. A tank with vertical sides contains 0.914 m of mercury and 5.029 m of water. Find the total force on a square portion of one side 0.61 m by 0.61 m in area, half of this area being below the surface of the mercury. The sides of the square are horizontal and vertical. Ans. 21.8 kN, 5.069 m down

. A tank with vertical sides contains 0.914 m of mercury and 5.029 m of water. Find the total force on a square portion of one side 0.61 m by 0.61 m in area, half of this area being below the surface of the mercury. The sides of the square are horizontal and vertical. Ans. 21.8 kN, 5.069 m down

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 3) An overhanging beam is loaded as shown in the figure. Using EI = 20.48x106 N-m², determine the…

Q: SITUATION. At the exit of a toll gate with a single booth, vehicles arrive at random at an average…

Q: The truss is subjected to the loading shown. It is supported by a pin at A and a roller at L.…

Q: al From the figure, determine ?R.L of Q from A D E H1 H2

A: Using figure

Q: In a CD test on saturated normally consolidated clay, the sample volume during shear (i) increases…

A: Consolidated clay:- The clay is never bean overloaded that is called consolidated clay, The…

Q: 3) An overhanging beam is loaded as shown in the figure. Using EI = 20.48x106 N-m², determine the…

A: Given data:

Q: Question- In a two-dimensional stress system, the two principal stresses are 180 N/mm² (tensile) and…

A: given principal stress σ1= 180 N/mm2Let other principal stress=σ2yield stress=240 N/mm2Poisson's…

Q: The pressure tank is fabricated from spirally wrapped metal plates that are welded at the seams in…

Q: If the Whole circle direction is (34°30') and the magnetic declination is (3°30')W the : magnetic…

Q: A compression spring is made of music wire of 2 mm diameter having a shear strength and shear…

Q: A ball is thrown vertically upward with an initial speed of 96 ft/sec from the base A of a cliff…

Q: The strain components Ex, Ey, and Yxy are given for a point in a body subjected to plane strain.…

A: Given :

Q: Differentiate between Environmental resources and Natural resources

Q: Determine ultimate BOD for a wastewater having 5 day BOD at 20o C as 160 mg/L. Assume reaction rate…

Q: The aluminum and steel pipes shown in the figure are fastened to rigid supports at ends A and B and…

A: Taking forces generated at the fixed end both upwards

Q: 1. You run a frequency analysis for a pretensioned beam structure (at one end the beam is…

A: An increase in the axial compression increases the frequency of the beam and vise versa ; The…

Q: A rectangular concrete beam has a width of 250 mm and a total depth of 450 mm. It is reinforced with…

Q: 2. If the 200-lb block is released from rest when the spring is un-stretched, determine how far the…

A: Given :

Q: 3) An overhanging beam is loaded as shown in the figure. Using EI = 20.48x106 N-m², determine the…

A: Given data EI = 20.48 × 106 Nm2

Q: n exterior beam has 300 mm and a height of 600 mm, it is reinforced with 5-p25 mm bars for tension…

A: Given : an exterior beam has 300 mm and a height of 600 mm, it is reinforced with 5-p25 mm bars for…

Q: If the BOD of a municipal wastewater at the end of 7 days is 60 mg/L and the ultimate BOD is 85.0…

Q: The simply supported beam is loaded as shown in the figure. Determine the value of maximum…

A: Given A beam Required Maximum deflection ymax

Q: An approach road for a bridge needs 60000 m 3 of soil compacted to a void ratio of 0.7. There are…

A: Data given:Volume of soil required (V) =60000m3void ratio (e) =0.7Borrow pit Void ratio(e)…

Q: The BOD of a sewage incubated for one day at 30o C has been found to be 100 mg/L. What will be the…

A: Given: BOD at 30°C = 100mg/l K = 0.12 at 20°C θ=1.056 Required: Five day BOD at 20°C We know, BODt =…

Q: A pump can lift water at a discharge of 0.15m³/s to a head of 25 m. The critical cavitation number…

A: Given data:- The given Discharge, Q=0.15 m3/s The critical cavitation no, σc=0.144 The barometric…

Q: The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I= 1730…

Q: A 14-ft-long simply supported timber beam carries a P = 6.0 -kip concentrated load at midspan as…

Q: A steel bar is 6.0 ft long and has a circular cross section of diameter d₁ = 0.75 in. over one-half…

Q: A bar screen is used to treat 10 MGD of menicipal wastewater. The vertical bars are 1.27 cm wide and…

A: Answer We are given Q = 10 MGD bar width b = 1.27 cm bar depth d = 3.8 cm Minimum allowable spacing…

Q: the maximum horizontal shear stress in the beam. (b) the maximum tensile bending stress in the…

Q: 4) A simply supported beam supports the uniformly distributed load of intensity Wo. Determine the…

A: Given data Determine the safe allowable value of w0 if the flexural stress is limited to 160MPa in…

Q: Find out the deflection angles from the following observations Lines AB BC Bearing N 42° 20' E N 30°…

A: Given data in question Bearings To find out Deflection angle

Q: double tee cross section is used for the beam shown below. Assume the following lengths and loads:…

A: Given: a = 15ft b= 8 ftc= 13ftP = 22000 lbQ =7000 lb bending stress equation MI =σyM = max bending…

Q: E-11 The aluminium alloy wing section shown is subjected to a pure torque of 100kNm over its 10m…

A: The given data is shown below: Torque=100 kN-mLength=10mG=30 GPa

Q: slope. It has a side slope of 2:1 and the base width of the roadway is 12 m. (a) Compute the volume…

A: Side slope = 2:1 Base width = 12 m For station 10+110, Cross section…

Q: *The R.L, of the point A which is on the floor is 100 m and backsight reading on A is 2.455 m. If…

A: Using formula

Q: For the beam and loading shown, use the double-integration method to determine (a) the equation of…

Q: What are the differences and similarities between the disasters earthquakes and hurricanes? How will…

A: Among all-natural calamities, earthquakes, as well as hurricanes, are among the most destructive.…

Q: 5. Draw loading diagram and bending moment diagram, considering shear force diagram shown in given…

A: Given: The 1st SFD is specified for drawing Loading diagram and BMD. Consider the shear force…

Q: AWT305 x 41 standard steel shape is used to support the loads shown. Assume w = 54 kN/m, LAB = 1.8…

Q: Draw the shear and bending moment diagrams for he cantilever beam below. Label all local minima and…

Q: 3) An overhanging beam is loaded as shown in the figure. Using EI = 20.48x106 N-m², determine the…

Q: Refer to the previous problem. Determine the balanced load in kN. O1355 < 1553 1535 5135 Previous…

Q: For the beam and loading shown, use discontinuity functions to compute: (a) the deflection VA of the…

Q: A beam has a width of 300 mm and an effective depth of 500 mm. f'c = 20.7 MPa, Fy = 414 MPa, Es =…

Q: Determining the relative positions of points on above or beneath the surface of the earth by means…

A: Given :

Q: The angle of internal friction (i.c.. ) was measured from consolidated drained (1.c., CD) tests on…

A: Given data- Angle of internal friction ϕSoil sample A=well graded sandSoil sample B=uniform sand

Q: The piston of the hydraulic cylinder gives pin A a constant velocity v = 2.6 ft/sec in the direction…

Q: If the Whole circle direction is (34°30') and the magnetic declination is (3°30')W the : magnetic…

Q: 4m 20 KN 43 5 kN/m E = 200 GPa I = 2X 108 MMY

A: Using superposition theorem

Question

kindly give the diagram of the given question aty the same time the complete solution where the ans. is 21.8 kN, 5.069 m down

3.30.
A tank with vertical sides contains 0.914 m of mercury and 5.029 m of water. Find the total force on
a square portion of one side 0.61 m by 0.61 m in area, half of this area being below the surface of the
mercury. The sides of the square are horizontal and vertical. Ans. 21.8 kN, 5.069 m down

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The horizontal component for the 60 kN force is? a. 51.96 kN b. 45.94 kN c. 55.96 kN d. 35.96 kN The vertical component for the 60 kN force is? a. 20 kN b. 25 kN c. 30 kN d. 35 kN
A rectangular plate 0f 7 ft by 3.5 ft at an angle 450 with the horizontal, and the 7 ft side is horizontal. Calculate the magnitude of the force on one side of the plate and the depth of its centre of its pressure when the top of edge is (a) at free water surface(b) 1.75 ft below the water surface.
Determine the shear force V in the beam at the point located 2.50 m to the left of point C. The ground reactions and shear-force diagram are shown. -30.6 kN -48.2 kN -57.2 kN -38.2 kN -40.9 kN
Isosceles triangle gate AB below is hinged at A and weighs 1500 N. What horizontal force magnitude P is required at point B for equilibrium? Take the specific weight of the water as γwater = 9810 N/m^3
Determine the support forces and draw shear force diagram and bending force diagram L1=6m, L2= 5m a=2m, b=2m, c= 1m, d= 2m F= 10 Kn, P= 3 kN/m
The cylinder of weight, W, shown below is being hoisted up with the force F against the vertical wall. If us = 0.57 a. Determine the reaction force (resultant of normal force and frictional force) against the vertical wall. b. Calculate the force, F, needed to set the cylindrical roller in motion W or W1 (in kN) = 516
In the gate AB is hinged at B and is 1.2 m wide. What vertical force, applied at the center of gravity of the 20kN gate, will keep it in equilibrium?
Solve for support rections at A, B and C
The weight of the gate is 50 kN acting 1.2 m to the right of O. Determine the Hydrostatic Force.
vertical triangular plate with base horizontal and 3.6 m high is submerged in water. The distance between the center of gravity and the center of pressure is 20 cm. If the total force acting on one side of the triangle is 79.46 kN, find the base width of the triangle.
3.) For the given couple-force system shown, determine the horizontal component of Q. P= 335 KN Q= 44 KN R=74 KN-m Z=263 KN
Curve wall ABC is a quarter circle 9 ft into the paper. a. Compute the horizontal hydrostatic force on the wall. b. Compute the vertical hydrostatic force on the wall. c. Compute the line of action of the resultant force.