The voltage source (V1) in the circuit is given by: v(t) = 15 * cos(5x10ft) V If L1 = 1 mH, R1 = 10 02 Determine > V1 a) the complex power supplied by the source b) the power factor of the source c) the complex power for each passive element L1 R1

The voltage source (V1) in the circuit is given by: v(t) = 15 * cos(5x10ft) V If L1 = 1 mH, R1 = 10 02 Determine > V1 a) the complex power supplied by the source b) the power factor of the source c) the complex power for each passive element L1 R1

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.17MCQ: Consider the load convention that is used for the RLC elements shown in Figure 2.2 of the text. A....

See similar textbooks

Related questions

Q: 11. Calculate le and Vce. The transistor is silicon and has a ß of 100. 40 kn 10 kf wwww 9-15 V www…

A: The given circuit is β=100.We need to find IC and VCE.

Q: 9. In a circuit with a 12 volt supply and 42 resistance, the power consumed is 10. What is the unit…

A: Voltage V = 12 V.Resistance Power consumed is given by,

Q: The signal flow graph of a complex system is shown in Figure 2.a. Determine the overall transfer…

Q: Draw the circuit of a JK flip flop using a D flip-flop. Write down its characteristic table. In what…

A: In the given questions we need to design the JK FF using D flip flop.

Q: 2. For the circuit below, find the transfer function H(w) = Vo/Vi.

A: For the given circuit the value of the transfer function of the system needs to be calculated.

Q: Assuming initial conditions to be zero: Part 1: a) Determine the overall open-loop transfer function…

A: The Differential equation of the system is

Q: Q5. The bridge circuit in Figure Q5 below is used to monitor temperature using a thermometer. The…

Q: Evaluate the factors that influence the choice of an appropriate cable for a specific connection.

A: When choosing an appropriate cable for a specific connection, several factors should be considered.…

Q: A 50-hp, 250 V, 1200 r/min dc shunt motor with compensating windings has an armature resistance…

Q: A. Define Commutation. List the method of commutation and explain the external plus commutation…

A: According to the Bartleby Question answer rule if different questions are given I have to solve only…

Q: Find Vo using superposition theorem

A: In the given questions we need to calculate the output voltage.

Q: At 8.543 kHz, the reactance of a circuit capacitor is 9.0 uF. what is the value of inductor? i)…

Q: Find the output current i, in the circuit shown below using superposition, where us=48cos (35t) V.…

Q: S=VI Exercise Q = √5² - P²² 4:13 (L P₂₁ = ReH=2²₂ 2₂H= Хен The following data were obtained when a…

Q: For the block diagram shown below, specify the closed-loop transfer function; R(1) GI HI G2 H2 H3 G3

A: In this question, we need to determine the close loop transfer function. We solve this problem using…

Q: In an Inverting Op Amp, what formulas help you find Vin and Vout?

A: The objective of the question is to identify the formulas that can be used to calculate the input…

Q: Determine the total resistance for the circuit, given: R₁ = 2102, R₂ = 24 02, R₂ = 62, and R₁ = 190…

Q: A. A step down dc chopper is connected to an R = 5 2 and L = 10 mH. The de supply voltage is 100 V.…

A: Given , supply voltage is Vin .Output voltage is Vout

Q: 15. A magnetic field given in the spherical coordinates by 1 H = (² sin ea, ² sin 0 a, +cos e cosa,…

A: A magnetic field in spherical coordinates given byis applied to the following magnetic materials…

Q: Determine the voltage dropped on R3, given: E₁ = 236 V, R₁ = 39 , R₂ = 75 , and R₂ = 150 (Round the…

Q: For a PLC with the SLC 5/05 CPU module, SLC 501 CPU SLC 5:02 CPU SLC 500 CPU FORCE O a. Downloading…

A: The given PLC with the SLC5/05 CPU module is shown below.We need to choose the correct option…

Q: What are the beam angles for Lamp #1 and Lamp #2 respectively?

A: The given diagram is shown below.We need to determine the beam angles for Lamp #1 and Lamp #2…

Q: 24 V(+ Voc = Isc = RTh RL 4 ΚΩ = 12 ΚΩ ARL в Β mági + Voc V mA Vx Using R₁ as the load in the…

A: The circuit diagram,

Q: Question 8. 12V I₁: A R₁ R₂ 5 V C R₂ Consider the circuit below, where the capacitor is uncharged,…

A: The circuit diagram,The resistors,

Q: H.W4 The single-phase full wave controlled rectifier has a purely resistive load of R and the delay…

A: IL=10APL=100Wα=2π3Load resistance is RAsked to find the following:EfficiencyRipple factorPIV of…

Q: H.W2 The single-phase half wave rectifier has R-L load with R= 59 and L= 6.5mH. The input voltage…

A: Given R-L load with R= 5 ohms and L= 6.5 mH. The input voltage Vs = 220 V at 50 Hz

Q: + 41. R = 60 www VR E = 120 V 220° ZT + Fig. 2 Xc = 30 02 Ω HE + VC Vc

Q: Match the transfer function with step response

A: The transfer functions of the systems are given bya. T(s)=289s2+3.4s+289.b. T(s)=5s+5.c.…

Q: 5 Find the steady-state expression for v, in the circuit = = 200 cos 5000t mA. of Fig. P9.26 if i g…

A: Using current division rule, find the current through the 240 ohms resistor. By ohms law , voltage…

Q: If the field current of a shunt wound d.c. motor is halved, what effect will this have on the speed?…

A: Dc shunt motor is a constant flux motor.Asked to find the speed when the field current is reduced by…

Q: Determine the voltage dropped across R₁, given: Ę₁ = 176 V, R₁ = 24, R₂ = 262, R₂ = 112, and R₁ = 18…

A: The given circuit isET=176 V.R1=24 Ω.R2=26 Ω.R3=11 Ω.R4=18 Ω.We need to find the voltage drop across…

Q: d. _Determine the current is for the network of next figure. Result must be shown in Rectangular…

Q: Analyze the different semiconductor technologies, such as silicon, germanium, and gallium arsenide

A: In the given questions we need to Analyze the different semiconductor technologies, such as silicon,…

Q: Determine the total power consumed in the circuit, given: E₁=160 V, R₁ = 47 2, R₂ = 10 , and R3 =…

Q: For the logic gate network shown below, select which of the following expressions is the right one.…

Q: 2. For the circuit below, find the transfer function H(w) = Vo/Vi. + Vi C ell R

A: The given circuit isWe need to find the transfer function H(ω)=VoVi using phasor approach.

Q: Question 7: Look at this PLC off-delay circuit and explain and describe how it will function, in…

A: In industrial automation, a PLC, or Programmable Logic Controller, is a specialized computer used to…

Q: An analog voltage in the range 0 to 10.8 V is divided in 16 equal intervals for conversion to 4-bit…

A: Range of voltage is given as,0 to 10.8 V.Maximum voltage is given as, Number of interval given as, n…

Q: Consider the position control system given below. Determine the value of K such that the steady…

Q: Home Work For the network of Figure below, determine Avand Ai.

Q: etch by hand the bode plot of the transfer function below. Clearly explain your reasoning. H(o)= 0.2…

A: In this question, we need to draw the bode plot of the given transfer function.

Q: Calculate current across the capacitor shown in Fig. P8.6 if the voltage input is v1(t)=30 cos…

Q: Assuming initial conditions to be zero: Part 1: a) Determine the overall open-loop transfer function…

A: The Differential equation of the system is

Q: B. A three-phase full converter bridge is connected to a 3-phase 400 V, 50 Hz, supply having a…

Q: Use source transformation to find the voltage Vx in the given circuit where /= 10 A. 40 V 892 www +…

A: In this question, we need to determine the voltage Vx using the source transformation.

Q: How much current will flow into the resistor in this condition? RL R-4.0 ohms L-1.2 m V B 2 T…

A: Resistance Length L = 1.2 m.Magnetic field B = 2 T.Velocity v = 0.713 m/s.Driction into page of…

Q: In Figure 1, the 3-phase source has a line-to-line voltage of 440 volts. The details of the…

A: The line-to-line voltage of 3-phase source is VL=440 V.Two three-phase Y- and delta-connected loads…

Q: Consider the following causal difference equation, which operates at a sample rate of 8 kHz: 5 3…

A: We have the following causal differential equation, which operate at the samplw rate 5 hz.d) plot…

Q: Find 4 and 6 poles for a butterworth filter. Use the S-plane circle with a radius equal to the…

A: A Butterworth filter is a type of signal processing filter designed to have a frequency response…

Q: why does Ic vary with Vce for transistors

A: To discuss-:why does Ic vary with Vce for transistorsIc is thе collеctor currеnt in a transistor,…

Concept explainers

Distribution System

The final stage in the delivery of the electric power is the electric power distribution system. From the transmission system to the individual customers it carries electricity. The distribution system is connected with the transmission system and is used to lower the voltage of the transmission to medium voltage in the range of 2 kV to 35 kV with the help of transformers. This medium voltage to the distribution transformers located near the customer's premises is carried by the primary distribution system lines. These distribution transformers in turn lower the voltage to utilization voltage used in lightings, household appliances, industrial equipments etc. Through secondary distribution lines often several customers are supplied from one transformer. It is through service drops, the commercial and residential customers are connected to the secondary distribution system lines. Customers who demand a larger amount of power can be connected directly to the primary distribution system level or the sub-transmission level.

Question

The voltage source (V1) in the circuit is
given by:
v(t) = 15* cos(5x10¹t) V
If L1= 1 mH, R1 = 100
Determine
V1
a) the complex power supplied by the source
b) the power factor of the source
c) the complex power for each passive element
L1
R1
www

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Determination of given parameters,

VIEW

Step 2: Calculation of current,

VIEW

Step 3: Calculation of complex power,

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 15 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Suppose there is no power lost in the wires used to distribute power in a typical home. The following voltages and currents are calculated for thecomponents:va=120 V ia=−10 Avb=120 V ib=10 Avf=−120 V if=3 Avg=120 Vvh=−240 V ih=−7 AIf the power in this modified model balances, what is the value of thecurrent in component g?
ANSWER SHOULD BE: V1 = 11.33V, V2 =26.67VSHOW THE STEP-BY-STEP SOLUTION
In the circuit shown, an ideal source provides a current i (t) =1.25 cos (5t - 15 °) A, to a load. a) What is the complex power supplied to the load when R = 20 Ω and L = 3 H? b) What are the values of R and L that would cause the source to supply 11.72 + j11.72 VA?
Consider the following parallel connected loads with the following characteristicsL1: 1.2kW purely resistiveL2: 2.5kW, 0.8 pf lagL3: 1.8kW, 0.72 pf lag Find the total real power (in kW) consumed by the parallel loads Find the total reactive power (in kVAR) consumed by the parallel loads Find the net power factor lag of the parallel loads Compute for the reactive power (in kVAR) needed to be supplied by a capacitor to increase the power factor to 0.92 lag.
Define 1 ?AC power, power factor and power triangle A series circuit has R=10 Ω, L= 50 mH and C= 100µF is supplied with 200V,50Hzsupply. Find (i) impedence (ii) current (iii) power(iv) power factor (v) voltage drop acrosseach element
TOPIC: Ohm's Law, Power and Generating Direct CurrentDirect Current Circuit AnalysisInductor, Capacitor, Generating Alternating Current Please Answer: Itotal I2 I1 Vtotal
2- Voltage applied to a system composed of two pure elements connected in parallel. U = 141.1 sin (6280t-40) and I = 28.28 sin (6280t + 20). a- Find these two element values? b- Find the power spent on my site?
Two balanced Y-connected loads in parallel, one drawing 15 kW at 0.6 power factor lagging andthe other drawing 10 kVA at 0.8 power factor leading, are supplied by a balanced, three-phase,480-volt source.d. ∆-connected capacitors are now installed in parallel with the combined load. Whatvalue of capacitive reactance is needed in each leg of the ∆ to make the source powerfactor unity? Give your answer in W.e. Compute the magnitude of the current in each capacitor and the line current from thesource
A resistor of 10ohm and an inductor of 0.2 henry are connected in series and given a supply of 230 V, 50 Hz, then (i) Inductive reactance (ii) Impedance (iii) Current (iv) Power factor (v) True power (vi) Reactive power and (vii) find the apparent power
Question oneA balanced star connected load comprises of 20 ohm resistance and 0.07 Henry inductance in each branch. If the load supplied with 415V at 50Hz, calculatea) the line currentb) the power factorc) the total power supplied to the load PLEASE FOLLOW THIS APPROACH TO SOLVE THE QUESTION. THANK YOUStep OneDeduce the inductive reactance.STEP TwoWrite down a rectangular expression for the impedance per branch.STEP ThreeConvert the rectangular expression into polar expression.STEP FourBecause impedance will be involved in the analysis deduce the phase voltage.STEP FiveSolve for the phase current and hence the line current.STEPVSixUse the phase angle of the current to deduce the power factor. STEP SevenFind the apparent power.
ChatGPT 3.5 You A balanced load is connected in star across a 3 phase 415V 50Hz supply. The load consists of a coil of resistance 25 ohms and inductance 0.5 henry in parallel with a pure resistance of 28 ohms and a pure capacitor of 60 microfarads capacitance ib each branch Calculate I. The line currents Ii. The overall power factor. iii. The power delivered from the supply. iv. The power dissipated in the resistors and coils. v. The current in the neutral supported by a reason why its value is that deduced ?
Given the circuit, solve for:a. Total currentb. Total apparent powerc. Total real powerd. Total reactive powere. pf of the circuitPlease, I need a complete solution. I promise to give it a thumbs up! :)