Where D - HORIZONTAL DISTANCE a = the angle subtended by the targets. Example 2-11: A 2-m long subtense bar was first set up at A and subsequently at B, and the subtended angles to the bar, as read from a theodolite positioned somewhere along the middle of line AB, were recorded as e°24'51" and Determine the length of AB. e°20'30", respectively.

Where D - HORIZONTAL DISTANCE a = the angle subtended by the targets. Example 2-11: A 2-m long subtense bar was first set up at A and subsequently at B, and the subtended angles to the bar, as read from a theodolite positioned somewhere along the middle of line AB, were recorded as e°24'51" and Determine the length of AB. e°20'30", respectively.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

h er 6. Calculate the height difference of level surveying and the elevation of point B in Tab. 2-6. Station number Surveying point HA I II a IN BM. A TP₁ TP₁ TP₂ TP₁ TP, TP₁ B TP MSL Σa-2b= II Back rod reading (mm) 1780 1651 1167 b₂ 1726 Level surveying record Front rod reading (mm) TP₂ E 1200 1050 1789 1448 TP, & (height difference) (m) + da TP Tab. 2-6 H(m) 20,000
C ... 1m 6m A 30° Water Area of segment of = (1/2)r²[(n/180)0 – sine] a circle %3D Gate ACB is in a shape of a sector of a circle whose radius is 6m as shown. Determine the following: a) Horizontal component FH is Blank 1 KN b) Vertical component Fv is Blank 2 KN c) Distance of FH from point "C" is Blank 3 m c) Distance of Fv from point "C" is Blank 4 m B.
If the 4 holes in the drawing below are produced at .410" in diameter, what is the total positional tolerance of the holes? O .040 O .020 O .035 D O .410 Ø3.000 .020 45° 4X Ø.395-.430 Ø.500-.510 0.020MABMCM +0.010M ADM -.375-.395 +.000MABM C Ø2.000 A 0.005MA B
A. TACHEOMETRY 1. A transit is set up at a distance back of the zero end of a level base line 240 m. long. The base line being marked by stakes at every 30 m. A rod is then held at successive stations along the base line. The stadia intervals at each location of the rod are tabulated below. It is required to determine the stadia interval factor of the instrument. Distance Stadia Distance Stadia Intercept Intercept 30 0.297 150 1.482 60 0.591 180 1.776 90 0.885 210 2.073 120 1.188 240 2.367
A 3 meter long subtense bar was first set up at A and subsequently at B, and the subtended angle to the bar, as read from a theodolite position somewhere along the middle of the line AB, were recorded as 3deg 5’00” and 2deg 6’00". Determine the length of line AB. a. 125.69 m b. 137.58 m c. 256.12 m d. 165.69 m
Find div F and curl F if F(a, y, z) = 5y°z'i – 14x°2°j – 5xy'k. %3D | div F= curl F=
Read the question carefully and give me right solution according to the question. Urgenttttttttt please Given angle are 47o
TP1 4.20 6.02 21+80 5.80 22+00 5.95 22+50 6.05 BM2 5.83 451.06 3. The bearing of line AB is N 50°16'08" E, and the bearing of line AC is N 64°23'32" W. What is angle +C BAC? 4. Suppose that a line has been observed 10 times using the same equipment and procedures. The results are shown below and it is assumed that no mistakes exist, and that the observations have already been corrected for all systematic errors. Compute the most probable value for the line length and the standard deviation. 64.25.32 Length (ft) 538.57 538.39 538.37 538.39 538.48 538.49 538.33 538.46 538.47 538.55 5. For the section shown, sections S1 and S2 are spaced 100 ft apart. The dimensions of Si and S2 are as given in the table below. Determine the area of the midsection in a prismoidal computation of the volume of dirt removed. Section 40.0 ft 5.67 ft 0.5 50.0 ft 7.14 ft 0.5 S1 S2
In the accompanying sketch, A, B, and C are three known control stations and P is the position of sounding vessel which it to be located. B A AB = 6708.40 m AC = 6925. 50 m ZBAC = 112°45' 25" %3! C = 25°32'40" : 45°35'30" Determine the following: 1. Angle ACP in deg-min-sec 2. Length AP in meters 3. Length of BP in meters 4. Length of CP in meters 5. Angle BAP in deg-min-sec 6. Angle CAP in deg-min-sec
FIND CENTROID (C.G.) FIND Ix WI2X40 WIZX40 Ix= 307 im" A- 11.7 in 307 int WT 6X20 A-5.84m エx14.イm 1.09 im. WIZX40 とWTGX20 21 の

On the drawing below, the virtual condition of the 4 holes is? O .450 .375 O.395 O .020 D O .430 Ø3.000 .020 0 10 45° 4X Ø.395-.430 Ø.500-.510 Ø.020MABMCM +0.010M ADM Ø2.000 .375-.395 4.000MABM C A 0.005MA B
A student was asked to make a line 500-m long using a 25 m tape that is of standard length at a temperature of 28 deg. C. If the average temperature is 12 deg. C, what is the required measurement? Assume a = 0.0000116 m/m-deg. C. O a. 499.0533 Ob. 500.0928 O c. 500.0467 Od. 499.9072