The figure shows a hydraulic platform for vehicles made up of two frames equal to the one shown. A 20.0 kN car, with the center of gravity at G, is supported in the position shown. Calculate: a) The force that the cylinder rod EF exerts on each of the members CD b) The horizontal and vertical components of the support reaction C

The figure shows a hydraulic platform for vehicles made up of two frames equal to the one shown. A 20.0 kN car, with the center of gravity at G, is supported in the position shown. Calculate: a) The force that the cylinder rod EF exerts on each of the members CD b) The horizontal and vertical components of the support reaction C

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.124P: The automobile, with center of gravity at G, is parked on an 18 slope with its brakes off. Determine...

See similar textbooks

Similar questions

Find the magnitude of the pin reaction at B caused by the weight W=80lb. Neglect the weights of the members.
The automobile, with center of gravity at G, is parked on an 18 slope with its brakes off. Determine the height h of the smallest curb that will prevent the automobile from rolling down the plane.
Two concrete blocks weighing 320 lb each form part of the retaining wall of a swimming pool. Will the blocks be in equilibrium when the pool is filled and the water exerts the line loading shown?
Compute the magnitude of the pin reaction at B. Neglect the weights of the structural members.
The high-pressure water cock is rigidly attached to the support at D. Neglecting the weights of the members, draw the FBD of the entire assembly and count the unknowns.
The homogeneous bar AB weighs 25 lb. Determine the magnitudes of the forces acting on the bar at A and B. Neglect friction.
Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.
The figure shows a hydraulic platform for vehicles made up of two frames equal to the one shown. A 20.0 kN car, with the center of gravity at G, is supported in the position shown. Calculate: a) The force that the cylinder rod EF exerts on each of the members CD b) The horizontal and vertical components of the support reaction C -3,15m- 0,5 m 1,0 m 0,3 m 0,25 m 1,5m 1,7 m 2,5m
The figure shows the Russel fracture traction device and a mechanical model of the leg. The leg is held in balance in the position indicated by the two weights attached to the two cables. The combined weight of the leg and cast is W=180 N. The horizontal distance between points A and B where the cables are attached to the leg is L=100 cm and the vertical distance is d=5 cm. Point C is the center of gravity of the cast and leg at three quarters of the L measured from point A (3L/4= 75 cm). The angle that cable 2 makes with the horizontal is measured as β=30°. Accordingly, in order for the leg to remain in balance in the shown position; a) Find the tensile force T1 in cable 1. (Write your result in N) Answerb) Find the tensile force T2 in cable 2. (Write your result in N) Answerc) Find the angle α of cable 1 with the horizontal. Response
Q4: of a car غطاء محرك The i Jul. The bonnet is held open at an angle of 60° to the horizontal by a vertical force V applied at one end of the bonnet (shown on the diagram). The long, has a weight of 25 N and its center diagram shows the open bonnet bonnet is 0.90 m of gravity G is 0.35 m from the hinge at O. 1) On the diagram, draw and label the two forces other than V acting on the bonnet. By taking moments about A, Proof that the vertical 2) force V applied at the end of the bonnet is 9.7 N. 3) Calculate the magnitude of the force acting at the hinge ON.
The following figure shows a hollow piston of weight W=50 N and diameter D=3d occupies the position initial displayed. The lateral tube has a diameter d₁=d/2. Find the descent of the piston for the equilibrium position. (b=12 cm, d=8 cm, y=104 N/m³). TBL Agua D d₁
The ramp of a ship has a weight of 107.6 Ib and a center of gravity at G. Determine the cable force in CD needed to just start lifting the ramp, (i.e., so the reaction at Bbecomes zero). Also, determine the horizontal and vertical components of force at the hinge (pin) at A. D 30 6 ft B Determine the vertical component of force at the hinge (pin) at A (in Ib).