number 1.1 * Your answer is incorrect.Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 4450 mm² and an allowable normal stress of 165MPa. Bar (2) has a cross-sectional area of A2 = 4400 mm² and an allowable normal stress of 100 MPa. Assume x₁ = 2.1 m, x₂ = 3.4 m, y₁= 1.1 m, and y₂ = 4.1 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowablenormal stress.3/₁AAnswer: Pmax(1)B765.67·x₂.CkN3/₂

According to the given data σAB=165 MPa and AAB=4450mm2 σBC=100MPa and ABC=4400mm2 We need to find…

Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 4450 mm² and an allowable normal stress of 165 MPa. Bar (2) has a cross-sectional area of A₂ = 4400 mm² and an allowable normal stress of 100 MPa. Assume x₁ = 2.1 m, x2 = 3.4 m, y₁ = 1.1 m, and y₂ = 4.1 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. = 3/₁ A Answer: Pmax (1) B i 765.67 (2) KN y/₂

Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A₁ = 4450 mm² and an allowable normal stress of 165 MPa. Bar (2) has a cross-sectional area of A₂ = 4400 mm² and an allowable normal stress of 100 MPa. Assume x₁ = 2.1 m, x2 = 3.4 m, y₁ = 1.1 m, and y₂ = 4.1 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. = 3/₁ A Answer: Pmax (1) B i 765.67 (2) KN y/₂

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.3.10P: A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in...

See similar textbooks

Similar questions

Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
A two-story building has steel columns AB in the first floor and BC in the second floor, as shown in the figure. The roof load P:equals 400 KN, and the second-floor load P-, equals 720 kN. Each column has a length L = 3.75 m. The cross-sectional areas of the first- and second-floor columns are 11,000 mm" and 3900 mm", respectively. (a) Assuming that E = 206 GPa. determine the total shortenings aof the two columns due to the combined action of the loads Ptand P,. (b) How much additional load P0can be placed at t he top of t he column (point C) if t he total shortening: SACis not to exceed 4.0 mm?
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
A steel pad supporting heavy machinery rests on Four short, hollow, cast iron piers (see figure). The ultimate strength of the cast iron in compression in 50 ksi. The outer diameter of the piers is d = 4.5 in, and the wall thickness is t = 0.40 in. Using a factor of safety of 3.5 with respect to the ultimate strength, determine the total load P that can be supported by the pad.
A steel bar has a square cross section of width b = 2.0 in. (sec figure). The bar has pinned supports at the ends and is 3.0 ft long. The axial forces acting at the end of the bar have a resultant P = 20 kips located at distance e = 0,75 in, from the center of the cross section. Also, the modulus of elasticity of the steel is 29,000 ksi. Determine the maximum compressive stress max, in the bar. If the allowable stress in the steel is 18,000 psi, what is the maximum permissible length Lmaxof the bar?
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
A slightly tapered bar AB of solid circular crass section and length L is supported at end B and subjected to a tensile load P at the free end A. The diameters of the bar at ends A and B are dAand dB. respectively. Determine the length of the bar if the elongation of the bar due to the load P = 45 kips is 0.02 in. Assume that E = 10,400 ksi.
A symmetrical framework consisting of three pin-connected bars is loaded by a force P (see figure). The angle between the inclined bars and the horizontal is a = 52°. The axial strain in the middle bar is measured as 0.036. Determine the tensile stress in the outer bars if they are constructed of a copper alloy having the following stress-strain relationship:
A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 3650 mm2 and an allowable normal stress of 100 MPa. Bar (2) has a cross-sectional area of A2 = 4150 mm2 and an allowable normal stress of 165 MPa. Assume x1 = 2.3 m, x2 = 2.8 m, y1 = 1.3 m, and y2 = 3.4 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.
Two solid bars support a load P as shown. Bar (1) has a cross-sectional area of A1 = 4850 mm2 and an allowable normal stress of 150 MPa. Bar (2) has a cross-sectional area of A2 = 4750 mm2 and an allowable normal stress of 140 MPa. Assume x1 = 2.2 m, x2 = 3.4 m, y1 = 1.1 m, and y2 = 2.7 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.Answer: Pmax = Enter your answer in accordance to the question statement kN
An axial load of 100 kN is applied to a flat bar 20 mm thick, tapering in width from 120 mm to 40 mm in a length 0f 10 m. Assuming E=200 GPa, determine the total elongation of the bar.