The flow rate of water through the pipe system shown in the figure is 25 lit/s under the total head loss of 10m. Assume C = 120 for all pipes. Determine the total head lost and the diameter of pipeline C. Line A L=250m, D = 150mm Line B L=270m, D = 150mm L=200m, D = ? Line D L=500m, D=200mm

The flow rate of water through the pipe system shown in the figure is 25 lit/s under the total head loss of 10m. Assume C = 120 for all pipes. Determine the total head lost and the diameter of pipeline C. Line A L=250m, D = 150mm Line B L=270m, D = 150mm L=200m, D = ? Line D L=500m, D=200mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

SUPPLEMENTARY QUESTION The figure shows two reservoirs connected by a pipe. The discharge rate in the pipe is known to be equal to SN/100 (m2/s) (where SN is the sum of your student number). Calculate the height of the second reservoir (H2), and the pressure head, velocity head and elevation head at point 3 (mid-point of the pipe). HI 300 m H2 datum A = SN/1000 L = 100 x SN (m) D 0.3 m Please solve these question my sn number 31
Q.4. In the system shown in figure, the water flow rate ,Q= 0.5 m3/s and pressure P=20 kPa are required at the point C. Calculate flow directions and flow rates in the pipes and power of the pump required in the system. Draw the energy lines in the system. Note: Neglect the local losses and take f=0.02 in the analysis. B ZA-20 m ZB=40 m 3 zc=4 m ZD=0 m A 2 Li=95 m, L2=120 m, L3=100 m 1 L2= 125m Pump D= 30 cm D k=0.046 mm
Q2 = 10 liter/s DI =? Water D3 = 65mm Tank base area=1 m² rigure 5 (b) A water reservoir (p = 998 kg/m³ ) is being filled through section 1 at Vị = 3 m/s and through section 2 at Q. = 10 litre/s and exit at section 3 at 6.5 m/s which is shown in Figure 5. Calculate the diameter at section 1 so that : i. h is constant, ii. h decrease at 6 mm/s h is constant and section 2 is closed iii. of
The three water-filled tanks shown in the figure below are connected by pipes as indicated. If minor losses are neglected, determine the flow rate in each pipe (+ is out and is into the reservoir) Assume ha = 10 m, hg = 50 m, hc = 0 m, l₁ = 300 m, l₂ = 250 m, and 3 = 500 m. QA = QB Qc= i Elevation = h VA D₂=0.08 m = = 0.020 Elevation = h у в D,= 0.10 m f = 0.015 < D₂ = 0.08 m f = 0.020 Elevation = h с
Water flows inside a solid cylindrical pipe, which narrows as it goes up to a height h (see diagram below). The lower horizontal section has circular cross-sectional diameter d, whereas the upper horizontal section has diameter d/2. Let us denote A to be a point at the lower horizontal section and B to be a point at the upper horizontal section. The flow speed at A and B is uд and u, respectively. The pressure at A and B is PA and PB, respectively. РА UA Oom Ja d d/21 1 UB h (a) Assuming water to be incompressible, show that the flow speed at B is four times the flow speed at A. (b) Use Bernoulli's equation to find the drop in the water pressure from A to B. Express the result in terms of h, uд, the density of water p, and the acceleration of gravity g. (c) Above certain critical height h, vapour bubbles start to appear at the top horizontal section, which hinders water flow through the pipe. Explain why this happens.
The machine C shown in Fig. (3) Is it turbine or pump? What is the water power (kilowatt) associated with this machine? If the flow discharge is 200 lps, PA= 206 kN/m, PB= 690 kN/m2, elevation of A = 67 m and elevation of B = 30 m. Neglect losses. D-300 mm D- 200 mm Fig (3)
Current Attempt in Progress The pump shown in the figure below delivers a head of 250 ft to the water. Determine the power that the pump adds to the water. The difference in elevation of the two ponds is 150 ft. Assume L= 200 ft, D=0.5 ft. - 1.0 Pump K - 1.5 ebow - 5.0 Pipe length - L Pipe diameter -D Pipe roughness -0 = 0.৪ ft-lb/s or i hp
Q3/ The pipe has a different diameter: diameter (Di = 4 m) changes into (Dz = 6 m). The water velocity in the entrance profile was measured (vi = 6 m/s). Calculate the discharge and leave velocity (see figure). Determine also type of flow in input pipe (whether the flow is laminar or turbulent). D, D,
The three water-filled tanks shown in the figure below are connected by pipes as indicated. If minor losses are neglected, determine the flow rate in each pipe (+ is out and - is into the reservoir) Assume ha = 60 m, hg = 90 m, hc = 20 m, e1 = 150 m, l2 = 150 m, and e3 = 300 m. Elevation = B Elevation = ha Elevation = h. D.= 0.10 m = 0.015 D,= 0.08 m D. = 0.08 m %3D = 0.020 = 0.020 QA i QB = i Qc = i > >
Find the discharge through the system shown in the figure. Compute friction loss using the Hazen- Williams equation. 225 ft R-2 Pipe 2: L=5,000 R D=4 in. C=85 125 ft R-1
The three-tanks system in figure are interconnected as shown. Compute the flowrate in each pipe, given: L1 = 2000 m, L2 = 2300 m, L3 = 2500 m; D1 = 1 m, D2 = 0.60 m, D3 = 1.20 m; f1 = 0.013, f2 =0.020, f3 = 0.023.
Write legibly 6. The piping shown in the figure is a parallel-pipe system carrying water at normal temperature. Pressure head at junction X is 76 m, while that at Y is 48 m. If the inflow at junction X is 0.35 cum/s, determine the flow of water at each branch of the loop. Assume C = 120 for all pipes. determine: a. flow in pipe A: ____________m3/s 1b. flow in pipe B: ____________ m3/s c. flow in pipe C: _____________ m3/s