03: A nozzle is a device for increasing the velocity of a steadily flowing stream of fluid. At the inlet to a certain nozzle the enthalpy of the fluid is 3025 kJ/kg and the velocity is 60 m/s. At the exit from the nozzle the enthalpy is 2790 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. (a) Find the velocity at the nozzle exit. (b) If the rate of flow of fluid is 31.6 kg/s and the specific volume at the inlet is 0.19 m/kg, find the inlet area. (c) If the specific volume at the nozzle exit is 0.5 m/kg, find the exit area of the nozzle.

03: A nozzle is a device for increasing the velocity of a steadily flowing stream of fluid. At the inlet to a certain nozzle the enthalpy of the fluid is 3025 kJ/kg and the velocity is 60 m/s. At the exit from the nozzle the enthalpy is 2790 kJ/kg. The nozzle is horizontal and there is negligible heat loss from it. (a) Find the velocity at the nozzle exit. (b) If the rate of flow of fluid is 31.6 kg/s and the specific volume at the inlet is 0.19 m/kg, find the inlet area. (c) If the specific volume at the nozzle exit is 0.5 m/kg, find the exit area of the nozzle.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Similar questions

The refrigerant R134a is passing through the diffuser with the inlet diameter of D1=1 inch; p1=150psi; and V1=1000 ft/s as a saturated vapor. The exit parameters are p2=400 psi, and velocity V2=0.5 ft/s. Heat transfer, Work, and Potential energy changes can be neglected. NOTE: Use English units. For the kinetic energy change do not forget dividing to (778*32.2) conversion factor to obtain Btu/lbm. From NIST tables use BTU/lbm units for the enthalpy. Determine: a.Exit temperature in F; b.Mass flow rate in lbm/s; c.Exit diameter D2 in inches. d.Determine exit temperature.
The refrigerant R134a is passing through the diffuser with the inlet diameter of D1=1 inch; p1=150psi; and V1=1000 ft/s as a saturated vapor. The exit parameters are p2=400 psi, and velocity V2=0.5 ft/s. Heat transfer, Work, and Potential energy changes can be neglected. NOTE: Use English units. For the kinetic energy change do not forget dividing to (778*32.2) conversion factor to obtain Btu/lbm. From NIST tables use BTU/lbm units for the enthalpy. Determine: a.Exit temperature in F; b.Mass flow rate in lbm/s; c.Exit diameter D2 in inches. d.Determine exit temperature. show and expalin each step please
Steam enters a turbine with an enthalpy of 1292 BTU/lb and leaves with an enthalpy of 1098 BTU/lb. The heat loss is 13 BTU/lb. What is the work done per BTU/min and in hp for a flow of 2 lb/sec? Provide complete solution, with diagram
Q . It is proposed to pump 8,000 kg/h of toluene at 114 oC and 1.1 atm abs pressure from the reboilerof a distillation tower to a second distillation unit without cooling the toluene before it enters thepump. If the friction loss in the line between the reboiler and pump is 7 kN/m2 and the density oftoluene is 866 kg/m3 . How far above the pump must the liquid level in the reboiler be maintained togive a net positive suction head of 3.5 m? Calculate the power required to drive the pump if the pumpis to elevate the toluene 10 m. The pressure in the second unit is atmospheric and the friction loss inthe discharge line is 35 kN/m2 . The velocity in the pump discharge line is 4 m/s.
Provide the solution and diagram. Air enters the tower at the rate of 60 kg/s. The entrance enthalpy is 86 KJ/kg and exit enthalpy of 53 KJ/kg. Find the temperature range of the tower if mass flow rate of water is 30 kg/s. A. 14.34 oC B. 16.34 oC C. 10.23 oC D. 15.76oC
A nozzle operates with steam entering at 700 kPa and 300 °C. The velocity at the inlet is 30 m/s. As the steam flows through the nozzle, the pressure decreases. Determine the area ratio value (Area / Area inlet), where Area inlet is the cross sectional area of the nozzle at the inlet, at the sections of the nozzle where the pressure values are 650, 550, 450, 350, and 250 kPa. Assume nozzle operates isentropically.
At a particular stage of a reaction turbine the mean blade speed is 140 m/sec and the steam is at a pressure of 20 bar with temperature of 250° C. Fixed and moving blades at this stage have inlet angles 30° and exit angles 20°. The stage efficiency is 80%. Determine (1) Specific entholpy drop across the stage in kJ/kg. (i) Drum Dia and blade height if heigh is one-twelfth of the drum dia. and the steam flow is 120 kg/sec. (ii) The percentage increase in the relative velocity across the bladings as a result of pressure drop across the blading.
It is proposed to pump 10,000 kg/h of toluene at 114°C and 1.1 atm abs pressure from the reboiler of a distillation tower to a second distillation unit without cooling the toluene before it enters the pump. If the friction loss in the line between the reboiler and pump is 7 kN/m^2 and the density of toluene is 866 kg/m^3, how far above the pump must the liquid level in the reboiler be maintained to give a net positive suction head of 2.5m?
At the inlet of the nozzle, the enthalpy and velocity of the fluid are 3000 kJ/kg and 50 m/s respectively. There is negligible heat loss from the nozzle. At the outlet of the nozzle enthalpy is 2450 kJ/kg. If the nozzle is horizontal, find the velocity of the fluid at exit.
The product stream flow rate is 380 kmol/h
Pls. Answer this thank you!Steam enters a turbine stage with an enthalpy of 3628 kj/kg at 70 m/s and leaves the same stage with an enthalpy of 2846 kj/kg and a velocity of 124 m/s. Calculate the power in KW if there are 5 kg/s steam admitted at the turbine throttle.
Air at a static temperature and pressure of 8°C and 75 kPa respectively enters the intake of an aircraft gas turbine engine with a velocity of 196 m/s. The intake may be regarded as a diffuser with an inlet area of 0.4 m2 and an exit area that reduces the air flow velocity essentially to zero. Calculate the mass flow rate (kg/s) of air through the intake, given the specific gas (air) constant as 287 J/(kg.K), keeping three decimal places.