The overhang beam shown in Figure Q2 is pinned at A and rest on a roller at B. The beam supports a uniformly distributed load of A kN/m, a concentrated load of C kN and a couple of moment B kN.m a) Determine the support reaction at point A and B. b) Draw the shear diagrams of the beam. A=16 B= 24 c) 12 A kN/m A B__Q BkN-m -3 m -3 m -2 m - VC KN

The overhang beam shown in Figure Q2 is pinned at A and rest on a roller at B. The beam supports a uniformly distributed load of A kN/m, a concentrated load of C kN and a couple of moment B kN.m a) Determine the support reaction at point A and B. b) Draw the shear diagrams of the beam. A=16 B= 24 c) 12 A kN/m A B__Q BkN-m -3 m -3 m -2 m - VC KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter9: Application Of Influence Lines

Section: Chapter Questions

Problem 2P

See similar textbooks

Similar questions

a. What are the external reaction at the position of the rocker at D, the external horizontal, vertical and resultant reactions at point A? [Solve for a value in kips, with right as positive and left as negative.] b. What is the force in member BC? c. What is the minimum possible diameter of the pin at A which is double shear and the minimum possible diameter of pin B which is single shear? [in inches]
The frame (Figure 1) has dimensions H1 = 4 m , H2 = 3 m , L1 = 5 m , and L2 = 10 m and supports two lateral loads P1 = 10 kN and P2 = 12 kN . a) Use the portal method to determine the shear at J. VJ = ? b) What is the vertical reaction from the ground on the base of the column at AA? Let a positive reaction be pointing upward. Ay = ? c) What is the vertical reaction from the ground on the base of the column at B? Let a positive reaction be pointing upward. By = ?
n the beam shown, taking W1 = 3 kN/m, P1 = 7 kN, P2 = 4 kN, and W2 = 7 kN/m.a) Determine the reaction at "A" b) Determine the reaction at "H" c) Determine the shear at "C" c) Determine the shear at "D" e) Determine the value of maximum moment. f) Determine the value of moment at "G" d) Determine the shear at "F"
For the beam shown, determine the reaction at the roller support when w0 = 6 kips/ft.
In the figure on the right where there is a 50 N single load at point Bof the given rod system, (between AB: 4m / BC: 1m)a) find the support reactions?b) Immediately after support A, just before point Band immediately after and just before the C-bracketFind the cross section effects by cutting?c) Draw the cross sectional influence diagrams.
(a) Assuming that no loads act in Figure P9.16,compute the reactions if support B is constructed 0.48 in.too low. Given: E = 29,000 kips/in.2, I = 300 in.4. (b) Ifsupport B settles _32 in. under the applied loads, computethe reactions.
Calculate the support reaction at roller support C
GIVEN: L1 = 4.5 m W1 = 10 kN/m L2 = 1.2 m W2 = 12 kN/m L3 = 0.5 m L4 = 12 m L5 = 1.5 m A. What is the maximum shear in Beam D-E-B? B. What is the maximum moment in Beam A-B-C?
Compute the reactions and draw the shear and mo-ment curves for the beam in Figure P9.21. In addition tothe applied load, the support at C settles by 0.1 m. EI isconstant for the beam. E = 200 GPa, I = 60 × 106mm4
Given : M1 = 400 kN-m M2 = 500 kN-m M3 = 600 kN-m P = 150 kN w1= 60 kN-m w2 = 120 kN/m a = b = d = 6 m c = 4 m Determine the following: a. The maximum positive shear (in kN). b. The maximum negative shear (in kN). c. The maximum positive moment (in kN-m). d. The maximum negative moment (in kN-m). e. The location of maximum shear from the left end of the beam (in m). f. The location of the maximum moment from the left end of the beam (in m). Kindly Draw the Shear and Moment Diagram. Compute for all of the necessary elements, Include the proper units, use the proper formula and round-off all the answers and final answers to 2 decimal places.
Given : M1 = 4000 N/m M2 = 9000 N/m P = 3600 N (downward) w1= 800 N/m (downward) w2 = 600 N/m (downward) a = 4 m b = c = d = 5 m Determine the following:a. The maximum positive shear (in N).b. The maximum negative shear (in N).c. The maximum positive moment (in N-m).d. The maximum negative moment (in N-m).e. The location of maximum shear from the left end of the beam (in m).f. The location of the maximum moment from the left end of the beam (in m). Kindly Draw the detailed Shear and Moment Diagram. Compute for all of the necessary elements, Include the proper units, use the proper formula and round-off all the answers and final answers to 2 decimal places.
In the beam shown, take W1 = 9 kN/m, M1 = 25 kN-m, and P1 = 22 kN.a) Determine the reaction at "C" b) Determine the reaction at "F" c) Determine the shear at "D" d) Determine the moment at "D" (C-D) e) Determine the moment at "D" (D-E) f) Determine the value of maximum moment