03 In Fig. P4-03 the electric motor exerts a torque of 3,000 N.m on the steel shaft ABCD when it is rotating at constant speed. If the torques at B and C are as shown, det- ermine the total angle of twist between points A and D. For steel, G = 79 GPa. 1,800 N.m 1,200 N.m Electric motor d=64 mm 0.25 m d=50 mm 0.30 m d=38 mm 0.20 m D

03 In Fig. P4-03 the electric motor exerts a torque of 3,000 N.m on the steel shaft ABCD when it is rotating at constant speed. If the torques at B and C are as shown, det- ermine the total angle of twist between points A and D. For steel, G = 79 GPa. 1,800 N.m 1,200 N.m Electric motor d=64 mm 0.25 m d=50 mm 0.30 m d=38 mm 0.20 m D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A solid circular bar ABCD with fixed sup-ports is acted upon by torques T0 and 2T0 at the loca-tions shown in the figure. (a) Obtain a formula for the maximum angle oftwist fmax of the bar.(b) What is fmax if the applied torque T0 at B isreversed in direction?
Before the load P was applied, a gap, ?0 existed between the cantilever beam AC andthe support at B. Knowing that E=200 GPa, determine the magnitude of P for which thedeflection at C is δ and the reaction at B (Hint: Use the method of superposition and beam deflections in Appendix A) ?0 (mm)=2.75 δ (mm)=5.5
The slotted arm OA rotates about a fixed axis through O. At the instant under consideration, θ = 32°, θ˙ = 47 deg/s, and θ¨ = 21 deg/s2. Determine the magnited of the force F applied by arm OA and the magnitude of the force N applied by the sides of the slot to the 0.3-kg slider B. Neglect all friction, and let L = 0.64 m. The motion occurs in a vertical plane.
Two forces F1 and F2 act on the screw eye. If theirlines of action are at an angle θ apart and the magnitude ofeach force is F1 = F2 = F, determine the magnitude of theresultant force FR and the angle between FR and F1.
The 58 kg uniform beam (slender rod) is lying on the floor when the man exerts a force of F = 336 N on the rope, which passes over a small smooth peg at C. a) Determine the initial angular acceleration of the beam, in rad/s2. b) Find the horizontal reaction on the beam at A (considered to be a pin) at this instant. Express your answer in Newtons.
The 600mm diameter steel shaft is subjected to the torques shown. Determine the angle of twist of end A with respect to C, in . Assume G = 75 GPa. P=74 Ex. 3P= 3(74) = 222 2P= 2(74) =148
A rectangular beam is supported at both ends. It carries two concentrated load of 110kN, a clockwise moment of 110kN-m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 60GPa. Solve the following if the reaction at point B is 328.90256410256kN, upward. BEAM DIMENSION: Width = 190mm , Height = 390mm NOTE: b = 4.8m ; Determine the deflection at midspan
the circular bar 20m in diameter is bent into a semicircle with a mean radius of 600mm. givern P=1462N and F=800 N. 1. compute the vertical reaction at A in kN a. 886 b. 712 c. 933 d. 1232 2. compute the axial force in section a-a in kN. e. 400 f. 1266 g. 731 h. 693 3. compute the bending moment in N-m in section a-a. i. 284 j. 187 k. 667 l. 348
Given : M1 = 4000 N/m M2 = 9000 N/m P = 3600 N (downward) w1= 800 N/m (downward) w2 = 600 N/m (downward) a = 4 m b = c = d = 5 m Determine the following:a. The maximum positive shear (in N).b. The maximum negative shear (in N).c. The maximum positive moment (in N-m).d. The maximum negative moment (in N-m).e. The location of maximum shear from the left end of the beam (in m).f. The location of the maximum moment from the left end of the beam (in m). Kindly Draw the detailed Shear and Moment Diagram. Compute for all of the necessary elements, Include the proper units, use the proper formula and round-off all the answers and final answers to 2 decimal places.
Determine the reactions on the beam given the loadings below using VIRTUAL WORK METHOD. Use the reaction at C as redundant. x1= 3.5 m x2= 1.5 m w1= 30 kN/m w2= 20 kN/m M= 9 kN/m (EI)AB = 1.5EI E= 40x10^6 mm^4 I= 200000 MPa
Determine the member end moments and reactions for the continuous beam shown in the Figure (a) due to the uniformly distributed load and due to the support settlements of 10 mm at A, 50 mm at B, 20 mm at C, and 40 mm at D. Use the three-moment equation. Ans. MB =115.2 kN.m , MC = 451.2 kN.m, Ay = 138.5 kN, By = 277.9 kN, Cy = 378.7 kN, Dy = 104.9 kN
consider the moment-resisting frame. Use the portal method of analysis. Use P2 = 4 kips What is the shear force in the bottom beams (absolute value)? P1 = 2 kips What is the shear force in member EH (absolute value)? h = 11' What is the horizontal reaction at H (absolute value)? b = 25' What is the bending moment in the top beams (absolute value)? (please ignore black markings) What is the vertical reaction at I (tension positive)?