Applied Statics and Strength of Materials (6th Edition)
6th Edition
ISBN: 9780133840544
Author: George F. Limbrunner, Craig D'Allaird, Leonard Spiegel
Publisher: PEARSON
expand_more
expand_more
format_list_bulleted
Concept explainers
Textbook Question
Chapter 9, Problem 9.37SP
An inclined member is braced with a glued block, as shown. The ultimate shear stress in the glued joint is 1050 psi. Determine the dimension x at which the glued joint will fail.
Expert Solution & Answer
Want to see the full answer?
Check out a sample textbook solutionStudents have asked these similar questions
For the connection shown, the bolt diameter is d = 30 mm. The average shear stress in the bolts must be limited to 160 MPa. Determine the maximum load P that may be applied to the connection based on the shear strength of the bolts.
The five-bolt connection shown must support an applied load of P = 330 kN. If the average shear stress in the bolts must be limited to 295 MPa, determine the minimum bolt diameter that may be used in the connection.
As shown in the picture below, the sloping direction of the member is subjected to a compression of 3,000 N. contact surfaceDetermine the compression stress generated by AB and BC and the shear stress acting on the horizontal plane DB.
Chapter 9 Solutions
Applied Statics and Strength of Materials (6th Edition)
Ch. 9 - Write the direct stress formula in its three forms...Ch. 9 - A 6-in-diameter concrete test cylinder is loaded...Ch. 9 - Determine the tensile stress in each segment of...Ch. 9 - Calculate the stress developed in the following...Ch. 9 - The following members are subjected to axial...Ch. 9 - Determine the stresses in the two segments of the...Ch. 9 - A bin weighing 8 tons is supported by three steel...Ch. 9 - Diameters of small commercially available steel...Ch. 9 - A No. 32 (metric designation) reinforcing bar for...Ch. 9 - In the bolted connection of Figure 9.12 , assume...
Ch. 9 - Compute the force required to punch a...Ch. 9 - The 34 — in. — diameter bolt shown is subjected to...Ch. 9 - Why is strain unitless (or dimensionless)?Ch. 9 - (a) Given =1.2in. and L=100ft calculate (b) Given...Ch. 9 - A short compression member 2 in. by 2 in. in cross...Ch. 9 - A 100-ft-long rod is suspended from one end. The...Ch. 9 - Compute the total elongation of a steel bar,...Ch. 9 - A steel rod 34 in. in diameter and 25 ft long is...Ch. 9 - An aluminum rod 25mm in diameter and 4m long is...Ch. 9 - A steel rod 10 ft long is made up of two 5 ft...Ch. 9 - A titanium alloy bar elongates 0.500 in. when...Ch. 9 - Write a program that will calculate the allowable...Ch. 9 - Write a program that will compute stress, strain,...Ch. 9 - The Viking Bin Company manufactures suspended bins...Ch. 9 - Write a computer program that will calculate the...Ch. 9 - The joint between a diagonal and a chord in a...Ch. 9 - In Problem 9.26, find the required length of the...Ch. 9 - A column is supported by a base plate, pedestal,...Ch. 9 - If the soil pressure under the footing of Problem...Ch. 9 - A hopper weighing 75 kN is supported by three...Ch. 9 - A steel bar has a rectangular cross section 25 mm...Ch. 9 - A steel wire is suspended vertically from its...Ch. 9 - A W1240 shape is subjected to a tensile load of...Ch. 9 - Calculate the required diameter of steel tie rods...Ch. 9 - A 30-ft-long steel rod of circular cross section...Ch. 9 - Consider the bolted lap joint shown in Figure...Ch. 9 - An inclined member is braced with a glued block,...Ch. 9 - Calculate the force a punch press must exert if it...Ch. 9 - A 34 - in. - diameter punch is used to punch a...Ch. 9 - A control arm is keyed to a 1-in. -diameter shaft...Ch. 9 - Calculate the required width b for the key of...Ch. 9 - A 25-mm-diameter aluminum rod, 3 m long, is...Ch. 9 - A short timber post of Douglas fir is subjected to...Ch. 9 - A 1 00-ft surveyor’s steel tape with a...Ch. 9 - An 18-in-long steel rod is subjected to a tensile...Ch. 9 - Compute the magnitude of the tensile load that...Ch. 9 - A 5-mm-diameter steel wire, 18 m in length, is...Ch. 9 - A structural steel rod 112 in. in diameter and 20...Ch. 9 - A rectangular structural steel eyebar 34 in. thick...Ch. 9 - 9.50 A
in. — diameter steel rod, 100 ft long, is...Ch. 9 - For the truss shown, compute the total deformation...Ch. 9 - A steel bar with a cross section of 12 in. by 12...Ch. 9 - Rework Problem 9.52 , changing the second load...Ch. 9 - In the structure shown, the tie-back BC is a round...Ch. 9 - A hook is suspended by two steel wires, as shown....Ch. 9 - The trolley of a small hoist is supported on a...Ch. 9 - The steel piston rod to the master cylinder has a...Ch. 9 - A stranded steel brake cable is composed of 7...Ch. 9 - The piston of a steam engine is 400 mm in diameter...
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.Similar questions
- Calculate the smallest area of each cable if the stress is not to exceed 76 000 KPa in bronze and 118 MPa in steel if a homogeneous 778 000 g bar AB is supported at either end by a cable.arrow_forwardA solid square steel bar is fixed at one end as shown, and is loaded with a 25 kg weight. If the limiting stress of the bar is 27.24 kPa determine the cross sectional area of the steel square bar and its dimensions.arrow_forwardA thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is increased by 1% and the thickness is reduced by 1%, with the internal pressure remaining the same, the percentage change in the circumferential (hoop) stress is.....arrow_forward
- A compression load of P = 55 kips is applied to a 2 in. by 2 in. square post, as shown. Determine the normal stress σn perpendicular to plane AB and the shear stress τnt parallel to plane AB. Assume α= 30°.Calculate the normal force N perpendicular to the plane AB and the shear force V parallel to plane AB. Report both answers as positive numbers.Answers: N = kips, V = kips.arrow_forwardThree steel plates, each 16 mm thick and width of 300 mm are joined by two 20 mm rivets as shown. Assume the rivet hole diameter = 23 mm. A. If the load P= 50 KN, determine the tensile stress of the plates. B. If the load P= 50 KN, determine the largest bearing stress acting on the rivets. C. If the ultimate shear stress for the rivets is 180 MPa, what ultimate force Pu is required to cause the rivets to fail in shear? Neglect friction between the plates.arrow_forwardA flexible connection consisting of rubber plates (thickness t = 9 mm) attached to the steel plates is shown in the figure. The plates are 160mm long and 80mm wide. (a) Determine the force that can be applied to the arrangement, if it is not to exceed a shear stress of 350kPaarrow_forward
- The lap joint shown is fastened by 4 rivets of ¾ in. diameter. Find the maximum load P that can be applied if the working stress are 14000 psi for shear in the rivet and 18000 psi for bearing in the plate. Assume that the applied load is distributed evenly in the 4 rivets. The plate is 7/8 in. thick and 4 in wide.arrow_forwardA circular tube AB is fixed at one end and free at the other end. The tubeis subjected to axialforce at joint B. If the outer diameter of the tube is 3 in, and thethickness is 3/4 in., calculate the maximum normal stress in the tubearrow_forwardThe tensile member shown, 50 mm x 75 mm in cross section is subjected to a load P. The plane A-A makes an angle 15° with the x-axis. a. Determine load P when the tensile stress at section A-A is 80 MPa. b. Determine the shear stress on section A-A. c. At what angle of plane A-A is the shear stress equal to 27.35 MPa?arrow_forward
- A paper tube is formed by rolling a cardboard strip in a spiral and then gluing the edges together as shown. Determine the shear stress acting along the seam, which is at 50° from the horizontal, when the tube is subjected to an axial compressive force of 200 N. The paper is 2 mm thick and the tube has an outer diameter of 100 mm.arrow_forwardThe bolted connection illustrated below comprises one bolt and two plates. The bolt, which has a diameter of 20 mm, is threaded through a 22- mm diameter hole in both plates. The shear stress of the bolt is 78,000 MPa. Based on this information, determine the following What is the largest force F that can be placed on the joint without shearing the bolt? what is the normal stress, at the gross section area, in each plate? what is the normal stress, at the net section area, in each plate? what is the bearing (or contact) stress between the bolt and each plate?arrow_forwardFor the clevis connection shown, the shear stress in the 0.577-in.-diameter bolt must be limited to 22 ksi. Determine the maximum load P that may be applied to the connection.arrow_forward
arrow_back_ios
SEE MORE QUESTIONS
arrow_forward_ios
Recommended textbooks for you
- Elements Of ElectromagneticsMechanical EngineeringISBN:9780190698614Author:Sadiku, Matthew N. O.Publisher:Oxford University PressMechanics of Materials (10th Edition)Mechanical EngineeringISBN:9780134319650Author:Russell C. HibbelerPublisher:PEARSONThermodynamics: An Engineering ApproachMechanical EngineeringISBN:9781259822674Author:Yunus A. Cengel Dr., Michael A. BolesPublisher:McGraw-Hill Education
- Control Systems EngineeringMechanical EngineeringISBN:9781118170519Author:Norman S. NisePublisher:WILEYMechanics of Materials (MindTap Course List)Mechanical EngineeringISBN:9781337093347Author:Barry J. Goodno, James M. GerePublisher:Cengage LearningEngineering Mechanics: StaticsMechanical EngineeringISBN:9781118807330Author:James L. Meriam, L. G. Kraige, J. N. BoltonPublisher:WILEY
Elements Of Electromagnetics
Mechanical Engineering
ISBN:9780190698614
Author:Sadiku, Matthew N. O.
Publisher:Oxford University Press
Mechanics of Materials (10th Edition)
Mechanical Engineering
ISBN:9780134319650
Author:Russell C. Hibbeler
Publisher:PEARSON
Thermodynamics: An Engineering Approach
Mechanical Engineering
ISBN:9781259822674
Author:Yunus A. Cengel Dr., Michael A. Boles
Publisher:McGraw-Hill Education
Control Systems Engineering
Mechanical Engineering
ISBN:9781118170519
Author:Norman S. Nise
Publisher:WILEY
Mechanics of Materials (MindTap Course List)
Mechanical Engineering
ISBN:9781337093347
Author:Barry J. Goodno, James M. Gere
Publisher:Cengage Learning
Engineering Mechanics: Statics
Mechanical Engineering
ISBN:9781118807330
Author:James L. Meriam, L. G. Kraige, J. N. Bolton
Publisher:WILEY
EVERYTHING on Axial Loading Normal Stress in 10 MINUTES - Mechanics of Materials; Author: Less Boring Lectures;https://www.youtube.com/watch?v=jQ-fNqZWrNg;License: Standard YouTube License, CC-BY