/m? Check the beam with respect to the permissible conerete stresses. 150 150 600 150 150
• Use NSCP 2015. Problems: 1.) A floor system consists of a 100mm concrete slab supported by continuous T-beams with 9 m spans, 1.2m 0.c. Web dimensions, as determined by negative-moment requirements, are bw = 280 mm, and d = 500 mm. Concrete cover is 70mm from the centroid of the bars. The beam is subjected to a maximum positive factored moment of 1080 kN-m. Use f'c = 21 MPa and fy = 415 MPa. Calculate the required tension steel area at the point of maximum positive moment.
Two distributed loads act on the beam AB. If the resultant of this loads is a 2400 N-mcounterclockwise couple (a) Free Body Diagram (b) Determine the load intensity, w at B and the distance “a” (c) what are thereactions at A and B ?