. You have been asked to select the best material for redesigning a walking stick (Figure Q4 (a)). It is basically a long pole with fixed length, L, and an unknown cross-section, A. In order to give strong support, the pole must store as much elastic energy as possible. It must be able to support under end load without buckling and the cost of material less than $o [in USD]. What is the performance for this design?

. You have been asked to select the best material for redesigning a walking stick (Figure Q4 (a)). It is basically a long pole with fixed length, L, and an unknown cross-section, A. In order to give strong support, the pole must store as much elastic energy as possible. It must be able to support under end load without buckling and the cost of material less than $o [in USD]. What is the performance for this design?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.4P

See similar textbooks

Similar questions

Figure P3–64 shows two bars of different materials separated by 0.50 mm when the temperature is 20°C. At what temperature would they touch?
You have been contracted by a company to design a system for them. The system requires that you use a very elastic material but the materials available to you are Material A which has a Young’s Modulus of 210,000 N/mm2 and Material B which has a Young’s modulus of 12,500 N/mm2 Using the deflection and stiffness equation, which material will best suit the job?
A current problem in the U.S. Air Force is the neck/shoulder fatigue experienced by pilots. To be able to fly missions at night, the pilots wear night vision goggles, which are attached to the front of the helmet. Unfortunately, these are heavy, causing a large downward torque of the head, which must be counteracted by the neck muscles, which then fatigue. To alleviate this problem, many pilots have started attaching random lead weights to the back of the helmet. Find the appropriate weight that would best balance the head and minimize neck fatigue – You must show your free body diagram. Assumptions: a) center of gravity of goggles is 20 cm in front of neck pivot point, b) load of goggles1.0 kg mass, c) center of gravity of lead weight is 10 cm behind neck pivot point, d) load of bare helmet 3 kg mass, e) center of gravity of helmet is 2 cm in front of neck pivot, f) load of head 4.0 kg mass, and g) center of gravity of head is right at neck pivot point. Answer: ___________________
One of your employees is complaining of knee pain on the R. While assessing his workstation, you noted that from a sitting position (starting position: 90 deg flexion), the employee needs to exert a lot of effort to extend his right knee to 45 deg from the starting point. The length of the limb (from the tibial tuberosity to the heel area) is measured to be 38 cm. What now is the linear distance traveled by the limb from the initial position to 45 degrees of knee extension?
What are the constraint equations for this problem?
1)To design a Gold chain a goldsmith has taken 2 gram of gold (22 K) wire with 4 mm diameter. Further, he drawn that as wire having diameter of 3 mm by using respective die. Now find the following, [Density of 22K Gold : 15.6 g/cc] a)In making of jewelry (22K) how much percentage of other metals should be added with gold. b)If the material can be readily drawn into wire then the property associated with that is? c)Find the volume of the gold used. d)What is the original dimension of the gold wire before drawn? e)Calculate Poisson’s ratio of the gold wire.
ANALYSIS OF STRUCTURE hi! please help me with my problem set. Kindly include its step by step process and its free body diagram. Thank you so much!
Hang a mass from a spring. We are interested in the moment where you pull the mass down (before you release it) to the highest point that the mass moves to. We also care about when the mass is moving its fastest. In this case, the best place to put the zero reference is where the mass is hanging before you pull on it. 1)Draw an LOL Diagram 2)What is the energy model equation? 3)Will energy be conserved? (i.e., does ΔEsys =0?)
please specify which is a determinate structure in the pictures below. Note: kindly give me detailed solution.
Describe finite element modeling?
Describe the structural diagram. Examples of modules in a structure chart may be used to explain the various sorts. What is the relevance of transform analysis?
What is the shape complexity of a motor for electric scooter/e-bikes/electric vehicle in manufacturing?(Is it simple to manufacture raw materials becoming the shape of a motor? Is it simple or to sophisticated?)