Write a subroutine to copy the content of register R0 and R1 into the register R20 and R21 respectively. Initialize the Stack pointer to the last location of the RAM and preserve the content of the register R20 and R21 using the stack during the subroutine call. Illustrate the content of the stack and the stack pointer during the subroutine execution.

Write a subroutine to copy the content of register R0 and R1 into the register R20 and R21 respectively. Initialize the Stack pointer to the last location of the RAM and preserve the content of the register R20 and R21 using the stack during the subroutine call. Illustrate the content of the stack and the stack pointer during the subroutine execution.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

In simple words, describe the stack pointer register.
3. The table below represents a stack stored in a contiguous block of memory cells (as discussed in the text). If the base of the stack is at address 0x10 and the stack pointer contains the value 0x12, what value is retrieved by a pop instruction? What value is in the stack pointer after the pop operation? Address 0x10 0x11 0x12 0x13 0x14 Contents 'F' 'C' 'A' 'B' 'E'
During the initial setup of a program, the stack pointer register is set to store the address of the last cell in data memory. Provide the address of the last cell, in hexadecimal for the ATmega2560.
For the base and offset addresses in previous problem, how many words of data are currently held in the stack ? (Previous Problem): If the current value of the stack segment register and stack pointer are C00016 and FF 0016, respec- tively, what is the address of the current top of the stack ?
3. 3. Find the contents of the stack and stack pointer after the execution of the CALL instruction shown next: Assume that SS:1296 right before the execution of CALL and SUM is a NEAR procedure. CS:IP 2450:673A CALL SUM 2450:673D DEC AH
Part 1: Preliminary Summarize the difference between binary machine language, assembly language, and high-level source files like C. Contrast the difference between a compiler, assembler, and linker What is the difference between the data segment and the text segment of in an assembly language program? What register is used as the stack pointer? What is a ebreak instruction in the sample program? How would you define a constant named 'BLUE' and assign it to the value OX00F in assembly language? Describe how to implement the psuedo-instruction li t1, e using a native instruction.
What are the purposes of the stack pointer and frame pointer registers? Why does a subroutine often need both?
The stack pointer register contains --- address of the stack segment pointer address of the stack segment offset of address of stack segment O data present in the stack segment O
The STACK is a dynamic data structure. The 80x86 computer controls its stack via stack pointer ESP. Whenever you POP data out of the stack segment memory using POP BX, the 80x86 will transfer data by: Increasing the stack pointer ESP by 4. a. b. Decreasing the stack pointer ESP by 4. Decreasing the stack pointer ESP by 2. C. d. Increasing the stack pointer ESP by 2.
(2) ¿Lihäi The stack segment register contains address of the stack segment base address of the stack segment O pointer address of the stack segment data in the stack segment O نقطتان )2( If the data is present in a register and it is referred using the particular register, then it is direct addressing mode O indexed addressing mode register addressing mode immediate addressing mode
From 61: current values in stack segment register and stack pointer: C00016 & FF0016. address of the current top of the stack CFF00
Differentiate between the Code Segment, the Data Segment, and the Stack Segment. Then, for each segment, identify the registers combination that was used to address the data objects.