.7. A beam ISMB 450 @ 72.4 kg/m transmits a shear of 150 kN and a moment of 130 kN-m to the flange of a steel column ISHB 400 @ 82.2 kg/m. Design a suitable beam-column shop welded connection. Solution For ISMB 450 @ 72.4 kg/m, For ISHB 400 @ 82.2 kg/m, bf = 150 mm; t= 17.4 mm; tw= 9.4 mm; h2= 35.4 mm. bf = 250 mm; t= 12.7 mm ; tw= 10.6 mm

.7. A beam ISMB 450 @ 72.4 kg/m transmits a shear of 150 kN and a moment of 130 kN-m to the flange of a steel column ISHB 400 @ 82.2 kg/m. Design a suitable beam-column shop welded connection. Solution For ISMB 450 @ 72.4 kg/m, For ISHB 400 @ 82.2 kg/m, bf = 150 mm; t= 17.4 mm; tw= 9.4 mm; h2= 35.4 mm. bf = 250 mm; t= 12.7 mm ; tw= 10.6 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An A36 channel section is used as a purlin in a roof system with spacing of trusses at 4.5 m apart. Purlins are to be places at the joints and at the mid points of each top chord member. Sag rods are places at the center of each purlin. The total gravity loads consists of a dead load of 1.2 kpa roof surface (including weight of roofing and purlins) and a live load of 1.4 kPa of the roof surface. Assume the steel section is a compact section and that all loads are applied at the top flange of the purlins. Use LRFD method. (Refer to the figure for the value of equal soacing = S) Properties: Sx = 221.28 x 10^3 mm3 Sy = 19.01 x 10^3 mm3 Zx = 258.82 x 10^3 mm3 Zy = 38.51 x 10^3 mm3 Lp = 0.90 m Lr = 3.34 m Cb = 1.30 m Fy = 248 mPa Use LRFD design method. Determine the flexural strength of the purlins about the x-axis. (kN/m)
Question (1): A rectangular beam has a width b = 400 mm, and effective depth d = 850 mm and a total height h = 900 mm. The beam is subjected to an ultimate moment Mu = 1500 kN.m and an ultimate shear force Vu = 700 kN. 1- ) Design the beam for flexure to calculate the required area of steel. 2-) Using stirrups Φ 10 mm ( No.10) diameter, calculate the required spacing (s) between the stirrups at the ultimate shear force section. For all questions, Use f’c= 28 MPa and Fy= 420 MPa
subj: civil engineering A 50-mm diameter bar is used as a simply supported beam 3 m long. The flexural stress is limited to 50 MPa. If w = 36. •Find Fb(bottom) and Ft(top). (F = Mc/I) •Plot the flexural stress and draw a shear & moment diagram.
1A simply supported overhang beam is 8.0 m long. It is supported at the right end and at 2.0m from the left end. It carries a 10-kN concentrated load at the left end (0-m), a uniform linear load (4kN/m) from 2-m to 4-m and a 6-kN concentrated load at 6-m. Find the minimum shear in kN in whole number and no decimal also no units.
d.) What is the location of the absolute maximum shear from the left end of the beam? (in m) e.) What is the absolute maximum moment in the beam? (in kNm) f.) What is the location of the absolute maximum moment from the left end of the beam? (in m) I'll re-post again the other questions. Same, imclude fbd.
Situation 11. An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, Bf=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw=9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of τ= 100 MPa on shear, for bearing, σb=200 MPa on single sheer, σb= 260MPa on double shear. 3. Determine the maximum allowable moment, M(all) in kn-m, base on the beam's cross-section. 4. Determine the location of the maximum moment on the beam in meters.
Situation 11. An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, Bf=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw=9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of τ= 100 MPa on shear, for bearing, σb=200 MPa on single sheer, σb= 260MPa on double shear. 7. Determine the maximum shearing stress on the beam in MPa. 8. Determine the flexural stress, In MPa, on the fiber 30mm above NA at distance 1m from A
Situation 11. An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given below: Depth, D=225 mm Flange Width, Bf=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw=9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of τ= 100 MPa on shear, for bearing, σb=200 MPa on single sheer, σb=260MPa on double shear. 1. Determine the location of centroid, y, from top of the beam in mm .
Situation 11 An overhang beam is loaded as shown below. The beam cross-section was built by attaching two (2) channels to a 9mm thick plate using 16mm rivets The property of the channel is given: Depth, D=225 mm Flange Width, B=112.5 mm. Flange Thickness, tf=9mm Web Thickness, tw9 mm The allowable flexural stress on the beam is 180 MPa. Rivets has a capacity of t 100 MPa on shear, for bearing, o.-200 MPa on single sheer, a-260MPa on double shear Determine the location of centroid, y, from top of the beam in mm Determine the moment of inertia, I, of the section in mm^4. Determine the maximum allowable moment, M(all) in kn-m, base on the beam's cross-section. Determine the location of the maximum moment on the beam in meters. Determine the maximum moment, in kN-m, on the beam Determine the maximum flexural stress on the beam in MPa.
The beam is subjected to a service dead load of 2.5k/ft for the entire length and a service live load of 20 kips at 4 ft from left end. The self weight of the beam b = 12in h=24 in has to be added to the dead load for the calculations. According to the figure how much is the maximum shear for the design load diagram Vmax? How much is the max bending moment for the design load diagram Mmax?
2. The beam AB shown is supported at A and B. the beam is loaded with three fixed concentrated loads and an overhead hoist carrying a load W. P1 P2-320 KN. P3-200 KN and W-500 KN A. Find the distance of W from A in meters if the resultant of the external loads is at the midspen B. What is the reaction at A when W is at midspan?
# 1. A W30x99 beam carries a concentrated load of 800 kN at its midspan. Using A36 steel with Fy = 248 MPa. Neglect self-weight of the beam. Properties of a W30x99 section:A = 18,744 mm^2 tw = 13.26 mmd =752.66 mm tf =17.02 mmbf = 265.63 mm k =36.51 mm a. Compute the minimum bearing length Nr at the end reactions in order to prevent web yielding in mm. b. Compute the minimum bearing length Nr over which the load must be distributed in order to prevent web crippling in mm. c. Compute the minimum bearing length Nr over which the load must be distributed in order to prevent web crippling in mm.