The water from the cistern tank is pumped over a hill through a pipe 900 mm in diameter and a pressure 1 kg/cm² is maintained at the pipe discharge where the 85 m from the pump centerline. Pump has a static suction lift of 5 m. The pump capacity is 1500 liters per second. Neglect the friction losses and the cistern tank source) is open to atmosphere. Determine : • Total Dynamic Head

The water from the cistern tank is pumped over a hill through a pipe 900 mm in diameter and a pressure 1 kg/cm² is maintained at the pipe discharge where the 85 m from the pump centerline. Pump has a static suction lift of 5 m. The pump capacity is 1500 liters per second. Neglect the friction losses and the cistern tank source) is open to atmosphere. Determine : • Total Dynamic Head

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A centrifugal pump is used to pump water (1000 kg/m³) to a height of 10m, the water splashes down back into the tank. The diameter of the impeller of the pump is 145 mm, the pump speed is 2900 rpm. The equation to calculate the flow V in the valve depending on the pressure drop differential pressure (dp) in the valve isV = 4 * sqrt (dp), whereas V is in m³/h and dp in bar. Please estimate the water flow.
The impeller of the centrifugal pump is 350 mm diameter, and the width of the blade passages at outlet is 18 mm. A pump, which runs at 16.6 rev/s, is mounted so that its centre is 2.4 m above the water level in the suction sump. It delivers water to a point 19 m above its centre; the friction loss in the suction pipe is 68 Q² meter and that in the delivery pipe is 650 Q² meter where Q in m3/s is the rate of flow. The blades themselves occupy 5% of the circumference and are backward facing at 35° to the tangent. At inlet, the flow is radial and the radial component of velocity remains unchanged through the impeller. Assuming that 50% of the velocity head of the water leaving the impeller is converted to pressure head in the volute, and that friction and shock losses in the pump, the velocity heads in the suction and delivery pipes are negligible, calculate the following:The flow rate, m3/s, of the pump. Manometric efficiency, in %, of the pump.
The impeller of the centrifugal pump is 350 mm diameter, and the width of the blade passages at outlet is 18 mm. A pump, which runs at 16.6 rev/s, is mounted so that its centre is 2.4 m above the water level in the suction sump. It delivers water to a point 19 m above its centre; the friction loss in the suction pipe is 68 Q² meter and that in the delivery pipe is 650 Q² meter where Q in m3/s is the rate of flow. The blades themselves occupy 5% of the circumference and are backward facing at 35° to the tangent. At inlet, the flow is radial and the radial component of velocity remains unchanged through the impeller. Assuming that 50% of the velocity head of the water leaving the impeller is converted to pressure head in the volute, and that friction and shock losses in the pump, the velocity heads in the suction and delivery pipes are negligible, calculate the following: The flow rate, m3/s, of the pump. Manometric efficiency, in %, of the pump.
A centrifugal pump has an impeller of diameter 250 mm whose width at the exit is 50 mm. The flow velocity through the impeller having radial vanes is constant at 3.0 m/s. The speed of the pump is 1200 rpm and manometric efficiency is 85%. Find the head developed by the pump (m) 19:54 /
Show complete solution and formulas used. Show the schematic diagram too. Calculate the required pipe diameter to avoid cavitation, if the pump delivers Q = 30US gallon/min water from a closed tank, where the pressure (above the water level) is p = 40kPa. The equivalent length of the smoothened concrete pipe on the suction side is 12m while the suction flange of the pump is 8m below the water level. The vapour pressure at the given water temperature is 2.8kPa. The required net positive suction head is NPSHr = 3.2m.
The figure shows a portion of a fire protection system in which a pump draws water at 60°F(v=1.21 x10-5 m² from a reservoir and delivers it to a point B at the flow rate of 1500 gal/min. Calculate the required height of the the water level in the tank in order to maintain 5.0 Psig pressure at point A
Determine the NPSH available for the system shown. The pump takes water at 30 ° C. The system is installed at sea level. The pump is at 2 m above the water level. The pipe measures 6 m and the diameter of 5 cm. The tubing has a sharp edge entry and the elbow is 90 ° threaded. The flow that the pump moves is 90 liters per minute. The material of the tubing is galvanized iron.
A pump at an elevation of 300m is pumping 0.05 m³/s of water through 2.4 km of 150-mm pipe to a reservoir whose level is at an elevation of 380m. What pressure will be found in the pipe at a point where the elevation is 335m above the datum and the distance (measured along the pipe) from the pipe is 970m? Compute the capacity of the pump. Use E/D= 1.5384x10-³
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.1. Find the maximum allowable speed to operate the pump
A 120° reducing bend is placed in a horizontal plarre such that the inlet is inclined 30° to the horizontal. The diameter at inlet is 200 mm and that at exit is 100 mm. The flow rate of water through the bend is 2000 Ipm and the flow is frictionless. For a pressure head of 200 mm of Hg (gauge) at inlet, find the net force on the bend in magnitude ad direction.
A centrifugal pump with radial inlet (alpha4 = 90°) operates with water at a flow of 0.3 m3 /s. The rotor diameter is 250 mm and the blades it is 30 mm wide at the outlet. Assume that the blades are radial at the exit. Determine the theoretical height considering infinite number of blades and power required when the pump runs at 800 rpm.
A pump has a specific speed of 42 and 600 rpm when it delivers 0.01 m3/s. find the head developed by the pump. Answer: 1015.29 ft