The load F on the rigid body shown below is supported by roller support at B and fixed support at A. Determine the reaction at support A in X-direction. (F = 5.0 KN, a=2.0 m and b = 3.0 m) a b В Meriam,2006 Select one: O a. 0 Ob. 5.00 KN Oc. 2.00 KN Od 1.00 KN Type here to search

The load F on the rigid body shown below is supported by roller support at B and fixed support at A. Determine the reaction at support A in X-direction. (F = 5.0 KN, a=2.0 m and b = 3.0 m) a b В Meriam,2006 Select one: O a. 0 Ob. 5.00 KN Oc. 2.00 KN Od 1.00 KN Type here to search

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Rigid arm AB is subject to a downward force F=270 lbf. It is supported by asquare shaft journal bearing at A and a cable BC.A. Draw a clear and large free-body diagram (FBD) to show all reaction components on AB. Ifany are not engaged, cross them out and add the note “N.E.” for “Not Engaged.” You do NOTneed to set up any equations or solve for any of the reactions.B. Find the unit vector for cable BC.
Determine magnitue, angle of the resultant force and location of it from E, considering the structural element having a seif weight of W KN/m (Where, W=1+3). Also calculate support reactions at A and E by using equilibrium equations. 40 kN 80 kN 50 LN te to E 3m 3m 5m 5m Fig-03 Hints: Self weight acts as uniformly distributed load throughout the length. While calculating moments, the action of total self-weight will be considered to be working right at the mid point of the beam.
Question 3. Consider the diagram below, which is not to scale. A B Given that X 2 m = UDL KN Y kN/m KN C 8m 23 kN and Y = 13 kN/m calculate the reactions at support A and C. Enter your answers in kN correct to three significant figures in the appropriate boxes below. Reaction at A: RA = Reaction at C: Rc = X KN D 10 m
Example -3: The member shows a is pin connected at A and rests agaia R smooth support at B. Determine the horizontal and vertical components of reaction at the pin A. 307 0.75 m 90N m 30 0.5 m 60 N 30 A 90 N m 0.75 m 1m 60 N (b)
Determine the support reactions at the the fixed support, A. Neglect the weight and size of the beam. Given data: Distributed load W=50 N/m; Couple C=160 N-m; and the point load P-780 N acting inclined at an angle of 35 in degree with respect to horizontal. W (n/m) P C (N.m) 1.5 m 2 m 4 m Horizontal force component at A along x, AxD Horizontal force component at A along y, Ay= Moment component at A, Ma= N. m
Solve the following problems completely. Include the FBD with proper labels. 1. The truss is supported by a hinge at A and a roller at D as shown. Find the reactions in the supports. 20 kips C 3 ft D 10 kips - 3 ft 3 ft 2. The truss is supported by a roller at A and a hinge at D as shown. Find the reactions in the supports. B 10 KN 1.5 m 250 A 2 m 2 m 20 KN
Answer FOUR questions ONLY selecting TWO questions from SECTION A. 1. (a) The vertical structure ABCD shown in Figure 1(a) is subjected to a system of coplanar forces and a moment. The structure is simply supported at D with a frictionless pin and is roller-supported at A. i Sketch the free body diagram (FBD). Take moments about D and hence find the reaction force at support A. ii. 35 AN 23m 60 100 km Osm Figure 1(a) (b) An assembly of a steel bar enclosed within an aluminium alloy tube is shown in Figure 1(b). The tube and the bar are of the same initial length. The combination is compressed between two rigid parallel plates by a force of 500 kN. The diameter of the steel bar is 40 mm, and the inside and outside diameters of the alloy tube are 60 mm and 100 mm respectively. The Young's moduli for steel and aluminium alloy respectively are Est = 200 GNM2, EA = 70 GNm?. Find the stresses generated in the steel bar and the aluminium alloy tube. Sael he -Rid pl Figure 1(b)
A hatch door with a center of mass at G is supported by a cable. Identify the support reactions on the door. U 2m > 2 m Check all the possible support reactions on the door, even if some of them are equal to zero due to the loading given. Make sure the reactions in the set you choose do not depend on each other. B FBA at B along the rod A₂ M₁ MB By Az FAB at A along the rod FBC at B along the cable BC B₂
What's the step by step answer of this (with a free body diagram) Determine the magnitude and direction of the support reactions at supports A and B (Hint: Identify the two-force member(s) before drawing the free-body diagram)
A structure member is subjected to force (T = 50 kN). Also, a uniformly distributed load is applied to member CD. If the reaction at roller support is 25 upward. Determine the minimum value of (w)
Determine the reactions at supports for the following Figures. A 40 kN/m -8 m B. 3 m 20 KN 150 kN m
S ! 160-44 Fx= Required information In the structure shown, cable segment ED and member ECF are horizontal. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. By= Bx= Cx= lb 8 in. radius 21 in. 84 in. D E B W 才 G A 60 in. lb FW= 600 lb, determine the force supported by members ABCD, ECF, and GBF. (Include a minus sign if necessary.) The force supported by members ABCD, ECF, and GBF is as follows: Fy= Cy= F T 28 in. 80 in. L lb (Round the final answer to four decimal places.) lb (Round the final answer to four decimal places.) lb (Round the final answer to four decimal places.) lb (Round the final answer to four decimal places.)