000175 MUOKINT 1 H.W: The column (AB) shown in figure, is a part of reinforced concrete braced frame subjected to a factored compression load of 1000 KN and equally bending moment at the top and bottom Ma 215 KN.m that will cause single curve. Assume ((the stiffness of the beams at A (l/L=0.000175m), at B= (l/L-0.00176 m²), Bans"0.54 and for column (LL.))). Hom 1- Compute column slenderness ratio. 2- Is the column classified as short or long column? 3- If the column is long what is the magnified design moment? 4- design the column Long Columns 800

000175 MUOKINT 1 H.W: The column (AB) shown in figure, is a part of reinforced concrete braced frame subjected to a factored compression load of 1000 KN and equally bending moment at the top and bottom Ma 215 KN.m that will cause single curve. Assume ((the stiffness of the beams at A (l/L=0.000175m), at B= (l/L-0.00176 m²), Bans"0.54 and for column (LL.))). Hom 1- Compute column slenderness ratio. 2- Is the column classified as short or long column? 3- If the column is long what is the magnified design moment? 4- design the column Long Columns 800

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Draw the bending moment diagram of the system under the influence of external loads below. Calculate the vertical displacement value at the intersection of the horizontal beam and vertical column member? (EI= 50000kNm2)
Block A supports a pipe column and rests as shown on wedge B. Knowing that the coefficient of static friction at all surfaces of contact is 0.25 and that θ = 45degrees, determine the smallest force P required to raise block A.
determine the vertical reaction at B in kN using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places
Draw the shear force and bending moment diagrams of the beam whose span and loading condition are given in the figure. Calculate the section rotation (θA) at point A and the vertical displacement (Yc) at point C using the moment area theorem in mm. (EI = 50000 kN.m2 ) P=3kN L1=4m L2=1.3m
For the simply supported beam carrying the concentrated load P = 176 N at its midspan, determine the magnitude of the maximum displacement (in mm) if d = 2.34 m, E = 11.24 GPa , and I =1749035mm4.
consider the moment-resisting frame. Use the portal method of analysis. Use P2 = 4 kips What is the shear force in the bottom beams (absolute value)? P1 = 2 kips What is the shear force in member EH (absolute value)? h = 11' What is the horizontal reaction at H (absolute value)? b = 25' What is the bending moment in the top beams (absolute value)? (please ignore black markings) What is the vertical reaction at I (tension positive)?
For the beam and loading shown below (L = 2.4 m, E = 200 GPa, I = 1000 mm4 and w = 30 kN/m), find (a) TThe slope at point D.(b) The reaction force at end A
Circular beam with modulus of elasticity E=70 GPaA distributed load of 35 kN/m and a bending moment of k⨯2.3 kNm are applied. Using the analytical (integral) method;a) Determine the support reactions and the moment of inertia of the section.b) Moment function and 2nd order differential equation c) Boundary conditions, slope and deflection equationsd) the angle of inclination at point B (2),e) Determine the deflection (3) at point C.K=1.85 D (mm) L (m) k⨯87 k⨯1.5
A block with mass m=(24+12)kg is pulled by a horizontal force P applied at point B in Fig.3. The coefficient of kinetic friction between the surfaces is we = (5A+5)/(25+94). When the acceleration of the block is a=(1+9)/4 m/s?, determine the cable forces Tax and Top- 0=(A+8) A=1
The 300N block rests upon a level plane for which the fk is 0.20. A force P = 100N, directed at 30° from the horizontal pulls the block and moves 80m starting from rest. If the 100N force is then removed, how much further will it travel?
For the simply supported beam carrying the concentrated load P = 268 N at its midspan, determine the magnitude of the maximum slope angle of the beam (in degrees) if d = 1.6 m, E = 11.62 GPa , and I =1694446mm4.
Determine the slope and deflection at point B of the steel beamshown in the figure. The reactions are already given. Let E = 29(10^3) ksi and I = 800in^4