2.a Determine the output voltage for the circuit (a) for each input voltage in (b), (c), and (d).ViaVinR1+25 v+12 V+5 V4.7 koVinVout0-0-R24.7 kN–25 V-12 V-5 V(a)(b)(c)(d)Indicate the peak values (up to 2 significant decimal places) during the positive and negative half cycles. No need toindicate the sign.(b) positive half cycle peak Vout = +Vnegative half cycle peak Vout = -V(c) positive half cycle peak Vout = +Vnegative half cycle peak Vout = -V(d) positive half cycle peak Vout = +Vnegative half cycle peak Vout = -V

Answered: Image /qna-images/answer/11f6ee76-ab62-46ee-bf7f-048b36e64f24.jpg

.a Determine the output voltage for the circuit (a) for each input voltage in (b), (c), and (d). Via Via Vin R1 +25 V +12 V +5 V 4.7 kN Vin Vout 0- R2 4.7 kN -25 V -12 V -5 V! (a) (b) (c) (d) ndicate the peak values (up to 2 significant decimal places) during the positive and negative half cycles. No need to ndicate the sign. b) positive half cycle peak Vout = + V negative half cycle peak Vout = - V =) positive half cycle peak Vout = + negative half cycle peak Vout = - V d) positive half cycle peak Vout = + V negative half cycle peak Vout = -

.a Determine the output voltage for the circuit (a) for each input voltage in (b), (c), and (d). Via Via Vin R1 +25 V +12 V +5 V 4.7 kN Vin Vout 0- R2 4.7 kN -25 V -12 V -5 V! (a) (b) (c) (d) ndicate the peak values (up to 2 significant decimal places) during the positive and negative half cycles. No need to ndicate the sign. b) positive half cycle peak Vout = + V negative half cycle peak Vout = - V =) positive half cycle peak Vout = + negative half cycle peak Vout = - V d) positive half cycle peak Vout = + V negative half cycle peak Vout = -

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 3RQ: Diodes and rectifiers allow current to _________. flow in one direction only flow in both...

See similar textbooks

Similar questions

Diodes and rectifiers allow current to _________. flow in one direction only flow in both directions divide paths of flow none of the above
The ________parameters may not reflect the actual operating conditions but simply provide an indication of the level of each parameter to expect for general use. a.hybrid-pi b.hybrid c.pi d.re
Refer to the zener ckt. VZ value is 5V. Assume that VR1 is set to 1K. Find the output in volts. Do not include the unit.
Questions: Draw a circuit using:a. 2 switches (S1 & S2) to build an equivalent AND gate. Indicate output signal using LED.b. 2 transistors (S1 & S2) to build an equivalent AND gate. Indicate output using LED. c. 2 switches (S1 & S2) to build an equivalent OR gate. Indicate output signal using LED.d. 2 transistors (S1 & S2) to build an equivalent AND gate. Indicate output using LED.
In the circuit given below Vin=50V, L=2mH, C=100uF and P0=400W. The voltage source that feeds the circuit at the input does not have the ability to charge. Switches in circuit are constantly oscillating between 1 and 2. The key takes 20 us to exit one point and return to the same point. In the case ; a)What is the output voltage (V0)? b)Graph VL and IL over two periods and indicate in what mode (DCM or CCM). c)Plot VL and IL over 2 periods when inductance is 200 uH. d)Plot IC and IL over 2 periods when inductance is 30 uH.
Clamper Circuit1. At +20V, what is the output voltage?2. At -10V, what is the output voltage?3. At 0V, what is the output voltage?
SHOW YOUR COMPLETE SOLUTION AND GIVE WHAT IS ASKED. ANSWERS SHOULD BE IN 4 DECIMAL PLACES In a series transistor voltage regulator of Figure 1, the load current varies from 0 to 1.075A and the unregulated dc input varies from 24 V to 33V. The Zener voltage is 9.3 V which required at least 1 mA to stay in its regulating region. Beta is 64.Determine(d) The Zener maximum current in mA;(e) The maximum power dissipated in Zener diode in watt(s);(f) The maximum base current in mA.
For the circuit in Figure 1, the transistor is biased so that ICQ is 10 mA and VCEQ is 8 V. As a starting point, let VRE be 20% of VCC. Calculate the values needed for RE and RC.Assume β is 100. Select the nearest standard values for the two VRc=___________ Rc =____________ VRe= ___________ Ie =_____________ Re= _____________ Rth = ____________ Ith or Ib=___________ Vth =____________ R1 =_____________ R2 =_______________
What is output voltage measured across the 100 kilo ohm load if the input is 100 uV p-p? The transistor parameters are βdc =200, VBE=0.7V.
What is the current and voltage calculations in each leg of the transistors in these two circuits? and what is the reason of voltage difference between 1-0 and 0-1? I would be very glad if you can.
From the figure shown, when S1 is at 1 : up position; the following statement is not correct except: (a) Collector-emitter voltage of Q1 is approximately zero (b) the LED will illuminate (c) the base voltage of Q2 is equal to 9 V (d) (b) and (c)
VDD = 20V , RG=1M-ohm, RD=2200ohm, IDSS = 5mA, VP = -5V a. Determine the drain current ID in mA. b. Determine the drain voltage, VD c. Determine the gate to source voltage, VGS