The voltage at the sending side (source) of a transmission line is 1 KV (Vs = 1 KV). The voltage at the receiving side (load side) is also 1 KV (Vr = 1 KV). Vr lags Vs by 300. The transmission line has an impedance of j129.5 ohms. The reactive power supplied by the source is: O A. None of the choices are correct O B. 3864 vars O C. 2072 vars O D. 1036 vars O E. 1932 vars

The voltage at the sending side (source) of a transmission line is 1 KV (Vs = 1 KV). The voltage at the receiving side (load side) is also 1 KV (Vr = 1 KV). Vr lags Vs by 300. The transmission line has an impedance of j129.5 ohms. The reactive power supplied by the source is: O A. None of the choices are correct O B. 3864 vars O C. 2072 vars O D. 1036 vars O E. 1932 vars

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.13MCQ

See similar textbooks

Similar questions

A 220 Ω resistor is in series with an 80 mH inductor. The AC source is 48 at 1 kHz. The power factor is ________. Hint: Draw the circuit and get Vs and Is
2-A resultant current is made of two components: a 10 A D.C. component and a sinusoidal component of maximum value 14.14. The average value of the resultant current is amperes (a) 0 (b) 24.14 (c) 10 (d) 4.14 and r.m.s. value is - amperes (e) 10 (f) 14.14 (g) 24.14 (h) 100
"If lab is equal to 595.8252306 and lb is 344296, the phase sequence is:" O POSITIVE O NEGATIVE
The output voltage waveform of a four quadrant chopper is shown in figure. In the waveform, Vdc is input voltage, D is duty cycle ratio and T is cycle time. DT T. The RMS value of ripple component in output voltage is (A) Vác 2V VD-D (В) V(2D-1) (C) de de (D) V de VD- D? yd
In non-sinusoidal wave sources, the dissipated power in the load is depends on the value of . . Variable Current Average Current Constant Current All-of-them
7- DC Chopper with output voltage of 120V and input voltage of 80V and output power of 240W. Assume lossless chopper. The average inductance current IL is * 2.6 A 3.0A 4.3A
QUESTION 50 RG180B/U is a coaxial cable with a nominal impedance of 95 02 and a capacitance per foot of 15.5 pF/ foot. Determine the inductance per foot of this cable. O a. 140 nH/ft Ob.45 nH/ft O c. 95 nH/ft O d.250 nH/ft
Q2. A series of motor (Load 1) and lighting (load 2) are connected to an AC source as shown in Figure Q2. The AC source, Vs, supplies 415220° V with frequency 50 Hz. Based on this information: 5Ω 100mH : 15 2 Load 1 Load 2 i) Calculate the total load impedance. Vs ii) Calculate the current, I. Figure Q2. Write the waveform expressions in frequency domain for Vs and I. Draw a phasor diagram consists of Vs and / and state the relationship between Vs and I. (ii) (iv) Determine the power factor and calculate the real power, reactive power and apparent power. Establish the power triangle for the load.
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms
The voltage at the sending side (source) of a transmission line is 1 KV (Vs = 1 KV). The voltage at the receiving side (load side) is also 1 KV (Vr = 1 KV). Vr lags Vs by 300. The transmission line has an impedance of j97.5 ohms. The line drop would be: O A. 129.5 O B. 518 V O C. None of the choices are correct O D.O O E. 259 V
3. A sinusoidal voltage is applied to the circuit below. Determine the following: I, Irms, lavg, Ip- 1.0 kN
Consider the system in the figure to the right. The Zbus for the system is given as follows: [j0.411 j0.310 j0.3541 Zbusj0.310 j0.446 j0.333 Lj0.354 j0.333 j0.450] j0.8 1.28/0 ele j0.2 vor j2.0 j0.5 m j0.4 m 2 a) Find the voltage at each bus. b) Find the current drawn by a capacitor having a reactance of 5.0 PU connected from bus 3 to the reference. c) Find the change in voltage at each bus when the capacitor is connected at bus 3. d) Find the voltage at each bus after connecting the capacitor. j1.0 1.20/30°