VO2 (mL. kg. min ¹)-(0.1. S)+(1.8. S. G) 3.5VO2 (mL. kg¹. min ¹1)-(0.2.5) + (0.9. S. G) 3.5VO2 (ml. kg¹. min¹)-((10.8. watts)/BM)+7Where S-velocity (m.min)G-gradient (expressed as a decimal, so 5% -0.05)During working maintain 4 d.p. Round answer to whole numbers.During working maintain 4 d.p. Round answer to whole numbers.What is the caloric expenditure for a 90kg client who cycles at 250W for 10 minutes?O a. 167 k.calO b. 160 k.calO c. 37 k.calO d.67 k.calO e. 173 k.calHand written plz

Write the expression of VO2. VO2=10.8wattsBM+7

Answered: What is the caloric expenditure for a…

What is the caloric expenditure for a 90kg client who cycles at 250W for 10 minutes? O a. 167 k.cal O b. 160 k.cal O c. 37 k.cal O d. 67 k.cal O e. 173 k.cal

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

work due to spring (N.m) angular velocity in position (2) (rad/s)
1) Between two sections in a vessel, a fluid moves in a steady flow manner. At entrance: A1=20 m2, P1-1300 kgm/m. At exit: A2=10 m2, v2=0.00125 m/kg, ūz=3 m/min. Determine the following: a) m, in kg/min b) ũj in m/min 2) A compressor draws in 0.5 kgm/s of air with 7 m/s speed, 100 kPa pressure, and 0.95 m³/kgm: The air leaves at 5 m/s, 700 kPa and 0.19 m /kgm. The internal energy of the air leaving is 90 kJ/kgm greater than that of the air entering which is 70 kJ/kgm. The coolant absorbs heat from the air at the rate of 58 kW. Determine the work in kW.
Q1. a) In an adult, the aorta's radius is normally 1.5 cm and blood moves through it at the average velocity of 30 cm/s. If a typical capillary vein has a constant radius of 5 x10m and blood passes through them with a velocity of 0.1 cm/s, approximately how many capillaries are needed in a body? b) Benzene at 1 atm and 80°C enters the pipe system given in the below figure, with a Reynolds number of 130000 and leaves the system at 60°C. Assuming that diameters of the pipes at the exit are equal to each other, calculate the Reynolds number on one of the exit pipes (density of liquid benzene at 80° C= 813 kg/m' and at 60°C = 835 kg/m³). 3 in st 80 5 in st 80 3 in st 80
.5 kg of an ideal gas undergoes an isentropic process from 657 kPa gage and a volume of 0.017 cubic meter to a final volume of 0.1 cubic meter. If Cv = 0.384 kJ/kg-K and Cp = 0.52 kJ/kg-K, calculate: a) the final temperature in deg. C b) the final pressure in kPa c) the change in enthalpy in kJ d) the work nonflow in kJ
9) Which of the following is not the intensive property (a) pressure (b) temperature (c) density (d) heat (e) specific volume. 10) What is the change in the internal energy of a gas during an adiabatic process? a) AU = -W b) AU = Q c) AU = 0 d) AU = -Q e) AU = W 11) In a system undergoing adiabatic compression, what are the values of internal energy and heat if work done on the system is 3.5 kJ? a) Internal energy is 0 and heat is 3.5 kJ b) Internal energy is 0 and heat is 3.5 kJ c) Internal energy is 3.5 kJ and heat is 0 J
AND E 1 32% Ô 20:22 H+ flow rates of these two fans? c) A system is equipped with two pressure gages and a manometer, as shown below. For Ah= 8 cm, determine the pressure difference AP=P2-Pı d) The pressure of water flowing through a pipe is measured by the arrangement shown below. For the values given, calculate the pressure in the pipe. Air Ah Manometer fluid SG = 2.67, Oil SG = 0.87 %3D P1 P2 20:22 2/2
Complete the table. a. 355 km/s cm/s m/ms b. 1228 g/L g/mL kg/ML c. 554 mK/s K/s uK/ms d. 2.554 mg/mL g/L ug/mL
C. A substance has a total mass of 12.52 lbm and is under gravity at 30.5 ft/s². p (kg/m³) y (kN/m³) W (lbf) v (ft³/1bm) 1 2 3 920.00 6.50 x 10-3 SG 2.25
isobaric process A certain gas, with cp = 0.529 Btu/lb -R and R = 96 ft lb/lb -R, expands from 5 cu meters and 80 deg F to 15 cu meters while the pressure remains constant at 15.5 psia. Compute the ff: a) Final Temperature, b) change in enthalpy, c) change in internal energy, d) change in entropy and e) non-flow work.
If a piston-cylinder system has V = 0.8m^3 of saturated water vapor at P1 = 250 kPa, at which the piston is sitting on a number of stops. The heat is slowly transferred to steam until the piston begins to move off of the stops at a pressure of P2 = 300 kPa, the heat transfer to steam continues until the volume doubles. a) draw the control volume, with assumed direction of work and heat transfers b) draw P-v diagram c) find final temperature
What would be the resultant force F of the triangular distributed load and its location d measured from point A.
Q1: If a calorimeter is not assumed to be adiabatic, how would one calculate the heat transfer? Guide Questions: What are the parameters to be considered and the equations to be used? What law of thermodynamics does this transfer of heat to the surroundings touch? Is an adiabatic system automatically considered as a closed system? Please help me understand by also attaching a reference/book/journal article. This would help me in my essay. Thank you.