0.05 m w. A wooden buoy (sg=0.64) is 50 mm. by 50 mm. by 3 m long is made to float in oil surface. How many N of steel (sg=7.85) should be attached to the bottom to make the buoy float with exactly 450 mm exposed above the oil surface? (Hint: You will get the Volume of steel first then use it vood 0.45 m 2.55 m BFod to solve for the Weight of steel in Newtons) BF We w S00

0.05 m w. A wooden buoy (sg=0.64) is 50 mm. by 50 mm. by 3 m long is made to float in oil surface. How many N of steel (sg=7.85) should be attached to the bottom to make the buoy float with exactly 450 mm exposed above the oil surface? (Hint: You will get the Volume of steel first then use it vood 0.45 m 2.55 m BFod to solve for the Weight of steel in Newtons) BF We w S00

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

STRENGTH OF MATERIALS Answer: Maximum tensile 38 MN/m2, maximum compressive 46 MN/m2 Please show the solution to get the answer.
Pls answer, I'll rate. Determine the force in member BD in kN.If the force is compression, enter the answer as negative.Show your complete solution. Thank you so much!
i need the answer quickly
A cast-iron cannonball is found by a diver on the bottom of a harbor (SG of harbor water = 1.02) . The cannonball has a volume of 0.1 ft3 . The cast-iron has a specific gravity of 7.40. What force (F) is necessary to lift the cannonball off the bottom (find F in lb)? (use specific weight of water = 62.4 lb/ft3 )
A square section tank of 10FT side and 7FT length as shown has the top of one side wall in the shape of a cylinder as indicated. It contains oil with SG = 0.96 (a) Determine the magnitude (in lbs) and direction (R or L) of the horizontal component Fh of the hydrostatic force acting on the curved surface. Clearly drawn DIAGRAMS are required to get full credit. (b) Determine the magnitude (in lbs) and direction (U or D) of the vertical component Fv of the hydrostatic force acting on the curved surface. Clearly drawn DIAGRAMS are required to get full credit (c) Determine the magnitude (in lbs) of the total hydrostatic force F acting on Curve AB. (d) Determine the angle that the total force acting on the gate makes with the horizontal.
To = 4.31 kN.m
Determine the design moment capacity of the reinforced concrete beam shown inFigure 1(a) if it is reinforced with 4-28-mm diameter in tension and 2- 16-mmdiameter in compression.
Please include FBD
.ll Asiacell ? 12:33 PM @ 81% HW 4.docx HW4: - The Inverted T section of a L-m simply supported beam has the properties shown in Fig. (4). Find the flange width (b) so that the allowable stresses o ension max =30 Mpa and o compression max.=90 Mpa. 20 mm W KN/m L(m) b(mm) Fig( 4)
Mechanics of deformable bodies
2) How large are the reaction forces and bar forces in the given jib? Given: F1 = 20 kN, 5/4 а 5/4 a 1/2 a I F2 = 10 kN , a = 1 m. 2a B A 4а 2a
Handliston A steel penstock 500 mm in diameter has shell thickness of 10 mm. The modulus of elasticity of the shell material is 2.0 x 105 N/mm2 & the bulk modulus of elasticity of water is 2.0 x 103 N/mm2. The pipe is designed to discharge water at a mean velocity of 2.0 m/sec. Determine the pressure rise caused by the sudden closure of a valve at the downstream end by neglecting the elasticity of the pipe material.