. A power station has a connected load of 48 MW. The energy generated for the year is 61,500 MWh. If the station has a load factor of 35%, solve the demand factor of the station. Answer: 0.4179 or 41.79% Subject: Distribution System and Substation Design

. A power station has a connected load of 48 MW. The energy generated for the year is 61,500 MWh. If the station has a load factor of 35%, solve the demand factor of the station. Answer: 0.4179 or 41.79% Subject: Distribution System and Substation Design

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.10P: For the circuit element of Problem 2.3, calculate (a) the instantaneous power absorbed, (b) the real...

See similar textbooks

Related questions

Q: Calculate IR3 in mA of the circuit with R1=1228 ohms, R2=2326 ohms, and R3=3158 ohms and a supply vo...

Q: The resistors in series are (select all that apply): 12 N 9Ω 10 V

A: In this question we will find series connected resistors in circuit....

Q: culate the real power P, reactive power Q and apparent power S, inclu Xc R A .07S XC = 35, R= 150N; ...

Q: Put the following differential equations into state-space form. Clearly show and box the A and B mat...

Q: D Question 6 For the sine wave shown below determine the RMS voltage. The Horizontal scale "time bas...

Q: For the circuit below, assume the load was connected between nodes a and b and it has been removed. ...

A: The thevenin equivalent and the current through the load resistor can be obtained by using the basic...

Q: For each of the topics below, give ONE example demonstrates the application of mechanical sciences i...

A: GIVEN: application of mechanical science inter related to electrical engineering discipline FIND: o...

Q: Find the time constant for the RC circuit in Fig.

A: To solve above question, one should understand the behavior of Inductor and capacitor in DC circuit....

Q: 1. If the input voltage 32VP.P and f=50HZ, sketch the output of the circuit shown below. 10kn TD ZD ...

Q: ower electronics relate to the control and flow of an electrical energy. but why power electronic is...

A: Modern systems get their blood from power electronics.Distributed generation or DG in the smart grid...

Q: what are exambles of low linear energy transfer (LET) and high (LET) radiation?

Q: 10 1F 1Q i1(t) IF 12(t) 2H

Q: Calculate the real power P, reactive power Q and apparent power S, include units and show calculatio...

Q: . Implement the following circuit using components for an and gate, an or gate, and an inverter. You...

A: Given the following the circuit as shown below: We need to write the code for circuit implementatio...

Q: A big PCB manufacturing and assembly factory has collected manufacturing data as shown in Table Q2(b...

Q: 16. Calculate the output voltage, V, in the circuit of Fig. 14.55.

Q: alculate the equivalent inductor (mH) for the circuit.L1= 4mH, L2 = 1mH, and L3 = 1mH. %3D L2 L1 ell...

A: Please refer the attached images for the complete answer..

Q: abcda: (2) 10.0v - (6.0 0)/, - (2.0 0)/3 = 0 befcb: -(4.0 0)I, - 15.00 V + (6.0 n)I, - 10.0 V = 0 (3...

A: Ans 1) From the fig, apply junction law at point C ( The total incoming current = total outgoing cur...

Q: EI AL IP Зі ↑ 6A

A: Given circuit shown

Q: (b) Compare and construct the band energy diagram of conductor, insulator and semiconductor material...

A: In conductors, insulators, and semiconductors, the " Band theory " explains the electronic conductiv...

Q: 4. Using the mesh analysis technique, determine the magnitude of Ix and Vx . Given R1= R2= 2 KS, and...

Q: MCа 8.3.1 A coaxial-cable with an inner diameter of 1 mm and outer diameter of 2.4 r filled with a d...

Q: Calculate the equivalent inductor (mH) for the circuit.L1= 7mH, L2 = 5mH, and L3 = 5mH. %3D L2 L1 el...

Q: A long straight co-axial cable with two coaxial conductors of negligible resistance lies along the z...

Q: The SCR operation characteristic is plotted for la (anode current) vs lg (gate current), Va (anode –...

A: Silicon Controlled Rectifier (SCR) is the most important and widely used member of the thyristor fam...

Q: Z. The vector RA extends from A(1,2,3) to B. If the length of Ran is 10 units and its direction is g...

Q: For a first order RL circuit, the time constant is 10 sec. At what time t will the system be already...

A: Option c 50 For first order system RL The time constant will be (L/R )

Q: most of the circuits, determine all the voltages and currents necessary this usually involves: (Eth,...

Q: Find the Laplace impedance of a series parallel circuit where 2Ω resistor is in series with the para...

A: It is given that: R=2 ΩL=2 HC=0.5 F

Q: 2. If A = 2a, + 6a, – 3a, and B = - 3n, – 4a, - Sa,, find: (a) a unit vector in the direction of A -...

Q: Find I: j2Ω 3Ω 33.8/0° V I2 :-j5 N I Vx I3 A. 43.5 V C. 48.58 V B. 34.8 V D. 43.3 V Find Vx:

Q: Use an ideal op amp to design an inverting integrator with an input resistance of 10 kN and an integ...

A: In this question we will design inverting integrator with given input resistance and time constant.....

Q: 1.5 A 10 2 40 2 ->

Q: Find the load current IL by use of norton’s theorem

A: We find the Norton equivalent circuit of the given circuit to find load current iL

Q: Prob.1. For a 5 bit ladder, if the input levels are 0 = 0 V and 1+ 10 V. Vhat are the output voltage...

A: To calculate voltage due to individual bits

Q: Find the inverse laplace transform of F(s) = 6s/(s^2 + 25) + 3/(s^2 + 25) *

A: This question belongs to signal and system . It is about inverse Laplace transform of the function ....

Q: For sensor current sinking circuit, the load is connected a. to ground b. to supply voltage c. f...

A: Consider the current sinking device is used in conjunction to the micro-controller systems.

Q: A vector is specified as G = 24xya, + 12(x2 + 2)a, + 18z2a, Given two points P(1,2, -1) and Q(-2,1,3...

A: This question belongs to electro magnetic field theory . It is based on the concept of directed unit...

Q: full load regulation

A: Voltage regulation- The ratio of the change in the voltage (i.e. rise in voltage) when full-loa...

Q: Question 6 A common-source amplifier using an E-MOSFET is shown in Figure 6. (a) Determine Vos, In, ...

A: Since part a contain many subpart, so we are supposed to answer the part one only.

Q: For high power fast control we use O a. all of the above O b. relay Oc. contactor Od. Thyristor For ...

A: For high power and fast control, generally we prefer power electronics devices. And generally all t...

Q: (e shows a toroidal core which is made of mild steel and it is wound with insulated wire. The induce...

A: Note: We are authorized to answer three subparts at a time since you have not mentioned which part y...

Q: A 16 pole, 3Φ synchronous generator has a resultant air gap flux of 0.06 wb per pole. The flux is d...

Q: The synchronous reactance of a generator is 1.0 per unit, and the leakage reactance of its armature ...

Q: O Amplitude and Phase Shift O Phase Shift O Frequency Shift O Amplitude Shift

Q: 12.43 Find f(t) for each of the following functions. 135 a) F(s) : s(s + 3)*" 10(s + 2)2 b) (s) (2 +...

A: a) F(s) = 135s (s+3)2 There are no zeros Poles are s = 0 and s= -3 (its a double pole) ...

Q: tor has lap-wound arn rotating at 100 slots 2 turms per col. 100rpm. Flux per pole is 100mWb. Armatu...

Q: Design a gate-level implementation for the following expressions using the specified gate types. Use...

A: NAND AND NOR NAND and NOR are called universal gates because any logic functions can be implemen...

Q: 11. Three 92-30° N in a delta connection and 5445° N in wye-connection have been connected to a 480V...

Q: Match the sentence, word, or equation with the best choice from the list given: - [V/A] Loop Units f...

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

a power station has a connected load of 48MW. the energy generated for the year is 61500MWh. if the station has a load factor of 35%. solve the demand factor of the station. Subject: Distribution System and Substation Design
(b) A small standalone PV system has been designed for a house where the system could generate power of 1576 Whlday from four PV panels (Panel power generation factor is 4.3). 1) Estimate the power consumption demand of that house. 2) Estimate the total Watt-peak rating of the PV modules. 3)Justify the impact of the renewable energy transition on our environment and society.
Investigate the challenges and solutions for integrating renewable energy sources into the existing power grid.
Discuss the challenges and solutions in integrating renewable energy sources, such as solar and wind, into the existing power grid.
2. Solve the following problem: A THREE-PHASE PLANT CONSUMES 600 KVA, WITH A VOLTAGE OF 2400 VOLTS AND A POWER FACTOR OF 0.8 BEHIND. a) DETERMINE THE EQUIVALENT DELTA IMPEDANCE OF THE PLANT. b) IF THE PLANT WERE A STAR, CALCULATE THE RESISTANCE, REACTANCE AND THE CORRESPONDING PASSIVE ELEMENT.
Consider a house that has a 120V mains with mains frequencyof 60hz and a service current of 100A, which follows the safety standards of theresidential facilities.(a) Calculate the maximum power capacity.(b) Within the safety limit, the following devices can all operate at the sametime? If yes, what is the total power consumed? If not, what happens if all devicesare turned on at the same time and suggest a solution to the problem?- 4800W clothes dryer.- 400W washing machine.- 1200W dishwasher.- 1000W iron.- 860W air conditioning.- 150W color television.- 110W stereo sound.- 2400W electric stove.- 1200W microwave oven.- 1800W cooler.(c) Assuming that 60% of the maximum power were used daily, what is the total costper month for a kWh value of 10 cents?(d) Sketch the waveform, determine the phase difference and calculate the rms values of thefollowing waveforms: v(t) = 60 sin(wt + 20) and i(t) = 12 sin(wt - 20).
Explore the challenges and solutions related to integrating renewable energy sources into the existing power grid, including issues like grid stability and energy storage.
“Low power factor has some adverse impact on both the transmission line and on the consumer electrical system.” Justify this statement. (minimum 200 words)
Discuss the challenges and solutions related to integrating renewable energy sources, such as solar and wind power, into the existing electrical power grid.
Discuss the whole system of primary power distribution.
Problem : In the case of an industrial load with a power factor of 0.707 lagging, consuming 100 kW, and the line voltage at 60 Hz is 480Vrms, with a line resistance of 0.1Ω between the power company's transformer and the load, calculate the amount of power saved if the load's power factor changes to 0.94 leading. The answer is "3.771 Kilo-Watt has been saved" and also I want to know the concept of 'Power Factor'.
Assume the load on the substation bus drops to 240 kW and 600 magnetizing kVAR. Also assume the capacitors remain connected to the substation. 1. a) What is the magnitude of the line-to-line voltage at the generating plant that is required to maintain a line-to-line voltage of 13.8 kV at the substation? 2. b) Will this power plant voltage level cause problems for other customers?