Experimental Study of laser cleaning Tests Laser cleaning of ethnographic object is a subject concern due to the sensitivity of substrate and materials to the traditional techniques so application of laser cleaning for elimination of contaminations requires preliminary and systematic study of adequate conditions to avoid any damage of the substrates , and for optimization of the laser parameters which will be tested such as ( number of pulse , fluence ,wave lengths and repetition rate so this experimental study aims to assist with the feasibility study of laser cleaning for removal deposits from the surface of ethnographic materials The aim of this work is • to examine the ability of using ( Q-switched Nd:YAG at 1064 nm & 532 nm ) to remove the deposits from surface of ethnographic materials without any damage also study if the is any alternations ( chemical or physical ) by doing other analysis as apart from this study • knowing the damage thresholds for ethnographic materials • studying the long term assessment for cleaning surface of ethnographic materials • studying the effectiveness of laser technique in removal the deposits • Investigation of the best wave length and pulse durations ( Q-switched Nd:YAG at 1064 nm & 532 nm ) The characterization of materials used in selected object , deterioration layers and asses the feasibility of use non contact laser cleaning could be alternative cleaning method without further mechanical or chemical contact , Also
Because laser light does not spread, the laser is ideal for precise surgical applications. The light produced is absorbed by tissue which, in turn, is consequently “harmed”. So it is important to take similar precautions when using the ESU when using lasers. Always check the power cords for frays, and check to make sure all switches are functioning properly. Also, make sure not to use any inflammable agents
Cleaning is the first step in reprocessing instruments and it is called decontamination. The cleaning process is all soiled instruments placed in the prewash ultrasonic washer for ten minutes to remove any bacterial spores for instance, blood, tissue, and bone fragments. Then the instruments are sent through a wall washer. The wall washers are designed for the final cleaning of all instruments. Once the washer is finished, it unloads in the
must always follow the surface coating rules and guidelines that has to formulated on a basis of
Dental hygienists face ethical dilemmas on a daily basis; we need to understand and balance our patient's needs versus their expectations. Patients tend to judge our skills as clinicians based on what they see in their mouths, and this includes extrinsic stain. Esthetic procedures like bleaching or polishing can be uncomfortable and create unnecessary trauma to the hard and soft tissue and pulp. Safe, effective treatment involves more than shoving a prophy angle onto a handpiece or a making custom-made bleaching tray for our clients. The purpose of this essay is to understand the difference between the different types of polishing, and abrasive agents and bleaching biomaterials, establish safe procedures and
The base of the light triangle, b, was measured first. Then, the light positions, a, were measured f=or the first order (m=1) and second order (m=2) light beams to determine the angle Ɵ for each. This data was organized in an Excel table and used to find the wavelength, λ, of the laser through Equation 1. This value was then compared to the theoretical value for wavelength of the laser, which was 6.328x〖10〗^(-7)m, and the percent error was calculated between the two.
The word laser is an acronym for, “Light Amplified by Stimulated Emissions of Radiation”, this means that all the lights in a laser have the same wavelength. Within a century of the laser being invented it occupied a major role in scientific research, medicine, industry, and even daily life. Lasers are used in the medicine field for procedures such as, laser eye surgery, heart, stomach, and intestinal surgeries. These procedures laser procedures are said to be harmless. Major factory industries use lasers to cut many things ranging from thin
I think that I respond to this encounter on Laserfiche already. But here is my response one more time.
Next, you will need to neutralize the Parkerizing solution. Use a sonic cleaner or container with a water and simple green mixture to clean the parts. Once cleaned of the solution, the weapon parts should be oiled and reinstalled on the weapon. While Parkerizing, you should take safety precautions and wear; face protection and gloves. If possible conduct the process in a well-ventilated area.
Everything you've ever learned in gun safety also applies to cleaning time in addition to some other tips. Keep the gun pointed in a safe direction at all times. Always treat the gun as if it were loaded. Keep ammunition out of and away from the guns while cleaning. Don't look through the end of the muzzle to check if the barrel's clean, look through the breach instead. Finally, keep your finger off the trigger at all times.
Laser engraving is nothing but creating marks on objects with the use of laser technology. This engraving task is now growing like anything as most of the commercial industries are in need of the same. In this case, 3D technology is also involved for making the marking more accurate. There are innumerable engraving materials that are being listed so that this advanced technology can be used and they are plastic, glass, acrylic, wood, fabric, corian, leather, anodized aluminum, coated metals, pressboard, Mylar, ceramics and many more. CO2 based laser source is being utilized for making the engraving function done in a proper manner.
The laser vaporizes tissue it comes into contact with or cuts tissue, and it is strengthens the bond between a tooth and its filling when used during the curing process. It also boosts the tooth whitening process, acting as a heat source during this procedure," Dr. Daoud continues.
Something bad that turned out to be pretty good in my life is the time I missed out on going to the water park with my cousins. Although I don’t really like going to places teeming with people such as a water park especially, on hot summer day such as that one. I stayed home with my dad and it was boring with a capital “b” but as time went on through that day I suggested he allow me go out with friends to laser tag or the movies. I contacted a few of my friends and they all said they would like to go, we met at Laser Quest and played three long games of laser tag. We got pretty tired, so my friend Noel and I walked to get a pizza from a pizza parlor that was right next to the laser tag building. We all suggested pepperoni but Noel was a vegetarian,
aser tag is a fun thing to do. You can help your brother out,but at the end you can’t help him. You can,t help no at the end,because they will try to win ,but the best thing is to have fun. Laser tag is good for your family to play together. My brother helps me and I help him to. One thing you can’t always help your family in laser tag.
The concept of treatment with light and photoactive compounds can be traced back over 6000 years to the ancient Egyptians who used light-sensitive substances (psoralens) by crushing leaves of plants related to parsley with sunlight to treat sunburns.(100)Indians also believed that vitiligo could be treated by the combination of extracts of Psoralea corylifolia and light.(100) But the actual breakthrough came by Finsen’s research in 1901 in which he showed that skin tuberculosis could be successfully treated with natural and artificial ultraviolet light.(101)
This is to certify that the report entitled “SURFACE MICROPATTERNING OF PURE TITANIUM FOR BIOMEDICAL APPLICATIONS VIA HIGH ENERGY PULSE LASER PEENING” is a bonafide record of the Seminar done by AMAL RAJ S(Roll No.: B110211ME), in partial fulfillment of the requirements for the award of degree of Bachelor of Technology in Mechanical Engineering from National Institute of Technology Calicut.