The mass Q3// The Lithium bromide (Li Br) - water absorption refrigeration system as TTC flow rate delivered by the solution pump is 0.4 kg/s. The temperatures in the: generator = 105 °C; condenser = 35 °C; evaporator = 5°C; and absorber = 30 °C. Determine: - 1- The mass flow rates of solution returning from the generator to the absorber 2- The mass flow rate of refrigerant flowing in the condenser. 3- The amount of heat in each component. 4- The COP.

The mass Q3// The Lithium bromide (Li Br) - water absorption refrigeration system as TTC flow rate delivered by the solution pump is 0.4 kg/s. The temperatures in the: generator = 105 °C; condenser = 35 °C; evaporator = 5°C; and absorber = 30 °C. Determine: - 1- The mass flow rates of solution returning from the generator to the absorber 2- The mass flow rate of refrigerant flowing in the condenser. 3- The amount of heat in each component. 4- The COP.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter50: Commercial, Packaged Rooftop, Variable Refrigerant Flow, And Variable Air Volume Systems

Section: Chapter Questions

Problem 22RQ: Variable refrigerant flow systems sense the ______and _____of the refrigerant to determine the...

See similar textbooks

Similar questions

Four methods for controlling head pressure in an air-cooled condenser are ______, ______, _______, and
Figure below shows a steam jet refrigeration system that produces chilled water in a flash chamber. The chamber is maintained at a pressure by the steam ejector, which removes the vapor generated by entraining it in the low-pressure jet and discharging into the condenser. The vacuum pump removes air and other non-condensable gases from the condenser shell. For the conditions shown on the figure, determine the make-up water and cooling water flow rates in kg/hr. Show diagrams if there are any
Figure below shows a steam jet refrigeration system that produces chilled water in a flash chamber. The chamber is maintained at a pressure by the steam ejector, which removes the vapor generated by entraining it in the low-pressure jet and discharging into the condenser. The vacuum pump removes air and other non-condensable gases from the condenser shell. For the conditions shown on the figure, determine the make-up water and cooling water flow rates in kg/hr. SHOW THE NEEDED DIAGRAMS FOR THE SOLUTION
Figure below shows a steam jet refrigeration system that produces chilled water in a flash chamber. The chamber is maintained at a pressure by the steam ejector, which removes the vapor generated by entraining it in the low-pressure jet and discharging into the condenser. The vacuum pump removes air and other non-condensable gases from the condenser shell. For the conditions shown on the figure, determine the make-up water and cooling water flow rates in kg/hr.
For the purpose of acting as an air-cooled water chiller, an ammonia refrigerant vapor compression system is deployed. It is functioning with an evaporator temperature of 0 degrees Celsius and a condenser temperature of 40 degrees Celsius. The refrigeration produced by the system is equal to 15 tons.Find out: a. The temperature of the discharge and the mass flow rate of the refrigerant that is being circulated.b. The piston displacement that can be considered theoretical for the compressor.c. The work that can be done by the theoretical compressor.d. The heat that is not allowed to escape through the condenser.e. The Carnot coefficient of performance and the actual COP of the cycle.f. The volume of air that is supplied in the condenser if the air comes in at 30 degrees Celsius and exits at 34 degrees Celsius.g. The LMTD and AMTD of the condenser h. The water flow rate of the chiller assuming that the water enters the evaporator at 10 degrees Celsius and exits at 5 degrees Celsiusi. The…
A steam condenser receives 10 kg per second of steam with an enthalpy of 2570 KJ/kg. Steam condenses into liquid and leaves with an enthalpy of 160 KJ/kg, if cooling water passes through the condenser with temperature increases from 13oC to 24oC. Calculate the cooling water flow rate in kg/sec. pls dont skip anything show all solution including conversion of units
In a certain refrigeration system for low temperature application, a two-stage operation is desirable which employs ammonia system that serves a 40 − ton evaporator at −30°C. The system uses a direct contact cascade condenser, and the condenser temperature is 40°C. Sketch the schematic diagram of the system and draw the complete process on the PH diagram b. The mass flow rate in the low loops in kg/s c. The mass flow rate in the low and high pressure loops in kg/s d. The total work
3.) An ammonia compressor operates at evaporator pressure of 316.02 kPa and a condenser pressure of 1557 kPa. A twin-cylinder compressor with bore to stroke ratio of 0.85 is to used at 1200 rpm. The actual volumetric efficiency is 92% and compression and mechanical efficiency is 78% and 80% respectively. For a cooling capacity of 25 TR, (a) the sketch the p-h diagram labeling the evaporating and condensing temperature and pressures (b) define the all properties of ammonia taken from saturation table. Determine (c) the quantity of cooling water in the condenser in kg/min if the increase in temperature is 8°C, (d) the bore and stroke expressed in cm and (e) the size of the driving motor in hp. Given: h2 = h at 1557 kPa and s2 = s1 1695 kJ/kg
A steam condenser receives 10 kg per second of steam with an enthalpy of 2570 KJ/kg. Steam condenses into liquid and leaves with an enthalpy of 160 KJ/kg, if cooling water passes through the condenser with temperature increases from 13oC to 24oC. Calculate the cooling water flow rate in kg/sec. Show conversion of units pls
Q.1. A refrigeration process with interstage cooling uses refrigerant HFC-134a, and the outlet of the condenser is to be saturated liquid at 40°C. Refer to the following figure for stream numbers in your solution. The pressure of the flash chamber and the intermediate pressure between compressors is to be 290 kPa. The evaporator is to operate at -20°C and the outlet is to be saturated vapor. The flowrate of stream 1 is 23 kg/h. The flash chamber may be considered adiabatic. The compressors may be considered to be 80% efficient. a) What is the power input required to the first compressor? b) What are the flowrates of streams 6 and 7? What is the enthalpy of stream 4? Hot Side 6 5 Condenser 2nd Stage Compressor Throttle Valve 7 Flash Chamber Vapor Phase Only 1st Stage Compressor 8 Throttle Valve Evaporator 1 2 Cold Side
A surface condenser is designed to handle 10000 kg of steam per hour. The steam enters at 0.08 bar abs. and 0.9 dryness and the condensate leaves at the corresponding saturation temperature. The pressure is constant throughout the condenser. Estimate the cooling water flow per hour, If the cooling water temperature rise is limited to 10 degrees * C|
6- The following reading were taken during a test on a surface condenser: Mean condenser temperature = 35°C Hot well temperature = 30°C Condenser vacuum = 69 cm Hg Barometer reading = 76cmHg Condensation rate = 16 kg/min Cooling water temperature inter = 20 °C Cooling water temperature outlet = 32.5 °C Flow rate being = 37500 kg/h Calculate: a- mass of air present per cubic meter of condenser b- quality of steam at condenser inlet c- vacuum efficiency d- condenser efficiency (condenser heat transfer effeteness)