0.125 in. 1.875 in. 1.25 in. r = 0.25 in. 0.75 in.

Q: Determine the minimum cross-sectional area of a steel bar required to support a tensile force of 50…

A: Given Data⇒Tensile Force=50 KipsAllowable unit tensile stress=20 KsiProblem definition⇒Problem says…

Q: Determine the average nommal stress developed at points A, B, and C. 1 attachment 5.2 cm 4 cm 4 cm…

A: Normal stress acting at point A is σA=FA=4Fπd2=43 kipπ1.5748 in2=1.540 kip/in2 4 cm=1.5748 in

Q: The bar has a 60 mm by 15 mm rectangular cross section. If P = 50 kN, determine the normal stress…

A:

Q: Determine the average normal stress in rod AB if the load has a mass of 50 kg. The diameter of rod…

A: Given figure mass of the load = 50 Kg Weight of the load

Q: Determine the torsional stress in the thin-walled tube as shown:

A:

Q: The steel bracket is used to connect the ends of two cables. If the applied force P = 1.50 kip,…

A: Draw the free body diagram.

Q: The thin-walled cylinder can be supported in one of two ways as shown. Determine the state of stress…

A: Given data as per the question Internal pressure = 65 psi Wall thickness = 0.25 in Diameter = 8 in…

Q: Determine the vertical stress increase, Ao,, at point A if q = 2895.8 kN/m. %3D 250 AN Answer ORPa…

A: Problem

Q: The screw of the clamp exerts a compressive force of 500 lb on the wood blocks. Determine the…

A: Area at section (a-a) Moment of inertia at section (a-a)

Q: The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this sleeve is…

A: Here the steel bolt and bronze sleeve are part of same component. Hence  due to application of force…

Q: The center post B of the assembly has an original length of 123 mm, whereas posts A and C have a…

A:

Q: HWs. 1. The grains of wood in the board make an angle of 20° with the horizontal as shown. Using…

A: As per given question  Axial load=250N Angal=20° Width=25mm Thickness=60mm We have to draw mohr…

Q: Determine the stress (in psi) in member BD if the cross-sectional area of the BD is 1.89 in2 P =…

A:

Q: Axial loads are Bronze Aluminum Steel applied to the compound rod that is composed of an aluminum…

A:

Q: 10. The plate welded to the end of the l-beam is fastened to the support with four 10-mm-diameter…

A: Given: d = 10 mm             P = 30 kN To determine: Normal stress & Shear stress Concept:…

Q: A thick cylindrical shell of internal diameter 150 mm has to withstand an internal fluid pressure of…

A:

Q: Determine the required thickness of member BC to the nearest 116 in., and the diameter of the pins…

A: Given: The allowable normal stress in member BC, σall = 29 ksi The allowable shear stress in pin,…

Q: Determine the stress in member CE assuming that the area in steel is 24 mm^2 p= 5 kN 3m 2m 2m 2m

A:

Q: The pedal crank for a bicycle has the cross section shown. If it is fixed to the gear at B and does…

A: Given data: The magnitude of the force subjected on the pedal is; F = 50 lb.   Draw the…

Q: The steel bracket is used to connect the ends of two cables. If the allowable normal stress for the…

A: Given data

Q: 3. Determine the required thickness of member BC and the diameter of the pins at A and B if the…

A: Given: A uniform distributed load of 5 kip/ft applied on member AB. The length of the AB is 10 ft.…

Q: The lever is attached to the shaft A using a key that has a width d and length of 25 mm. If the…

A: Given data:  Vertical force                          (Fy) = 200 N (downwards) (perpendicular to the…

Q: If the average normal stress in each of the 20-mm-diameter bars is not allowed to exceed 150 MPa,…

A: Given Data: The diameter of bar is d = 20 mm. The permissible stress in each bar is σ=150 MPa.…

Q: Determine the shear stresses experienced by the four identical circular bolts of diameter 20 mm used…

A: Given data: F = 150 kN d = 20 mm Need to determine the shear stress in each bolt.

Q: The assembly consists of three disks A, B, and C that are used to support the load of 140 kN.…

A: Given data P=140 KNσb=350 MPaτ=125 MPa

Q: Determine the average normal stress developed in rod AB if the load has a mass of 64 kg. The…

A:

Q: The stress of member AB is equal to the stress of member BC having a diameter of 100 mm. Determine…

A: Given data: The diameter of BC, dBC=100 mm. In the problem stresses are equal. σAB=σBC Draw the…

Q: The steel rod has a circular cross section. If it is loaded by a 500 lb vertical force as shown,…

A:

Q: A spherical gas tank has an inner radius of 6.1 m. If it is subjected to an internal pressure of 445…

A:

Q: 1. The link acts as part of the elevator control for a small airplane. If the attached aluminum tube…

A:

Q: The connection is made using a bolt and nut and two washers. If the allowable bearing stress of the…

A: Given data: The allowable bearing stress of the washers on the boards, (σb)allow = 2 ksi. The…

Q: Q2/ Determine the average normal stress developed in rod AB if the load has a mass of 100 kg. The…

A: If a force F is inclined at an angle θ with the horizontal, then the component of force along the…

Q: The thin-walled pipe has an inner diameter of 0.5 in. and a thickness of 0.025 in. If it is…

A: Given: The thickness of the wall is t=0.025 in. The inner diameter of the wall is d=0.5 in. The…

Q: Determine the required thickness of member BC and the diameter o the pins at A and B if the…

A:

Q: The bar has a cross-sectional area of 400(10−6) m2. If it is subjected to a uniform axial…

A: For the F.B.D of the shaft. For the equilibrium of the shaft in horizontal direction.

Q: The beveled gear is subjected to the loads shown. Determine the stress components acting on the…

A: The free body diagram of beveled gear is shown below:

Q: If the block is subjected to a centrally applied force of P = 6 kip, determine the average normal…

A: The area of the cross-sectional = 14(6)-2(1)(4)=76 in2 σavg=PAσavg=676=0.0789 ksiσavg=PA=78.95 psi

Q: The bar has a 80 mm by 20 mm rectangular cross section. If P = 90 kN, determine the normal stress…

A:

Q: The five-bolt connection must support an applied load of P = 3800 lb. If the average shear stress in…

A:

Q: The steel bar has the dimensions shown. Determine the maximum axial force P that can be applied so…

A: Given:  Allowable tensile stress = 150 MPa To determine:  maximum axial force P

Q: Determine the required thickness of member BC to the nearest in., and the diameter of the pins at A…

A:

Q: The center post B of the assembly has an original length of 122 mm, whereas posts A and C have a…

A:

Q: The bar has a cross-sectional area of 400(10−6) m2. If it is subjected to a uniform axial…

A: Draw free body diagram of the right segment of the bar sectioned at x. Considering the equilibrium…

Q: The two portions of member AB are glued along a plane forming an angle 0 = 65°with the horizontal.…

A:

Q: The two members used in the construction of an aircraft fuselage are joined together using a 30°…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.